| 3 x | 28x5 mm wires output (2 pcs) |
| 1 x | 11 mm Rubber pads (14 pcs) |
| 1 x | Cabin latch Fox MDM1 4m (pair) |
| 1 x | 45 mm rods + T patellas set for direction control |
| 1 x | 90 mm rods + T patellas set for direction control |
| 1 x | Cable tie mounts 4.3 (4 uds) |
| 3 x | Canopy Lock V1 M3 Red (2 pcs) |
| 2 x | Aluminium alloy coupler for carbon tube 6/M4 |
| 1 x | 80 mm rods set for direction control |
| 2 x | Cockpit aluminium closing |
| 1 x | Clip mini fixing for wing (2 pcs) |
| 3 x | Allen wheel collar M4x6 |
| 2 x | Canopy Lock V1 M3 Blue (2 pcs) |
| 4 x | Allen wheel collar M3x5 |
| 2 x | 100 mm rods set for direction control |
| 1 x | Allen wheel collar M4x4 |
| 1 x | Aluminun wheel collar 3.5 mm Ø (4 uds) |
| 1 x | 250 mm / 16 mm Airbrakes |
| 3 x | Allen wheel collar M3x3 |
| 2 x | Cable grommet Ø 4 mm (4 uds) |
| 1 x | Aluminun wheel collar 3 mm Ø (4 uds) |
| 1 x | Aluminun wheel collar 2.5 mm Ø (4 uds) |
| 1 x | Horn 13,5x16 mm (2 pcs) |
| 1 x | Threaded coupler ALU Left M2,5 Ø 3 (2 uds) |
| 3 x | SlowFlyer control horn (3 pcs) |
| 2 x | Threaded coupler ALU M3 Ø 5 (2 uds) |
| 2 x | Small aluminium horn gold (2pcs) |
| 3 x | LH long black aluminium horn L31xH30 (2pcs) |
| 2 x | Threaded coupler ALU M2,5 Ø 6 (2 uds) |
| 4 x | Threaded coupler ALU Left M3 Ø 4 (2 uds) |
| 2 x | Horn 6/27 with M3 Bearing |
| 2 x | Horn 6/35 with M3 Bearing |
| 4 x | Horn with ball 55x40 |
| 1 x | Cable with accesories |
| 1 x | Horn for flap control (1 pcs) |
| 1 x | LH long aluminium horn L31xH30 (2pcs) |
| 2 x | 20 mm carbon horn |
| 2 x | Horn 5/15 with M2 Bearing |
| 1 x | Horn 6/20 with M3 Bearing |
| 2 x | Horn 5/20 with M2 Bearing |
| 2 x | Threaded coupler ALU M2 Ø 3 (2 uds) |
| 2 x | Horn 5/10 with M2 Bearing |
| 1 x | Ferrita 17x10x6.5 mm |
| 2 x | Brass control horn M4 short for wire (4 pcs) |
| 1 x | Ferrita 14x8x5.5 mm |
| 3 x | 6 mm blue aluminium threaded horn with patella |
| 1 x | Ferrita 27x14x7 mm |
| 1 x | Threaded coupler ALU M3 Ø 4 (2 uds) |
| 2 x | Brass control horn M2 short for wire (2 pcs) |
| 2 x | Threaded coupler ALU M2 Ø 4 (2 uds) |
| 1 x | APM2.6 Power module with 5.3V DC BEC |
| 2 x | Cabel charger battery transmiter Futaba 2x0,5 qmm (50 cm) |
| 1 x | Bec MR UBEC 5A (5v/6v/7v) |
| 1 x | Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH |
| 1 x | USB HLS prog. interface |
| 1 x | Circlick securite |
| 1 x | 3 copper lacquer wire Ø0,2 mm (1 m) |
| 1 x | JETImodel SINGLE BEC |
| 2 x | Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm) |
| 1 x | Balance "Y" Wire 6S, 2x JST-XH / 1x JST-EH |
| 1 x | Copper lacquer wire Ø0,2 mm (5 m) |
| 1 x | Balance "Y" Wire 7S, 2x JST-XH / 1x JST-EH |
