1 x | Quicklock washer 3 mm (10 pcs) |
1 x | Cabin latch Fox MDM1 4m (pair) |
1 x | Lock washer 2.2 mm (20 pcs) |
1 x | Carbon fiber rod 6.0 mmx1000 mm |
1 x | SUS wire 3m (nylon coated) |
1 x | Aluminium cap bolt washer M3 blue (8 pcs) |
1 x | Locking cable tie 2.5x100 (uds) |
1 x | Stainless steel cable Ø 0.5 mm (2 m) |
1 x | Carbon fiber rod 7.0 mmx1000 mm |
1 x | Canopy Lock V1 M3 Blue (2 pcs) |
1 x | Flat washer 1.7 mm (20 pcs) |
1 x | Quicklock washer 3.5 mm (10 pcs) |
1 x | Carbon fiber rod 8.0 mmx1000 mm |
1 x | Stainless steel cable Ø 0.88 mm - 60 kp (10 m) |
1 x | Carbon fiber rod 1.5 mm x 1000 mm |
1 x | Steering arm 16 mm Ø 3 mm (2 uds) |
1 x | Spring lock washer 2.6 mm (20 pcs) |
1 x | Carbon fiber rod 3.0 mm x 1000 mm |
1 x | Flat washer 3.2 mm (20 pcs) |
1 x | Aluminium wide washer M4 Black (4 pcs) |
1 x | One touch canopy lock |
1 x | Steering arm 12 mm Ø 4 mm |
1 x | Carbon fiber flat 1000x3.0x1.0 mm |
1 x | Screw-lock connector Ø 2 mm (2 uds) |
1 x | Quicklock washer 2 mm (10 pcs) |
1 x | Aluminium cap bolt washer M4 red (8 pcs) |
1 x | Flat washer 4.3 mm (20 pcs) |
1 x | Threaded coupler ALU M2,5 Ø 4 (2 uds) |
1 x | Threaded coupler ALU M2 Ø 4 (2 uds) |
1 x | Pine wood slat 2.0x2.0x1000 mm |
1 x | Clevis plastico I=44 mm / hole 3mm / pin 2 (2 pcs) |
1 x | Ball link V1 Ø7 M4/3 (6 uds) |
1 x | Pine wood slat 6.0x6.0x1000 mm |
1 x | Trailing edge BALSA 35x8x1000 mm |
1 x | Linden wood slat 3.0x3.0x1000 mm |
1 x | Threaded coupler Micro M2 Ø 0,8 (10 pcs) |
1 x | BALSA trip 2.0x10.0x1000 mm |
1 x | Foreman, scale 1:32 |
1 x | Adjustable brass horn threaded M3 |
2 x | Balanceradapter JST-XH (Heli 47G) 2-6 c. |
1 x | Receiver replacement antenna, approx. 15 |
1 x | 40,0 mm hydro-propeller (left hydropropeller) |
1 x | Foam plastic plates (310x210x2 mm) |
1 x | Distanzstück motor OS 120 AX |
1 x | Aluminium sheet 500x250x0,5mm |
1 x | Eachine EV800D 5 Inches 800x480 FPV VR Goggles Monitor |
1 x | Aluminium blue ball links M3 V1 (10 pcs) |
1 x | Threaded coupler ALU M3 Ø 6 (2 uds) |
1 x | Aluminium coupler M2/2 with ball bearing (1 pcs) |
1 x | Pine wood slat 3.0x5.0x1000 mm |
1 x | Threaded coupler ALU M3 Ø 5 (2 uds) |
1 x | Clevis plastico I=30 mm / hole 2.5mm / pin 1 (2 pcs) |
1 x | BALSA trip 10x10x1000 mm |
1 x | Ball link duraluminium M3 V1 (10 pcs) |
1 x | Kwik link AL M3 con Clip (2 pcs) |
1 x | Beech dowels 4.0 x 1000 mm |
2 x | Linden wood slat 2.0x2.0x1000 mm |
1 x | Fully Threaded Steel Rod Duralumin 110 mm M3 (2 pcs) |
1 x | Landing gear axle Ø 4 mm (2 uds) |
1 x | SERVO HOLDER |
1 x | Ø 1,6 mm pin for Kwik link MPJ2150/2157 (6 pcs) |
1 x | LA500 front gear holder |
1 x | LA500 nose |
1 x | Hard brass tubing (L 1000 mm, Ø8.0 mm, Ø7.1 m) |
1 x | Flap hinge 33x9 mm (6 pcs) |
1 x | Servo HBS 690BB HV Digital |
1 x | SERVO DES 568 MG |
1 x | Walnut wood slat 3.0x3.0x1000 mm |
1 x | Cable coupler M3 (10 uds) |
1 x | Beech dowels 2.0 x 1000 mm |
1 x | Brass rod Ø 0.5 mm x 1000 mm |
1 x | Brass rod Ø 0.8 mm x 1000 mm |
1 x | Pushrod octagone 4/3 |
1 x | Tip wing protector 40x14 (2 pcs) |
1 x | Landing gear frontal support 29x26x13,5 |
|
567.17EUR |