| 1 x | Z-shaped servo mount |
| 1 x | Aluminium rod Ø 4.0 mm x 3000 mm |
| 2 x | Brass hexagonal rod Ø 5 mm x 1000 mm |
| 1 x | Straightened threaded rod M2-1m |
| 2 x | Brass hexagonal rod Ø 4 mm x 1000 mm |
| 1 x | Straightened rod Ø 4.5 mm x 1000 mm |
| 1 x | Brass rod Ø 0.5 mm x 1000 mm |
| 2 x | Straightened rod Ø 7.0 mm x 1000 mm |
| 1 x | Straightened rod Ø 1.5 mm x 1500 mm |
| 1 x | Straightened rod Ø 5.0 mm x 1000 mm |
| 3 x | Brass rod Ø 1.5 mm x 1000 mm |
| 1 x | Brass rod Ø 1.0 mm x 1000 mm |
| 1 x | Straightened rod Ø 6.0 mm x 1000 mm |
| 1 x | Straightened rod Ø 3.0 mm x 1000 mm |
| 2 x | Straightened rod Ø 4.0 mm x 1000 mm |
| 2 x | Brass hexagonal rod Ø 3.5 mm x 1000 mm |
| 1 x | Straightened rod Ø 2.5 mm x 1000 mm |
| 1 x | Straightened threaded rod M3 - 1m |
| 1 x | Straightened rod Ø 0.5 mm x 1000 mm |
| 2 x | Straightened rod Ø 8.0 mm x 1000 mm |
| 1 x | DUPLEX USBa USB-Adapter for Jeti Duplex Items |
| 1 x | 2 LiPo XH>EH adapter |
| 1 x | Futaba External voltage input cable Futaba CA-RVIN-700 |
| 1 x | Red copper lacquer wire Ø0,2 mm (5 m) |
| 2 x | Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm) |
| 1 x | APM2.6 Power module with 5.3V DC BEC |
| 1 x | Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH |
| 1 x | "Y" charging 4mm wire (2 IN-1 OUT). |
| 1 x | Balance "Y" Wire 6S, 2x JST-XH / 1x JST-EH |
| 1 x | CC 03 |
| 1 x | CM-3 |
| 1 x | CC 05 |
| 1 x | TrainerCord (master-learner) |
| 1 x | 30 cm BEC cable (female) |
| 1 x | Copper lacquer wire Ø0,2 mm (5 m) |
| 1 x | MPX-Dean "T" Adapter |
| 1 x | Bec MR UBEC 5A (5v/6v/7v) |
| 2 x | Servo HITEC HS-45 HB |
| 2 x | Gear set HITEC HS-645MG/5645MG/5685MH |
| 1 x | Gear set HITEC D645 MW |
| 1 x | Servo HITEC D950 TW |
| 1 x | Gear set HITEC HS-85 |
| 1 x | Screws set for Hitec MG arms servo |
| 1 x | Servo HITEC D85 MG |
| 2 x | Servo HITEC D954 TW |
| 2 x | Camera Sony 4140+673 CCD with Built-in 200mw TX + antenna |
| 1 x | Servo Digital HITEC HS-5065 MG |
| 2 x | Servo HITEC D951 TW |
| 1 x | Servo HITEC HS-325 BB |
| 1 x | Gear set HITEC HS205/225MG/5245MG/7245MH |
| 2 x | Servo HITEC HS-311 |
| 2 x | USB Mini Camera endoscope |
| 2 x | Gear set HITEC HS-225 |
| 1 x | Gear set HITEC HS-311/322/325BB |
| 1 x | Gear set HITEC HS-125MG/5125MG |
| 1 x | Servo HITEC D-955 TW Titanium |
| 1 x | Gear set HITEC HS-56 HB |
| 1 x | Gear set HITEC HS-81 |
| 1 x | Gear carbonite set HITEC HS-6965 |
| 1 x | Servo HITEC HS-125 MG |
| 1 x | HPP-21 PLUS PC Programmer for Hitec Digital Servos |
| 2 x | Gear set HITEC HS-55 |
| 1 x | Servo HITEC D625 MW |
| 1 x | HPP-25 PLUS PC Programmer for Hitec Digital Servos Field Program |
| 2 x | SERVO HOLDER |
| 1 x | Plasti Dip Liquid Tape 429 ml orange |
