| 1 x | Crimping sleeves for cable 0.70 mm (10 pcs) |
| 1 x | SUS wire 3m (nylon coated) |
| 1 x | Covered closure or fairings |
| 1 x | Cierre cabina aluminio Ø5, I=16 mm |
| 1 x | Stainless steel cable Ø 0.5 mm (2 m) |
| 2 x | Canopy Lock V1 M3 Red (2 pcs) |
| 2 x | Stainless steel cable Ø 1.3 mm (10 m) |
| 1 x | Locking cable tie 4.6x203 (uds) |
| 1 x | Cierre cabina aluminio Ø4, I=10 mm |
| 1 x | Cap closure 33/23.5mm (2 uds) |
| 1 x | Electric spoiler 250 mm (2 pcs) |
| 3 x | Stainless steel cable Ø 0.5 mm (10 m) |
| 2 x | Aluminium alloy coupler for carbon tube 6/M4 |
| 1 x | Crimping sleeves for cable 1.3 mm (10 pcs) |
| 2 x | Vertical cockpit anchor "tipe F3A" (2 pcs) |
| 1 x | Screw-lock connector Ø 2 mm (2 uds) |
| 1 x | Stainless steel cable Ø 0.52 mm - 15 kp (10 m) |
| 1 x | Steering arm 16 mm Ø 4 mm |
| 2 x | One touch canopy lock |
| 1 x | Canopy Lock V1 M3 Blue (2 pcs) |
| 2 x | Micro screw-lock pushrod conn snap Ø 1 mm (2 uds) |
| 2 x | Steering arm 12 mm Ø 4 mm (2 uds) |
| 1 x | Stainless steel cable Ø 0.62 mm (10 m) |
| 2 x | Small aluminium horn blue (2pcs) |
| 1 x | Horn 5/10 with M2 Bearing |
| 1 x | Brass control horn M4 short for wire (4 pcs) |
| 1 x | Horn 6/27 with M3 Bearing |
| 1 x | Horn 5/15 with M2 Bearing |
| 2 x | 6 mm red aluminium threaded horn with patella |
| 2 x | Horn 13,5x16 mm (2 pcs) |
| 1 x | 6 mm aluminium horn with patella |
| 1 x | 20 mm carbon horn |
| 1 x | Bungee HLG Premium |
| 1 x | Horn 6/20 with M3 Bearing |
| 2 x | Cable control set |
| 2 x | Threaded coupler ALU M2 Ø 4 (2 uds) |
| 1 x | Horn with ball 40x30 |
| 2 x | Threaded coupler ALU Left M2,5 Ø 3 (2 uds) |
| 1 x | Brass control horn M4 short for wire (10pcs) |
| 1 x | Brass control horn M3 short for wire (2 pcs) |
| 1 x | Horn 6/35 with M3 Bearing |
| 1 x | Threaded coupler ALU M3 Ø 5 (2 uds) |
| 1 x | Brass control horn M2 short for wire (2 pcs) |
| 1 x | Pin type hinge Al 6x98 mm (2 pcs) |
| 1 x | Miniature brass strap hinge, 1 m |
| 1 x | Small pinned hinge (12 uds) |
| 1 x | Canopy hinges for Discus 2c, Discus 2a, Ventus 2cx (2pcs) |
| 1 x | 67 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs) |
| 1 x | Mahogany wood slat 2.0x2.0x1000 mm |
| 1 x | Liston HAYA 3 x 10 x 1000 mm |
| 1 x | BALSA trip 10x10x1000 mm |
| 1 x | Pine wood slat 1.5x3.0x1000 mm |
| 1 x | BALSA trip 2.0x2.0x1000 mm |
| 1 x | Pine wood slat 3.0x7.0x1000 mm |
| 2 x | Walnut wood slat 1.5x1.5x1000 mm |
| 1 x | Beech dowels 10 mm x 1000 mm |
| 1 x | BALSA trip 3.0x5.0x1000 mm |
| 2 x | Pine wood slat 6.0x6.0x1000 mm |
| 2 x | BALSA trip 3.0x3.0x1000 mm |
| 2 x | Beech dowels 3.0 x 1000 mm |
| 1 x | Pine wood slat 3.0x10.0x1000 mm |
| 1 x | BALSA trip 2.0x10.0x1000 mm |
| 1 x | BALSA trip 4.0x4.0x1000 mm |
| 2 x | Pine wood slat 2.0x2.0x1000 mm |
