| 1 x | EXTRA NG 74" yello/blue/red (Skywing RC) |
| 1 x | Crimping tool |
| 1 x | Electric Landing Gear "Black Edition" ULTIMATUM 3.0 (Elektron Re |
| 1 x | Adaptadores carga 6s JST-XH |
| 1 x | Servo GO-1035MG 16 kg.cm 0.08s/60º |
| 2 x | Extension MPX-MPX 20 cm |
| 1 x | Starter EM Gear Power 80 |
| 1 x | 5 LiPo XH>EH adapter |
| 1 x | Adapter lead MPX/XT60 |
| 1 x | Red copper lacquer wire Ø0,2 mm (5 m) |
| 2 x | Bec MR UBEC 5A (5v/6v/7v) |
| 2 x | Balanceradapter JST-XH (Heli 47G) 2-6 c. |
| 3 x | 30 cm BEC cable (female) |
| 2 x | 2 LiPo XH>EH adapter |
| 1 x | JETImodel SINGLE BEC |
| 2 x | Dean "T" - Futaba Adapter |
| 3 x | 4 LiPo XH>EH adapter |
| 1 x | Adapter lead MPX/EC3 |
| 2 x | CC 03 |
| 1 x | Cabel charger transmitter GRAUPNER |
| 1 x | L cockpit anchor "tipe F3A" (2 pcs) |
| 1 x | SUS wire 3m (nylon coated) |
| 1 x | Steering arm 16 mm Ø 4 mm |
| 1 x | Crimping sleeves for cable 1.3 mm (10 pcs) |
| 1 x | Steering arm 16 mm Ø 4 mm (2 uds) |
| 1 x | Stainless steel cable Ø 0.52 mm - 15 kp (10 m) |
| 1 x | Vertical cockpit anchor "tipe F3A" (2 pcs) |
| 1 x | Canopy Lock V1 M3 Blue (2 pcs) |
| 1 x | Stainless steel cable Ø 0.88 mm - 60 kp (10 m) |
| 1 x | Canopy Lock V1 M3 Red (2 pcs) |
| 1 x | Aluminium alloy coupler for carbon tube 6/M4 |
| 1 x | Cap closure 33/23.5mm (2 uds) |
| 2 x | Canopy Latch |
| 1 x | Locking cable tie 2.5x100 (uds) |
| 1 x | Covered closure or fairings |
| 2 x | Locking cable tie 4.6x203 (uds) |
| 1 x | Cierre cabina aluminio Ø4, I=10 mm |
| 1 x | Crimping sleeves for cable 0.85 mm (10 pcs) |
| 1 x | Screw-lock connector M2 (2 uds) |
| 1 x | Steering arm 12 mm Ø 4 mm |
| 1 x | Steering arm 16 mm Ø 3 mm (2 uds) |
| 1 x | Electric spoiler 250 mm (2 pcs) |
| 1 x | Steering arm 16 mm Ø 3 mm |
| 1 x | Stainless steel cable Ø 0.5 mm (10 m) |
| 1 x | Horizontal cockpit anchor "tipe F3A" (2 pcs) |
| 1 x | Stainless steel cable Ø 1.3 mm (10 m) |
| 1 x | One touch canopy lock |
| 1 x | Locking cable tie 3.2x142 (uds) |
| 1 x | Servo NARO Max Std |
| 1 x | Hovercraft sailcloth |
| 1 x | 67 mm cylidric hinge Ø 5 mm (4 pcs) |
| 1 x | MAX pilot ARTF |
| 1 x | Oracover Black 10 m |
| 1 x | Dremel 3000 130W |
| 1 x | White smoke bombs AX-18 (5 pcs) |
| 4 x | Decorative caps, multicoloured, short |
| 1 x | Antena FUTABA 35 mhZ 3PM/3FRF/4V/4Y/6EX/6X/6Y/7C |
| 1 x | Transmitter Balancer SPK DX-8 |
| 2 x | Transmitter Balancer HITEC Aurora 9, JR and Spectrum (blue) |
| 2 x | Transmitter Balancer Futaba T-10CG |
| 1 x | Extension for SensorSwitch 60cm |