| 1 x | Release wax 250ml |
| 2 x | PARTALL® Hi-Temp Wax, 340 g |
| 1 x | Spray YELLOW Inca Lexan 150ml |
| 1 x | Spray adhesive INFUTAC (Clear) 500 ml |
| 1 x | Silicone adhesive ELASTOSIL® E4, tube/ 90 ml |
| 1 x | Nitroverdu 500 ml |
| 1 x | Universal Colour Paste deep black 50 g |
| 1 x | Fixed launching hook |
| 1 x | Universal Colour Paste signal white (RAL 9003) 1 Kg |
| 1 x | |
| 2 x | 20 g tin paste |
| 1 x | Universal Colour Paste white 50 g |
| 1 x | Spray EC Red 400ml |
| 1 x | 500 ml sealer (DOPE) |
| 2 x | Ventus 1:4 set of instruments |
| 1 x | Tow hook for tug |
| 1 x | Spray adhesive AEROFIX 2 |
| 1 x | Universal Colour Paste deep black 250 g |
| 1 x | Towing hook <3m |
| 1 x | Paint gun for sprays |
| 1 x | Servoarm Aluminium SH-82 |
| 1 x | Motor DLE 200cc Premium Muffler |
| 1 x | Aluminium cap bolt washer M4 blue (8 pcs) |
| 1 x | Carbon fiber rod 1.0 mm x 1000 mm |
| 1 x | Tube Pitot to PIXHAWK |
| 1 x | Conector JR/Uni Servo male BLUE silicon (10 pcs) |
| 1 x | Parachute BACKUP X100 |
| 1 x | 6 mm M3 variable inclined horn |
| 1 x | Pasacables rectangular 40x15 mm (4 pcs) |
| 1 x | Straightened rod Ø 2.0 mm x 1000 mm |
| 1 x | Straightened rod Ø 14.0 mm x 1000 mm |
| 1 x | 800TVL CMOS camera for FPV |
| 1 x | Servo HITEC HS-5585MH |
| 1 x | USB interface ALTIS |
| 1 x | Servo KST BLS825 V8.0 HV 35Kg 8.4v |
| 1 x | Brazo servo aluminio 1.25/1.5" Futaba/MKS/Savox |
| 2 x | Opto Gas Engine Kill Switch |
| 2 x | USB Interface REVOLECTRIX for CellPRO 10s |
| 1 x | MPS Gas-Cap-Powerswitch |
| 1 x | Short Switch On/Off micro |
| 2 x | SBEC 30 D |
| 2 x | SWTU2 switch |
| 1 x | Straightened rod Ø 0.8 mm x 1000 mm |
| 1 x | Cabel charger transmitter GRAUPNER |
| 1 x | Brass hexagonal rod Ø 3 mm x 1000 mm |
| 1 x | Servo HITEC HS-5475 HB Digi |
| 1 x | Beech dowels 4.0 x 1000 mm |
| 1 x | Walnut wood slat 1.5x1.5x1000 mm |
| 1 x | OBECHI sheet 2.0x3.0x1000 mm |
| 1 x | Birch plywood plate 600x300x4.0 mm |
| 1 x | Servo HS-5070 MH Hi Volt |
| 2 x | Servo HITEC HS-65 MG |
| 1 x | Servo HITEC HS-45 HB, servo box |
| 1 x | Birch plywood plate 600x300x1.5 mm |
| 1 x | Small Crow DLE-170M |
| 1 x | Motor DLE 170 M- Paramotors |
| 1 x | Linden wood slat 2.0x2.0x1000 mm |
| 1 x | Mahogany wood slat 2.0x2.0x1000 mm |
| 1 x | Trailing edge BALSA 35x8x1000 mm |
| 1 x | Mahogany wood slat 1.5x1.5x1000 mm |
| 1 x | Birch plywood plate 600x300x2.0 mm |
| 1 x | Mahogany wood slat 3.0x3.0x1000 mm |
| 1 x | quality beech plywood BIRCH 600x300x2.0 mm |
| 1 x | Servo MKS HBL380 |
| 1 x | Servo MKS HV1220 |
| 1 x | Servo MKS HBL599 SL |
| 1 x | Lite Plywood panel 600x300x3.0 mm |
| 1 x | Pine wood slat 10x10x1000 mm |
| 1 x | Servo HITEC HSB-9380TH |
| 1 x | Servo HITEC HS-5245 MG Digi |