| 1 x | Balanceradapter JST-XH (Heli 47G) 2-6 c. |
| 2 x | Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm) |
| 1 x | TrainerCord (master-learner) |
| 1 x | Futaba External voltage input cable Futaba CA-RVIN-700 |
| 2 x | CC 02 |
| 2 x | 5 LiPo XH>EH adapter |
| 1 x | Cabel charger transmitter GRAUPNER |
| 1 x | Black copper lacquer wire Ø0,2 mm (5 m) |
| 1 x | Fixed launching hook |
| 1 x | Crimping sleeves for cable 0.85 mm (10 pcs) |
| 1 x | Steering arm 16 mm Ø 3 mm |
| 4 x | Cable grommet Ø 3.2 mm (4 uds) |
| 1 x | Landing gear frontal support 25x32x16 |
| 2 x | Screw-lock pushrod conn snap Ø 1.5 mm (2 uds) |
| 1 x | Cable grommet Ø 6.4 mm (4 uds) |
| 1 x | Steering arm 16 mm Ø 4 mm |
| 1 x | Snap short M2 (10 uds) |
| 1 x | Snap for floding prop for 2 mm axi |
| 1 x | Steering arm 16 mm Ø 3 mm (2 uds) |
| 1 x | Control for forward wheel (MINI) |
| 2 x | Split pin 1.6x16 mm (10 uds) |
| 1 x | Split M1,2x10 (10 pcs) |
| 2 x | Canopy Latch |
| 2 x | Tip wing protector 28x10x12 (2 pcs) |
| 1 x | 38x4,5 mm wires output (2 pcs) |
| 1 x | Locking cable tie 2.5x100 (uds) |
| 1 x | Cable grommet 9.5 mm (4 uds) |
| 1 x | Split pin 1x8 mm (10 uds) |
| 1 x | Steering arm 12 mm Ø 4 mm |
| 3 x | White smoke bombs AX-9 (10 pcs) |
| 2 x | AX-60 starters (5 pcs) |
| 2 x | White smoke canister 100 g |
| 1 x | Blue smoke canister 140 g |
| 2 x | Green smoke canister 140 g |
| 1 x | Green smoke canister 100 g |
| 2 x | Red smoke canister 65 g |
| 1 x | "S" set for planes |
| 1 x | Initior Transmitter FTX2 Wireless |
| 1 x | B4-0 rocket charges (6 pcs) |
| 1 x | White smoke bombs AX-60 (5 pcs) |
| 1 x | Parachutist |
| 2 x | Black smoke bombs AX-60 (5 pcs) |
| 1 x | Parachute expulsion foam |
| 1 x | Smoke set "M" |
| 2 x | White smoke canister 65 g |
| 1 x | "M" set |
| 2 x | White smoke bombs AX-18 (5 pcs) |
| 1 x | AX-60 starters (5 pcs) |
| 2 x | PCARD Wireless System |
| 3 x | Ventral support for AX-18/AX-60 |
| 1 x | Blue smoke canister 100 g |
| 1 x | Remote electric ignition system |
| 1 x | "S" set for boats |
| 2 x | Green smoke canister 65 g |
| 1 x | Mixers smoke bombs AX-60 (5 pcs) |
| 1 x | Smoke set "S" |
| 1 x | Smoke set "Glider" |
| 1 x | 3l Smoke oil |
| 2 x | Electric rocket starters (6 pcs) |
| 1 x | Yellow smoke canister 100 g |
| 1 x | Tube Pitot to PIXHAWK |
| 1 x | Fully Threaded Steel Rod Duralumin 80 mm M3 (2 pcs) |
| 1 x | Futaba Female 40 cm extension |
| 1 x | Pilot "Dick" Legends Series (Slimline) |
| 1 x | ABS angle 6,0x6,0x1000 mm |
| 2 x | L cockpit anchor "tipe F3A" (2 pcs) |
| 2 x | Aluminun wheel collar 6 mm Ø (4 uds) |
| 2 x | Small aluminium horn red (2pcs) |
| 1 x | 140 mm rods + T patellas set for direction control |