| 1 x | PowerBox PROFESSIONAL |
| 1 x | DUPLEX 2.4EX Central Box 220 + 2x Rsat2 |
| 1 x | PowerBox Signal Amplifier |
| 1 x | PowerBox Battery 4000 |
| 1 x | Safetyclip MPX (6 pcs) |
| 1 x | DUPLEX 2.4EX Central Box 220 + 2x Rsat2 + RC Switch |
| 1 x | BlueCom™ Adapter (Android / WP) |
| 1 x | Mobile Terminal |
| 1 x | Battlife Guard 2s |
| 1 x | GPS, Vario and altitude Sensor SBS-01G |
| 1 x | PowerBox DigiSwitch V2 JR/JR |
| 1 x | Cabin latch Fox MDM1 4m (pair) |
| 1 x | DPSI Micro SingleBat 5.9V/7.2V F3A Edition magnetic switch |
| 1 x | Optotronix X-Carrier |
| 1 x | DPSI Micro-DualBat 5.9V / 7.2V MPX-JR |
| 1 x | DPSI Micro - DualBat 5.9/7.2 MPX-2xMPX dual |
| 1 x | SBEC Jeti |
| 1 x | Extension 6 lipos XH > EH |
| 1 x | Interruptor RX/Batterie |
| 1 x | USB interface ALTIS |
| 1 x | PowerBox SparkSwitch RS |
| 1 x | Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm) |
| 2 x | CellPRO 4S Adaptader (GP/KO up to 4S) |
| 1 x | Glases Nimbus "Black" |
| 1 x | Glases Nimbus |
| 1 x | Glases Ace |
| 1 x | Straightened rod Ø 2.0 mm x 1000 mm |
| 1 x | Straightened rod Ø 0.8 mm x 1000 mm |
| 1 x | Straightened rod Ø 14.0 mm x 1000 mm |
| 1 x | Brass rod Ø 1.5 mm x 1000 mm |
| 1 x | Aluminium rod Ø 4.0 mm x 3000 mm |
| 1 x | Straightened rod Ø 4.5 mm x 1000 mm |
| 1 x | Straightened rod Ø 7.0 mm x 1000 mm |
| 1 x | Brass hexagonal rod Ø 3 mm x 1000 mm |
| 1 x | Straightened rod Ø 3.0 mm x 1000 mm |
| 1 x | Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH |
| 1 x | MAX BEC |
| 1 x | CC 01 |
| 1 x | MAX BEC 2 |
| 1 x | Opto Gas Engine Kill Switch |
| 1 x | Male/Female prolonguer for Balancer Thunder Power 6S |
| 1 x | PSC 6 |
| 1 x | Regulador Jeti Jes 045 |
| 1 x | Male prolonguer XH 30 cm 6 cell cable of silicone 0,25 mm |
| 1 x | SPS 70V 140/280 A |
| 1 x | Tip wing protector 30x10 (2 pcs) |
| 1 x | Stainless steel cable Ø 0.5 mm (2 m) |
| 1 x | Split pin 1x8 mm (10 uds) |
| 1 x | Pushrod greyline 4/3 with coupler M3 |
| 1 x | Landing gear frontal support 29x26x13,5 |
| 1 x | Screw-lock pushrod conn snap Ø 1.5 mm (2 uds) |
| 1 x | Fully Threaded Steel Rod M2,0 (2 uds) 250mm |
| 1 x | Switch Cap L (silver) |
| 1 x | Interruptor FUTABA FX-MZ (2 Posic. corto) |
| 1 x | Futaba S-Bus Rx/Gyro Link Lead |
| 1 x | JETI Counter for DC-16 (Blue) |
| 1 x | Winter-Glove DS tx |
| 1 x | Futaba Neckstrap |
| 1 x | Transmitter Balancer Futaba V |
| 1 x | Futaba Aero Large Case - Internal Foam |
| 2 x | Switch Cap M (blue) |
| 1 x | Switch Cap L (Red) |
| 1 x | Switch moment button, 2 functions, long FUTABA |