| 1 x | Pine wood slat 3.0x5.0x1000 mm |
| 2 x | Pine wood slat 5.0x5.0x1000 mm |
| 1 x | OBECHI sheet 2.0x3.0x1000 mm |
| 1 x | Mahogany wood slat 3.0x3.0x1000 mm |
| 2 x | Pine wood slat 10x10x1000 mm |
| 2 x | BALSA triangular 8x8x1000 mm |
| 1 x | Walnut wood slat 3.0x3.0x1000 mm |
| 1 x | Xplorer1 anemometro |
| 1 x | Starter 12v (Max 180 and 30ccm) |
| 1 x | Starter 12v (Max 90 and 15ccm) |
| 1 x | Aceite DELUXE turbine Jet Oil 1 litro |
| 1 x | Sanyo Eneloop AA 1,2 V battery 2000 mAh |
| 1 x | 48 mm cylidric hinge Ø 2,5 mm (5 pcs) |
| 1 x | Bateria LRP 2200-7.2v 6 cell NiMH |
| 1 x | Antenna Cloverleaf 5.8 GHz Tx - Rx |
| 1 x | Aro pasacable Ø20 mm (4 pcs) |
| 1 x | Baseplate servo |
| 1 x | Carbon wing joinner 13,4 mm Ø 0,48 mm |
| 1 x | Xplorer4 anemometro |
| 1 x | Ball link Aluminio M4 x 4 x 6 x 26mm (4 uds) |
| 1 x | Cylidric hinge 33 mm Ø 2 mm (5 pcs) |
| 1 x | Aro pasacable Ø25 mm (4 pcs) |
| 1 x | AC-10 pre-rotacion with motor |
| 1 x | Z Bender - S Type Tool |
| 1 x | Panasonic Eneloop AA 1,2 V battery 19>00 mAh |
| 1 x | Digital precision scale up to 2000 g |
| 1 x | Horizontal cockpit anchor "tipe F3A" (2 pcs) |
| 1 x | Cylidric hinge 43 mm Ø 2,5 mm (5 pcs) |
| 1 x | Dust collector for mould cleaning |
| 1 x | Ball Link Plier |
| 1 x | Hot Glue Stick RED |
| 1 x | Hot Glue Stick BLACK |
| 1 x | Xplorer3 anemometro |
| 1 x | Ball link Aluminio M3 (6 uds) 27x11.9x5.9 mm |
| 1 x | 67 mm cylidric hinge Ø 4,5 mm (5 pcs) |
| 1 x | ABS tube 7.0x6.0x1000 mm |
| 1 x | 13 mm self adhesive Pinking Tape, saw tooth height 0.5 mm |
| 1 x | Socket head ball link M3 (2 uds) |
| 1 x | Carbon fabric 160 g/m² (plain weave) 100 cm x 2 m |
| 1 x | Threaded coupler ALU M2,5 Ø 3 (2 uds) |
| 2 x | Stainless steel cable Ø 0.5 mm (20 m) |
| 2 x | Split pin 1x8 mm (10 uds) |
| 1 x | Extra long horn 60x30 |
| 1 x | Horn DU-BRO 1/2 (2 pcs) |
| 1 x | 6 mm M3 variable horn |
| 2 x | BALSA trip 6.0x6.0x1000 mm |
| 1 x | Balsa panel 1.5x100x1000 mm |
| 2 x | Profile ABS triangular 4.0x1000 mm 60º |
| 1 x | Aluminum Bayonet / strongal D25 mm / 1 m |
| 1 x | PT 21x13 EL Propeller |
| 1 x | PT 22x10 EL Propeller |
| 1 x | PT 21x13 EL Propeller 3 Blade |
| 1 x | Fully Threaded Steel Rod M2,0 (2 uds) 250mm |
| 2 x | Fully Threaded Steel Rod alumin 100 mm M3 (2 pcs) |
| 2 x | Wing bolts M3 Steel screw Red (2 pcs) |
| 1 x | 250 mm / 16 mm Airbrakes |
| 2 x | Cockpit aluminium closing 5.4g |
| 1 x | BALSA triangular 6x6x1000 mm |
| 2 x | BALSA leading edge 8x10x1000 mm |
| 1 x | Linden wood slat 2.0x2.0x1000 mm |
| 1 x | Beech dowels 2.0 x 1000 mm |
| 1 x | Spinner INOVA 102 mm Black |
| 1 x | Balsa panel 1.0x100x1000 mm |
| 1 x | Balsa panel 6.0x100x1000 mm |
| 1 x | Spinner Alumin. propeller pleg. 30 mm / 5,0 mm |
| 1 x | 76 mm aluminium spinner. |