| 2 x | Support pump Xicoy X45 |
| 2 x | Threaded coupler ALU Left M2,5 Ø 4 (2 uds) |
| 1 x | 400 Newtons FEMA absorber |
| 2 x | Support Pitot JETI |
| 1 x | Angle support XT60 conector |
| 1 x | Landing gear axle Ø 6 mm (2 uds) |
| 1 x | Micro control horn (2 pcs) |
| 2 x | Aluminun wheel collar 5 mm Ø (4 uds) |
| 1 x | Horn DUBRO 1/2A |
| 1 x | Horn micro type4 Ø 0,5 (2 pcs) |
| 1 x | Single rim type C3 36/33,5/18,5 mm (pneumatics 55-70 mm) |
| 1 x | Long horn 50x26 |
| 1 x | Sistema LDS - Ø12 mmr servos Ø 6/25 spline 60º (Futaba) pitch 6 |
| 1 x | Wheel FEMA 70 mm / 5 mm |
| 1 x | Snap long M2 (10 uds) |
| 2 x | 2 LiPo XH>EH adapter |
| 1 x | MPX-Dean "T" Adapter |
| 1 x | 30 cm BEC cable (male) |
| 1 x | CC 03 |
| 1 x | Extension 5 lipos JST/C |
| 2 x | SWTU2 switch |
| 1 x | Interruptor SPS 70v 60/120A |
| 1 x | Multi-adapter balancer JST/C - TP |
| 1 x | 3 LiPo XH>EH adapter |
| 2 x | Prolonguer for Balancer Thunder Power 6S |
| 2 x | Connector Sub-D 2+5 Female |
| 1 x | TP/TopFuel - JST-EH 4/5S Adapter |
| 1 x | TP/TopFuel - XH 2/3S Adapter |
| 2 x | PSC 6 |
| 1 x | Extension 5 lipos JST - JST/C |
| 1 x | Extension 2/3 lipos JST - JST/C |
| 2 x | Male prolonguer XH 30 cm 6 cell cable of silicone 0,25 mm |
| 1 x | USB interface ALTIS |
| 1 x | Male/Female prolonguer for Balancer Thunder Power 6S |
| 2 x | Brass control horn M4 short for wire (10pcs) |
| 1 x | Brass control horn M3 short for wire (2 pcs) |
| 1 x | CC 01 |
| 1 x | Electronic switch JETI SP06 Opto |
| 2 x | Horn 20x28,5 mm (2 pcs) |
| 1 x | SERVO HOLDER |
| 1 x | Horn with ball 40x30 |
| 2 x | Cockpit plastic closing |
| 2 x | Tow hook for tug |
| 2 x | Micro screw-lock pushrod conn snap Ø 1 mm (2 uds) |
| 1 x | Steering arm 16 mm Ø 4 mm (2 uds) |
| 1 x | Tip wing protector 40x14 (2 pcs) |
| 1 x | Horizontal cockpit anchor "tipe F3A" (2 pcs) |
| 1 x | Landing gear frontal support 29x26x13,5 |
| 1 x | Jet Afterburner Simulator NF-Jet4 RY |
| 1 x | NF-3 RC set |
| 1 x | Stainless steel cable Ø 0.62 mm (10 m) |
| 1 x | Vertical mounting servo holder |
| 1 x | Towing hook |
| 1 x | Cockpit aluminium closing 5.4g |
| 1 x | Towing hook |
| 1 x | Wing bolts M3 Steel screw Red (2 pcs) |
| 1 x | Fully Threaded Steel Rod Duralumin 110 mm M3 (2 pcs) |
| 1 x | Wing bolts M6 Steel screw Blue (2 pcs) |
| 1 x | Steering arm 12 mm Ø 3 mm (2 uds) |
| 1 x | Towing hook <3m |
| 1 x | 140 mm rods set for direction control |
| 1 x | White smoke bombs AX-3 (10 pcs) |
| 1 x | 41x5,5 mm wires output (2 pcs) |
| 2 x | Wing tips support for AX-18/AX-60 (2 pcs) |
| 1 x | Propeller balancer |
| 1 x | Aro pasacable Ø20 mm (4 pcs) |
| 1 x | Recessed MPX connector support (6 pcs) |
