| 2 x | ABS Strip 1.5x4.0x1000 mm |
| 2 x | ABS Strip 1.5x8.0x1000 mm |
| 2 x | Round Rod 5,0x1000 mm |
| 2 x | Strip ABS 2.0x3.0x1000 mm |
| 1 x | Round Rod 1,0x1000 mm |
| 1 x | Round Rod 6,0x1000 mm |
| 2 x | ABS Strip 1.0x3.0x1000 mm |
| 1 x | ABS Strip 1.5x6.0x1000 mm |
| 1 x | ABS I Strip 10x5x1000 mm |
| 2 x | Round Rod 4,0x1000 mm |
| 2 x | Strip 2,0x2,0x330 mm |
| 2 x | Strip 1,5x1,5x330 mm |
| 1 x | ABS Strip 1.5x3.0x1000 mm |
| 2 x | ABS I Strip 20x10x1000 mm |
| 2 x | Round Rod 1,25x1000 mm |
| 2 x | Strip ABS 2.0x10.0x1000 mm |
| 1 x | ABS Strip 1.0x4.0x1000 mm |
| 1 x | ABS Strip 1.0x5.0x1000 mm |
| 1 x | Strip ABS 2.0x5.0x1000 mm |
| 3 x | Round Rod 1,5x1000 mm |
| 1 x | Round Rod 3,0x1000 mm |
| 1 x | ABS Strip 1.0x2.0x1000 mm |
| 1 x | Round Rod 2,0x1000 mm |
| 1 x | DYNAMOMETER S-1580 |
| 1 x | Prolongador S-Bus JR/JR 10cm |
| 2 x | Brass control horn M2 short for wire (2 pcs) |
| 1 x | 6 mm red aluminium threaded horn with patella |
| 1 x | Threaded coupler ALU M3 Ø 6 (2 uds) |
| 1 x | Cable silicona macho batt. receptor 30 cm (Futaba) |
| 2 x | Premium servo extension 25cm |
| 1 x | Brass control horn M4 short for wire (10pcs) |
| 1 x | servo adapter lead, JST-SH socket - JR male Pin, for GR-12SH+HoT |
| 2 x | silicon 100 cm Futaba Extension Ø 0,35 mm |
| 1 x | Futaba male 40 cm extension |
| 1 x | Extension S-Bus 1-2 silicon 120 cm FUTABA |
| 1 x | Horn 5/20 with M2 Bearing |
| 1 x | Extension silicon 30 cm female (Graupner) |
| 1 x | Cable silicona female batt. receptor 30 cm (Futaba) |
| 1 x | Threaded coupler ALU M2,5 Ø 4 (2 uds) |
| 1 x | Cable S.BUS 3 salidas 300 mm |
| 1 x | Extension silicon 10 cm (Futaba) |
| 3 x | Prolongador S-Bus JR/JR 20cm |
| 1 x | Extension silicon 100 cm (Futaba) |
| 1 x | Horn with ball 55x40 |
| 1 x | Threaded coupler ALU M2 Ø 4 (2 uds) |
| 1 x | Extension silicon 30 cm male (Graupner) |
| 1 x | Cabel "Y" 30 cm (graupner) |
| 1 x | Extension 7.5 cm |
| 1 x | Small aluminium horn red (2pcs) |
| 1 x | Cable silicona macho batt. receptor 30 cm (Graupner) |
| 1 x | Circlick securite |
| 1 x | Extension lead 15 cm Multiplex |
| 2 x | Futaba Female 40 cm extension |
| 1 x | Threaded coupler ALU M3 Ø 5 (2 uds) |
| 1 x | RH long aluminium horn (2pcs) |
| 2 x | Profile ABS Square 1 x 1000 mm |
| 1 x | ABS "T" angle 8.0x8.0x1000 mm |
| 1 x | U Profile ABS 5,0x10,0x1000 mm |
| 2 x | Streamline Stainless Steel Tubing 15.5x8.5x1000 mm |
| 1 x | Streamline Stainless Steel Tubing 19.5x9.8x1000 mm |
| 1 x | ABS angle 10,0x10,0x1000 mm |
| 1 x | Streamline Stainless Steel Tubing 6.3x3.5x1000 mm |
| 2 x | Streamline Stainless Steel Tubing 9.0x5.0x1000 mm |
| 1 x | Truck-trailer for gliders 720 x 285 mm |
| 1 x | Angle measurer |
| 1 x | Field folding model stand |
| 2 x | Field folding model stand SebArt |
| 1 x | Propeller balancer |
| 1 x | Truck-trailer for gliders 720 x 239 mm |