| 1 x | Spinner 100 mm CFK |
| 1 x | Spinner 80 mm GFK |
| 1 x | Hot Glue Stick GREEN |
| 1 x | Spinner INOVA 63 mm White |
| 1 x | Fuel tank 500ml (17oz) |
| 1 x | MR30 connector female |
| 1 x | Carbon fiber rod 4.0 mmx1000 mm |
| 1 x | Nylon hinge for flaps 33x9 (2 pcs) |
| 1 x | ROBART POINT HINGE 4,7mm (5 pcs) |
| 1 x | Straightened threaded rod M2-1m |
| 1 x | Aramid 50 daN 50 m |
| 1 x | Hard brass tubing (L 1000 mm, Ø4.0 mm, Ø3.1 mm) |
| 1 x | 800TVL CMOS camera for FPV |
| 1 x | TYGON tubo 15 m Diam. 3.4 x 2.0 mm |
| 1 x | MAX pilot ARTF |
| 1 x | Sparkplug ROSSI R8 |
| 1 x | Servo M2x9/16 screw (4 pcs) |
| 1 x | Servo GO-1088MGW 74 kg.cm 0.125s/60º |
| 1 x | Servo KST HS08A Wing Servo - 5.2Kg.cm 0.11s 11.0g 8mm |
| 1 x | Servo HITEC HS-5485 HB Digi |
| 1 x | Servo GO-12S70MG 20.5kg.cm 0.06s/60º |
| 1 x | Brazo servo KAVAN doble aluminio 25T - 2.5" M3 |
| 1 x | Servo GO-1023MG 7.0 kg.cm 0.09s/60º |
| 1 x | Servo GO-13 MG 13g 2.8 Kg 0.12s/60º |
| 1 x | Servo GO-1053MG 20 kg.cm 0.17s/60º |
| 1 x | Servo GO-1017MG 4.5 kg.cm 0.10s/60º |
| 1 x | Servo GO-1280 MG 40 kg.cm 0.085s/60º |
| 1 x | Servo GO-09 9g |
| 1 x | USB programador GO servos |
| 1 x | Servo GO-10S41MG 10.5 kg.cm 0.075s/60º |
| 1 x | Servo GO-12S69MG 26kg.cm 0.10s/60º |
| 1 x | Servo GO-1053 MG 20.0kg |
| 1 x | Servo KST X20 8.4-50 V8.0 45kg 8.4v Softstar |
| 1 x | Servo KST BLS915 HV V8.0 25Kg 20mm 78g |
| 1 x | Servo KST X10 MINI wing 10mm 23g 7.5Kg |
| 1 x | Servo KST X08H V5.0 HV DIGITAL Wing servo 8mm |
| 1 x | Servo KST BLS825 V8.0 HV 35Kg 8.4v |
| 1 x | Servo KST DS125MG servo ala 10mm 28g 7Kg |
| 1 x | Servo KST BLS815 HV V2.0 Servo 20mm 70g 20Kg |
| 1 x | Servo HITEC D645 MW |
| 1 x | Servo HITEC HS-53 |
| 1 x | Blue Aluminium double servo arm V3-Hitec 3-3,5inch |
| 1 x | Servo HITEC D941 TW |
| 1 x | Servo HITEC D131 MW nano |
| 1 x | Blue aluminium double servo arm V3-Hitec 3,5inch |
| 1 x | Servo Digital HITEC HS-5065 MG |
| 1 x | Servo HITEC HS-5245 MG Digi |
| 1 x | Servo lock HS-80/81/82/85 (2 pcs) |
| 1 x | Servo DITEX TD2612S |
| 1 x | Sistema LDS - Ø12 mmr servos Ø 6/25 spline 60º (Futaba) pitch 6 |
| 1 x | Sistema LDS - Ø12 mm servos Ø 6/25 spline 60º (Futaba) pitch 7 m |
| 1 x | SCANNER 46-55 Sport Scale 1:7 ARF |
| 1 x | Small adjustable aluminium control horn with bearing 2,8x15 |
| 1 x | Short adjustable control horn 3x24 |
| 1 x | Threaded coupler ALU M2 Ø 3 (2 uds) |
| 1 x | Rudder forward 90x28 "type Kato" |
| 1 x | Small aluminium horn red (2pcs) |
| 1 x | Medium extra-strong control horn with bearing 2,8x24 |
| 2 x | STEERING FRONT WHEEL SYSTEM BIDULE 111 |
| 2 x | Wing bolts M3 Steel screw blue (2 pcs) |
| 1 x | Propeller RABOESCH M4 30 mm (3 Blades) (Right hydropropeller) |
| 2 x | L cockpit anchor "tipe F3A" (2 pcs) |