| 1 x | Support XT60 conector (2 pcs) |
| 1 x | Soporte grifo FESTO (2 pcs) |
| 1 x | Support FUEL DOT V3 |
| 1 x | 6 mm red aluminium threaded horn with patella |
| 1 x | Sistema LDS - Ø12 mm servos Ø 5/25 spline 60º (KST) pitch 5 mm |
| 1 x | 42 mm white plastic spinner for fixed propeller |
| 1 x | Spinner plastic white fixed propeller 42 mm |
| 1 x | Sistema LDS - Ø12 mm servos Ø 5/24 spline 95º (MKS) pitch 7 mm |
| 1 x | 45 mm black plastic spinner for fixed propeller |
| 1 x | Jet Afterburner Simulator NF-Jet3 RYS |
| 1 x | Field folding model stand SebArt |
| 1 x | Propeller balancer |
| 1 x | Truck-trailer for gliders 720 x 239 mm |
| 1 x | Truck-trailer for gliders 720 x 285 mm |
| 1 x | Aro pasacable Ø25 mm (4 pcs) |
| 1 x | NoNa BB wheel Ø125x35mm in pair |
| 2 x | Altimeter Altis V4 |
| 1 x | Support pumb/filter Xicoy X45 |
| 1 x | Support conector MPX (6 pcs) |
| 1 x | Support Flush MPX Conector (6 pcs) |
| 1 x | Tube support Ø 6mm (10 pcs) |
| 1 x | Support Antena 2.4 Ghz (2 pcs) |
| 2 x | Horn 16,5x20 mm (2 pcs) |
| 1 x | Cable control set |
| 1 x | RH long aluminium horn (2pcs) |
| 1 x | Threaded coupler ALU M3 Ø 6 (2 uds) |
| 1 x | 6 mm aluminium horn with patella |
| 1 x | 5 mm M2 variable inclined horn |
| 1 x | Fully Threaded Steel Rod M2,5 (2 uds) |
| 1 x | 50 mm black plastic spinner for fixed propeller |
| 1 x | Sistema LDS - Ø12 mm servos Ø 5/25 spline 60º (KST) pitch 6 mm |
| 1 x | Spinner plastic black fixed propeller 30 mm |
| 1 x | Male connector for 12 pines AWG |
| 1 x | Propeller 8x4 Electric |
| 1 x | Extension 2/3 lipos JST/C |
| 1 x | Extension 6 lipos XH > EH |
| 1 x | Propeller RABOESCH M4 30 mm (3 Blades) (Right hydropropeller) |
| 1 x | Rigid coupling brass Ø 4.0 / 2.3 mm L: 20 mm |
| 1 x | Telemetry interface ALTIS 6 cm |
| 1 x | T-Connector 4.0 mm x 1000 mm |
| 1 x | Propeller RABOESCH M4 45 mm (3 Blades pr) (Right hydropropeller) |
| 1 x | 290 mm M5 Prop shaft |
| 1 x | U Profile ABS 5,0x10,0x1000 mm |
| 1 x | Rocket D9-7 |
| 1 x | Rocket D3-P |
| 1 x | Red smoke bombs AX-60 (5 pcs) |
| 1 x | Double conector with JR adapter and 200 mm extension |
| 1 x | CM-3 |
| 1 x | wing/fuselage connector for 3 pines AWG 20-24 |
| 1 x | USB Interface REVOLECTRIX for CellPRO 10s |
| 1 x | Male connector for 20 pines AWG |
| 1 x | DUPLEX 2.4EX MSpeed PITOT <300 Km/h |
| 1 x | DUPLEX 2.4 EX MVario2 |
| 1 x | Pins M connect Multipin connectors AWG 20-24 |
| 1 x | DUPLEX 2.4EX MUI 150 Sensor |
| 1 x | Simple take for fuel tank |
| 1 x | MAX BEC 2D plus EX |
| 1 x | Dryfluid suet for reducing |
| 1 x | DC24 II Transmitter case insert |
| 1 x | SPS 70V 100/200 A |
 |
| 5,817.16EUR |
