133.50EUR

Rainbow Autogyro
[MEGARAIN]



Aut. Rainbow con 4 palas

Aut. Rainbow con 4 palas

Aut. Rainbow con 4 palas

Aut. Rainbow con 3 palas

Aut. Rainbow con 3 palas

Aut. Rainbow con 3 palas
Autogyro was first built in 1923 by Spanish engineer Juan de la Cierva. Its development went on during thirties and in Second World War II was used in armies usually for observation purposes. In Czechoslovakia was then flown by Bata company.
Autogyro model RAINBOW is designed for model builders who has basic experiences with motor modelc comntrolled by elevator and rudder (or ailerons). No problems with starts form hand or grassy field. Landing si easy even with autogyro flying only with autorotation. Thanks to relatively big rotor diameter is flying very straightforward. In the air you can handle situations in which other models would be practically lost. Side movements of autogyro RAINBOW are made by rotor tilt. Elevator works well in the whole range of speeds and in autorotation mode allows almost vertical and very slow landing. For trasportation of autogyro it is possible to turn rotor blades back over the airframe (by slackening of two blade bolts)
Flying time varies from 10 to 20 minutes (battery 3xLion,1350mAh , motor MEGA RC 400/15/7, propeller APC10x5 E). You can use rechargeable batteries with both higher or lower capacity.
It is absolutely necessary to take off and land against the wind!

Available Options:

Combos:



temporarily out of stock
temporarily out of stock

Reviews

Customers who bought this product also purchased
3 blades set
3 blades set

temporarily out of stock
temporarily out of stock

We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x Beech dowels 3.0 x 1000 mm
1 x BALSA trip 4.0x4.0x1000 mm
1 x Beech dowels 4.0 x 1000 mm
1 x BALSA triangular 15x15x1000 mm
1 x BALSA trip 3.0x3.0x1000 mm
1 x Mahogany wood slat 2.0x2.0x1000 mm
1 x BALSA trip 2.0x2.0x1000 mm
1 x quality beech plywood BIRCH 600x300x2.0 mm
1 x A/C quality beech plywood 600x300x0.8 mm
1 x OBECHI sheet 2.0x3.0x1000 mm
1 x Pine wood slat 1.5x3.0x1000 mm
1 x A/C quality beech plywood 600x300x1.5 mm
1 x Pine wood slat 2.0x2.0x1000 mm
1 x Walnut wood slat 3.0x3.0x1000 mm
1 x Pine wood slat 10x10x1000 mm
1 x Walnut wood slat 1.5x1.5x1000 mm
1 x Pine wood slat 2.0x10.0x1000 mm
1 x Linden wood slat 2.0x2.0x1000 mm
1 x A/C quality beech plywood BIRCH 600x300x1.0 mm
1 x Mahogany wood slat 1.5x1.5x1000 mm
1 x Flap hinge (6 pcs)
1 x Miniature brass strap hinge, 1 m
1 x Gates hinge black 30x16 mm (2 pcs)
1 x Pin type hinge Al 3,0x50 mm demount (2 pcs)
1 x Pin type hinge Al 4,5x70 mm (2 pcs)
1 x 67 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs)
1 x Flap hinge 33x9 mm (6 pcs)
1 x Fast'n EZ-CA-Hinge, lite (12 uds)
1 x Long pinned hinge (6 uds)
1 x Pin type hinge Al 4,5x70 mm to wire (2 pcs)
1 x 15 mm reinforced hinge
1 x Gates hinge
1 x Nylon hinge 20x15x0,3 (10 pcs)
1 x Nylon hinge for flaps/gates 27x10,5 (2 pcs)
1 x Long pinned hinge (12 uds)
1 x Pin type hinge Al 4,5x70 mm demount (2 pcs)
1 x Nylon hinge for flaps 33x9 (2 pcs)
1 x Nylon hinge 20x20x0,3 (10 pcs)
1 x Small pinned hinge (12 uds)
1 x 67 mm cylidric hinge Ø 5 mm (4 pcs)
1 x Micro flex hinge (12 uds)
1 x 25 mm reinforced hinge
1 x Nylon hinge 15x0,3 (10 pcs)
1 x Glass fabric tape 130 g/m² (Silane, plain) 25 mm / 50M
1 x Vacuum sealing tape, 2.5 x 12 mm (up to 140 °C) 22 roll
1 x Fibra carbono 3k tela 160g/m2 100 cm x 5m
1 x Carbon roving DowAksa / 24k / 1600 tex
1 x Glass fabric tape 49 g/m² (Interglas 02037, finish FE 600/800, p
1 x Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 10 m
1 x Carbon Non-Woven, 160 g/m² 100 cm 5m
1 x Carbon Non-Woven, 160 g/m² 127 cm 5m
1 x Vacuum bag, 1200 mm x 50 m
1 x Demoulding wedge red (40 x 20 mm) 5 pcs
1 x Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 50 m
1 x Carbon Non-Woven, 160 g/m² 100 cm 10 m
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x6.0 mm (5 pcs)
1 x PIX Hawk with accesories
1 x PPM Encoder Module
1 x Threaded coupler ALU M3 Ø 4 (2 uds)
1 x 6 mm red aluminium threaded horn with patella
1 x Strip ABS 2.0x8.0x1000 mm
1 x ABS Strip 1.0x2.0x1000 mm
1 x Angle measurer
1 x Slave-cable USB Easy Sim
1 x Balsa panel 2.0x100x1000 mm
1 x 
1 x BALSA trip 5.0x5.0x1000 mm
1 x Rudder
1 x Blades 330mm
1 x Steering lever
2,203.49EUR
Manufacturers
Manufacturer Info
Mega Motor
Mega Motor Homepage
Other products
Languages
Español English
Currencies