| 1 x | Angle of incidence meter |
| 1 x | Remote electric ignition system |
| 1 x | XH female balance (2S) connector (2 pcs) |
| 1 x | Carbon fiber flat 1000x3.0x1.0 mm |
| 1 x | Carbon fiber rod 7.0 mmx1000 mm |
| 1 x | SE Ring 480 mm (2 pcs) |
| 1 x | Cable-Tie 1.66x71mm / 0.07x2.8″ (20 pcs) |
| 1 x | Extension 100 cm (Futaba) |
| 1 x | Sistema LDS - Ø12 mm servos Ø 5/25 spline 60º (KST) pitch 4 mm |
| 1 x | Extension silicon 50 cm (Futaba) |
| 1 x | Extension silicon 30 cm female (Futaba) |
| 2 x | Premium servo extension 50cm |
| 1 x | Extension silicon 100 cm (Graupner) |
| 1 x | Futaba Female 40 cm extension |
| 1 x | Extension silicon 35 cm male (Futaba) |
| 1 x | 200 mm extensión servo HITEC/JR |
| 1 x | ABS Strip 1.5x2.0x1000 mm |
| 1 x | Threaded coupler ALU M3 Ø 4 (2 uds) |
| 1 x | Profile ABS half cane 3x1000 mm |
| 1 x | Profile ABS half cane 8.0x1000 mm |
| 1 x | L-Connector 1.5 mm x 1000 mm |
| 1 x | ZEUS F3A 2m |
| 1 x | Set cintas unión paracaídas 145 cm |
| 1 x | LASER 260 60" V2 ARF Yellow (SkyWing) |
| 1 x | Pilatus PC-21 50E BLUE/WHITE (SebArt) |
| 1 x | Windsock Ozone L - 700 mm |
| 1 x | LUCAS pilot ARTF |
| 1 x | T-Connector 4.0 mm x 1000 mm |
| 1 x | Streamline Stainless Steel Tubing 11.5x6.5x1000 m |
| 1 x | Streamline Stainless Steel Tubing 10.5x5.7x1000 m |
| 1 x | Profile ABS half cane 6.0x1000 mm |
| 1 x | L-Connector 1.0 mm x 1000 mm |
| 1 x | Profile ABS half cane 2.0x1000 mm |
| 3 x | Motor mount for 1 m models |
| 3 x | Indoor motor holder |
| 1 x | |
| 2 x | Size "M" motor holder for class 600 |
| 2 x | Cooler motor type 150 |
| 1 x | Motor brushless 1806 - 2300 Kv Cuadracopter |
| 3 x | Motor holder AXI |
| 2 x | Cooler motor type 400 |
| 3 x | Motor Mount for Multiplex FunJet |
| 2 x | Ø 28 mm fiberglass motor-holder for electric motors |
| 3 x | A50 Motor Mount Alu complete set |
| 2 x | |
| 1 x | Ø 40 mm fiberglass motor-holder for electric motors |
| 3 x | Size "M" motor holder for class 400 |
| 3 x | Cooler motor type 280 |
| 2 x | Receiver bed (Blue) |
| 2 x | Cables suitable for the motor AC 28/7 |
| 2 x | 10 mm gas motor standoff |
| 1 x | Fiberglass motor-holder for electric motors |
| 2 x | Metalic motor holder for class 550-600 |
| 1 x | Electric coversion set |
| 3 x | Disipador para motor Hacker B 20 (or motors up to Ø20 mm) |
| 2 x | Motor holder for AC 28/7 |
| 3 x | A60 Motor Mount Alu complete set |
| 2 x | Fiberglass motor-holder for electric motors |
| 1 x | Central support Speed 600 |
| 1 x | Hacker A30-S Radial Set |
| 3 x | Motor mount for 1200 mm models |
| 2 x | Frontal support Speed 400/480 |
| 1 x | Motor 2212 (1000KV) Quadcopter F450 |
| 1 x | Spinner INOVA 45 mm White |
| 1 x | Spinner INO 89 mm Chrome (Imitacion metal) |
| 1 x | 63 mm INO spinner (carbon imitation) |
| 1 x | Flap hinge (6 pcs) |
| 1 x | Yellow smoke bombs AX-60 (5 pcs) |