| 2 x | Battery FUTABA 18MZ |
| 1 x | Adap/Exten for Futaba 12-14C |
| 1 x | TX-Tray V1 (L) (Red) |
| 1 x | Maleta transporte FUTABA 10PX |
| 1 x | Charger FUTABA SQN30W12P-08 220v |
| 1 x | Transmitter Balancer Futaba FF9-DX7-JR-Hitec |
| 1 x | Futaba S-Bus Rx/Gyro Link Lead |
| 1 x | SWTU2 switch |
| 2 x | Switch Cap M (black) |
| 1 x | Receiver bed (Blue) |
| 1 x | Tray for FUTABA 14SG/16SZ |
| 1 x | Decorative caps, multicoloured |
| 1 x | Switch Cap L (black) |
| 1 x | Antenna Hole Cap V1 (Silver) |
| 1 x | PPM to Jack link - Tx Black (mono) DC/DS Tx DUPLEX 2,4EX |
| 1 x | Black tray 2,4EX DC-16/14/24 black |
| 1 x | JETImodel DPS 40 |
| 1 x | Tray JETI for DS-12 Black |
| 1 x | Holder for DC Transmitter/Tray DUPLEX 2,4EX |
| 1 x | DUPLEX 2.4EX Central Box 210 |
| 1 x | Tray JETI for DS-14/16/24 Black |
| 1 x | DUPLEX 2.4EX Central Box 320 + 2x Rsat2 + RC Switch |
| 1 x | DUPLEX 2.4EX Central Box 220 |
| 1 x | CC 02 |
| 1 x | Axle for motor A50-L |
| 1 x | Propadapter for motor A50-V3 |
| 1 x | Shaft for A60-XS-V2 (112,5mm) |
| 1 x | Cabling for Fox MDM1 wings |
| 1 x | Connectors banna oro 8,0 mm 5 pcs(Female) |
| 1 x | Propeller 3x2 |
| 1 x | 29x12 prop Super Silence |
| 1 x | Male Prolonger TP 4/5S |
| 1 x | Black copper lacquer wire Ø0,2 mm (5 m) |
| 1 x | Circlik for shaft 1.2 mm (10 pcs) |
| 1 x | Double conector with JR adapter and 200 mm extension |
| 1 x | CM-3 |
| 1 x | Screwdriver for Hexagon 1,27mm |
| 1 x | SPARK Switch 7.4v |
| 1 x | SPARK Switch 5.9v |
| 1 x | FX three-position switched channel, long |
| 1 x | 55% silver electrodes (2 pcs) |
| 1 x | 28x12 prop Super Silence |
| 1 x | Female connector JST SH 1.0mm with 10 cm wire |
| 1 x | SPARK Switch 12v |
| 1 x | 22x10 prop Super Silence |
| 1 x | Chili F3K 2 wing servo mounted |
| 2 x | Glider KNIRPS |
| 2 x | BABY glider (Aero-naut) |
| 1 x | Three-function control switch by FUTABA |
| 1 x | Tray FUTABA T6K,T10J,T12K,T14SG,T16iZ,T18SZ,T18MZ,T32MZ |
| 1 x | Q-12 2000 mm Electric |
| 1 x | X-RAY Micro QR (Rudder) |
| 1 x | Glider IKARUS |
| 1 x | Glidder Mü13e (Bergfalke) |
| 1 x | X-RAY Micro QR (Tail Tube) |
| 1 x | X-RAY Micro QR (Elevator) |
| 1 x | Three-function control switch by FUTABA |
| 1 x | FPV Station for SE TX-Tray V1 |
| 1 x | Glider STROLCH |
| 1 x | DINO Glider ARC |
| 1 x | X-RAY Micro QR |
| 1 x | BABY glider drawings (Aero-naut) |
| 1 x | E-FUN BUG (ROI-Import) |
| 1 x | X-RAY Micro QR (Fuselage with canopy) |
| 1 x | TX Tray V1 Hand Rests only |
 |
| 10,879.94EUR |