| 1 x | ABS "T" angle 8.0x8.0x1000 mm |
| 1 x | ABS angle 10,0x10,0x1000 mm |
| 1 x | ABS rectangular profile 12x6.0x1000 mm |
| 1 x | ABS angle 5,0x5,0x1000 mm |
| 1 x | L-Connector 4.0 mm x 1000 mm |
| 1 x | Profile ABS half cane 2.5x1000 mm |
| 1 x | Snap for floding prop for 2 mm axi |
| 1 x | Allen wheel collar M3x3 |
| 1 x | Cockpit aluminium closing |
| 1 x | Tip wing protector 40x14 (2 pcs) |
| 1 x | Snap short M2 (10 uds) |
| 1 x | BALSA triangular 10x10x1000 mm |
| 1 x | Pine wood slat 2.0x10.0x1000 mm |
| 1 x | Charger SKY RC D200 neo |
| 1 x | Short extra-strong control horn with bearing 2,8x15 |
| 1 x | Sistema LDS - Ø12 mm servos Ø 5/25 spline 60º (KST) pitch 4 mm |
| 1 x | Horn 20x28,5 mm (2 pcs) |
| 1 x | PARAGON Trainer 46-55 1580 mm |
| 1 x | Charger LiPo Charger4 |
| 1 x | Rigid coupling brass Ø 3.0 / 2.3 mm L: 20 mm |
| 1 x | U Profile ABS 2,0x4,0x1000 mm |
| 1 x | 290 mm M4 7/8x212 mm shaft ship |
| 1 x | Wing-connector: Glass / Carbon tube (13.7/12.5) x 1000 mm |
| 1 x | ABS rectangular profile 10x5.0x1000 mm |
| 1 x | ABS angle 4,0x4,0x1000 mm |
| 1 x | Flat Connector 4.0 mm x 1000 mm |
| 1 x | Profile ABS Square 4 x 1000 mm |
| 1 x | Profile ABS half cane 8.0x1000 mm |
| 1 x | Profile ABS half cane 6.0x1000 mm |
| 1 x | Profile ABS Square 1 x 1000 mm |
| 1 x | Profile ABS half cane 7.0x1000 mm |
| 1 x | Cross Connector 4.0 mm x 1000 mm |
| 1 x | ABS angle 1.5x1.5x1000 mm |
| 1 x | Profile ABS triangular 2.0x1000 mm 90º |
| 1 x | Profile ABS half cane 4x2.5x1000 mm |
| 1 x | Steering arm 16 mm Ø 3 mm (2 uds) |
| 1 x | Split pin 1.6x16 mm (10 uds) |
| 1 x | Locking cable tie 2.5x100 (uds) |
| 1 x | Cockpit plastic closing |
| 1 x | 28x5 mm wires output (2 pcs) |
| 1 x | 38x4,5 mm wires output (2 pcs) |
| 1 x | Cable grommet Ø 3.2 mm (4 uds) |
| 1 x | Stainless steel cable Ø 0.88 mm - 60 kp (10 m) |
| 1 x | Cable grommet Ø 5 mm (4 uds) |
| 1 x | 90 mm rods + T patellas set for direction control |
| 1 x | Landing gear frontal support 29x26x13,5 |
| 1 x | Landing gear frontal support 25x32x16 |
| 1 x | Snap long M2 (10 uds) |
| 1 x | Wing bolts M6 Steel screw Red (2 pcs) |
| 1 x | Snap pin for micro clevis (10 uds) |
| 1 x | Control for forward wheel (MINI) |
| 1 x | 100 mm rods + T patellas set for direction control |
| 1 x | Cockpit metalic closing |
| 1 x | Steering arm 12 mm Ø 3 mm (2 uds) |
| 1 x | Allen wheel collar M3x5 |
| 1 x | Screw-lock pushrod conn snap Ø 1.5 mm (2 uds) |
| 1 x | Tip wing protector 30x10 (2 pcs) |
| 1 x | Canopy Latch |
| 1 x | Crimping sleeves for cable 0.85 mm (10 pcs) |
| 1 x | Steering arm 12 mm Ø 4 mm |
| 1 x | 41x5,5 mm wires output (2 pcs) |
| 1 x | Window mounting channel Type H 2.5x0.5 (2 m) |
| 1 x | Lead with adhesive (2 pcs) |
 |
| 5,165.58EUR |
.jpg "COMFORT MOUNT ø 25 mm")