| 1 x | Plastic caps for AIR BURTS (30 pcs) |
| 1 x | White smoke bombs AX-60 (5 pcs) |
| 1 x | Rocket D3-P |
| 1 x | Premium servo extension 75cm |
| 1 x | Threaded coupler ALU Left M2,5 Ø 4 (2 uds) |
| 1 x | 82 mm INO spinner (carbon imitation) |
| 1 x | Spinner INO 57 mm Chrome (Imitacion metal) |
| 1 x | Spinner INOVA 102 mm Black |
| 1 x | 38 mm white plastic spinner for fixed propeller / 4,0 mm axi |
| 1 x | Spinner INO 82 mm Chrome (Imitacion metal) |
| 1 x | F3A carbon 75 mm spinner for Hacker C-50 |
| 1 x | Falcon Carbon Spinner 82mm for electric motor |
| 1 x | Canopy Latch |
| 1 x | Aluminium sheet 500x250x0,5mm |
| 1 x | Foam plastic plates (310x210x2 mm) |
| 1 x | Decorative caps, multicoloured, short |
| 1 x | Foam plastic plates (310x210x5 mm) |
| 1 x | Extension S-Bus 1-2 silicon 30 cm FUTABA |
| 1 x | Red smoke canister 100 g |
| 1 x | Blue smoke canister 140 g |
| 1 x | JETImodel Addcap 1640 |
| 1 x | Propadapter for motor A50 |
| 1 x | Connectors banna oro 8,0 mm 5 pcs(Female) |
| 1 x | Shaft for A60-XS-V2 (112,5mm) |
| 1 x | ProgBox PRO LCD Hobbywing |
| 1 x | Carbon tube 3K-PW (L 1000 mm, Ø12 mm, Ø10 mm) |
| 1 x | AXI 2820/12 CYCLONE |
| 1 x | Batería LiPo GENS 5000 mAh 5S 18.5V 60C (Gens Ace) |
| 1 x | Wing tips support for AX-18/AX-60 (2 pcs) |
| 1 x | Rocket D9-7 |
| 1 x | Rocket cardboard tube 50mm x 48mm x 250mm |
| 1 x | 9x4.7 * 22x12 carbon propeller |
| 1 x | Profile ABS half cane 2.5x1000 mm |
| 1 x | Streamline Stainless Steel Tubing 12.3x7.7x1000 mm |
| 1 x | U Profile ABS 1,0x2,0x1000 mm |
| 1 x | White smoke canister 65 g |
| 1 x | Axle for motor A20-S (3 uds) |
| 1 x | Screwdriver for Torx® TX6 |
| 1 x | DUPLEX 2.4EX RC Switch |
| 1 x | Shaft for A60-L (140mm) |
| 1 x | FesEx-Uni8 System |
| 1 x | Backmountset complete A40 |
| 1 x | Shaft for A60-L V4 |
| 1 x | TP/TopFuel - XH 2/3S Adapter |
| 1 x | EDF Stream-Fan 110mm kv780 |
| 1 x | Battery LiFe TopFuel 3100 mAh 3s MTAG 30C |
| 1 x | Shaft for A60-20/22/24S (120 mm) |
| 1 x | Screwdriver for Hexagon 1,5mm |
| 1 x | Axle for motor A50-L |
| 1 x | Cable servo PREMIUM 1 m (blanco/rojo/negro) AWG21 + AWG26 TPE |
| 1 x | Propadapter for motor A50-V3 |
| 1 x | Battery LiFe TopFuel 3100 mAh 4s MTAG 30C |
| 1 x | Battery charging cable XT60 |
| 1 x | A60-6XS V4 28-Pole |
| 1 x | GLOW 9C + accesories |
| 1 x | PowerBox MicroSwitch |
| 1 x | Regulador Hobbywing Platinum 260A HV SBEC V5 |
| 1 x | DC24 II Transmitter case insert |
| 1 x | Electric Landing Gear ULTIMATUM 3.0 (Elektron Re |
| 1 x | SAVAGE Max Red 1080 mm |
| 2 x | Avanti S 1.8m Jet White/Blue + Landing gear |
| 2 x | 7 Servo SET 9g DS MG + Full servo extension cable set for Avanti |
| 2 x | Avanti S 1.8m Jet White/Blue |
| 1 x | Carburetor DLE 170 |
| 1 x | One Way bearing for EME35 starkit with key |
| 1 x | Motor DA 170 |
| 1 x | Air filter MOKI |
| 1 x | Muffler DLE-120 Right |