| 1 x | Servo HITEC HS-77 BB Low Profile |
| 1 x | Servo HITEC HS-5685MH |
| 1 x | Servo HITEC HS-53 |
| 1 x | Servo HITEC HS-7954 SH Digital High |
| 1 x | Servo HITEC HS-7950TH Ultra Torque HV Coreless Titanium Gear Ser |
| 1 x | Servo HITEC HS-485 HB |
| 1 x | Servo HITEC HS-7955 TG Coreless Digi |
| 1 x | Plasti Dip Liquid Tape 429 ml black |
| 1 x | Spannlack 1000 ml |
| 1 x | Glider KNIRPS |
| 1 x | X-RAY Micro QR (Fuselage with canopy) |
| 1 x | Aro pasacable Ø20 mm (4 pcs) |
| 1 x | Angle support XT60 conector |
| 1 x | Support Filtro FESTO |
| 1 x | Support ECU Xicoy X-45 |
| 1 x | Motor XPOWER F2919/10 F5J Light |
| 1 x | Actuador lineal HLS12-100210-7.4v |
| 1 x | 2 piece mounting frame |
| 1 x | Support Pitot JETI |
| 1 x | Support conector MPX (6 pcs) |
| 1 x | Recessed MPX connector support (6 pcs) |
| 1 x | Aro pasacable Ø25 mm (4 pcs) |
| 1 x | Soporte grifo FESTO vertical (1 pcs) |
| 1 x | Support pump Xicoy X45 |
| 1 x | Tapa estado carga XT-60 (6 pcs) |
| 1 x | Support Flush MPX Conector (6 pcs) |
| 1 x | Support XT60 conector (2 pcs) |
| 1 x | Soporte filtro FESTO (4 pcs) |
| 1 x | MIG AC 400 /14 |
| 1 x | XPower XC5030/14 LS |
| 1 x | Motor OS 3820-1200 electric |
| 1 x | Motor XPower F2915/12 XLight |
| 1 x | 6,4x1000 mm 2:1 green termoretract tube |
| 1 x | 2,0x50 mm allen screwdriver |
| 1 x | 2 mm female connector (2 pcs) with safety connector |
| 1 x | 105 mm PVC transparent battery termo-retract 68 mm (1 m) |
| 1 x | 0,14 mm PVC servo wire extension, ZH micro conector. |
| 1 x | Servo HITEC HS-65 HB |
| 1 x | wing/fuselage connector for 16 pines AWG 20-24 |
| 1 x | SPARK Switch 5.9v |
| 1 x | Servo HITEC HS-82 MG |
| 1 x | 22 mm Cut Disc Proxxon/Dremmel |
| 1 x | 4,8x1000 mm 2:1 blue termoretract tube |
| 1 x | Glider retract undercarriage 8-16 Kg 2.5-3.2(127 mm wheel) |
| 1 x | 1,2x1000 mm 2:1 red termoretract tube |
| 1 x | Glider retract undercarriage 8-16 Kg 2.5-3.2(140 mm wheel with b |
| 1 x | Retract undercarriage |
| 1 x | 30 cm BEC cable (male) |
| 1 x | 4,8x1000 mm 2:1 black termoretract tube |
| 1 x | 1,2x1000 mm 2:1 black termoretract tube |
| 1 x | 2,5x60 mm allen screwdriver |
| 1 x | Tarjeta programadora RAY G2 |
| 1 x | VIPER JET 2.2m + Electric landig Gear Deco: 01 Red-Blac-kWhit |
| 1 x | Servo HITEC HS-225 MG |
| 1 x | Pins M connect Multipin connectors AWG 20-24 |
| 1 x | Servo lock HS-80/81/82/85 (2 pcs) |
| 1 x | SPARK Switch 12v |
| 1 x | SPS 70V 100/200 A |
| 1 x | SPARK Switch 7.4v |
| 1 x | UBEC 6A KAVAN |
| 1 x | Servo HITEC HS-55 |
| 1 x | Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm) |
| 1 x | Transmitter Cadet 4Ch (V3) 2,4 GHz Mod.2 |
| 1 x | Servo HITEC D941 TW |
 |
| 14,021.81EUR |
.jpg "COMFORT MOUNT ø 25 mm")