| 1 x | DLE 85/111/120 Crankshaft keyway |
| 1 x | Motor DA 60 |
| 1 x | Cylinder EME 35 cc |
| 1 x | DA 70 Twin Gas Engine |
| 1 x | EDF Jet-Flex 80 - 8 kg |
| 1 x | RX Battery Eneloop 4,8 V JR 2500 mAh |
| 1 x | Sanyo RX Battery Eneloop 6,0 V JR |
| 1 x | Sanyo TX Battery Eneloop 9,6 V 2500 mAh |
| 1 x | Sanyo Eneloop AA 1,2 V 2400 mAh battery |
| 2 x | Cooler motor type 300 |
| 1 x | Carburettor and crankcase nipple for ZG45SL, ZG62/S/SL and ZG74B |
| 1 x | Fixing Ring with Base 40 mm |
| 1 x | Extra long Prop Bolt for ZG 45/62/74/80, with M5 threaded hole |
| 1 x | Cer clip DA-50R, DA-60 DA-100 DA-100L DA-120, 1 piece |
| 1 x | ZG231cc SHL |
| 1 x | Ignition for DA-35 (without pickup sensor) |
| 1 x | L ELBOW DA-120 normal(2 pcs) |
| 1 x | Carb Carrier, red DA-150L/170 |
| 1 x | Crankshaft DA-120 |
| 1 x | Hifht speed needle DA-50R/100I |
| 1 x | Avanti S 1.8m Jet FREECE TRICOLORI |
| 1 x | BAE HAWK Mini 1.29m MILITARY ARROW ARF +elec.L.Gear + 3 Microser |
| 1 x | Class 30, Red wheel pants (SebART) |
| 1 x | Avanti S 1.8m Jet RED Style |
| 1 x | Avanti S 1.8m Jet FREECE TRICOLORI + Landing gear |
| 1 x | Avanti S 2.3m Jet YELLOW/BLACK & retract (SebArt) |
| 2 x | Bearings for motor HACKER C50 |
| 1 x | Avanti XS Jet , Fuselage Stand (SebArt) |
| 1 x | Avanti S 1.8m Jet FREECE TRICOLORI |
| 1 x | Avanti XS Jet , Exhaust for JetCat P-60/P-140 (SebArt) |
| 1 x | CESSNA 50E White/Red |
| 1 x | Hub propeller DLE 111 V3/120 |
| 1 x | Motor D.A. 200 Magnesium |
| 1 x | Piston ring for DLE-55/111/222 |
| 1 x | Pick up for motor Moki 250 cc 7 cylinders |
| 1 x | Piston ring EME 35cc |
| 1 x | Moki Exhaust Bend 50VT |
| 1 x | DLE 30 complete electronic ignition |
| 1 x | Baffles for Radial Moki S250/330 mm |
| 1 x | Sanyo TX Battery Eneloop 9,6 V Futaba |
| 1 x | Motor Saito FG-36, 36 cc |
| 1 x | 1804 2400KV Brushless Motor Qav 250 mini |
| 1 x | 7 mm gas motor standoff |
| 1 x | O-Ring SAITO FG-60 R3 |
| 1 x | Steel conrod DA-50R and DA-60 |
| 1 x | Rear crankcase DA-50R |
| 1 x | Piston pin for DA-60 DA-120 |
| 1 x | Piston ring for DA-150 |
| 1 x | Compact Silencer KOLM BX-155 |
| 1 x | L ELBOW DA-150 "normal" (2 pcs) |
| 1 x | Piston ring for DA-50R and DA-100 |
| 1 x | ZENOAH ZG 26SC with magneto ignition |
| 1 x | Piston ring for DA-60 and DA-120 |
| 1 x | BAE HAWK Mini 1.29m RED ARROW ARF +elec.L.Gear + 3 Microservos |
| 1 x | Hopper UAT Sebar 600 ml |
| 1 x | Avanti S Jet , Field folding model stand (SebArt) |
| 1 x | Avanti XS Jet , Carrying bags (SebArt) |
| 1 x | Avanti S Jet , Carrying bags (SebArt) |
| 1 x | Avanti XS Jet , Tricolore Canopy |
| 1 x | Avanti S Jet, Kerosene+Smoke Tank(SebART) |
| 1 x | F-104 Starfighter Y/B Aniversary(SebArt) |
| 1 x | BLANIK 50 V2 Silver/Blue (SebArt), cabina |
| 1 x | Avanti XS Jet , Tank for Keroseno (SebArt) |
| 1 x | Hopper UAT Sebar 400 ml |
| 1 x | Electric Landing Gear AVANTIA XS |
| 1 x | 7 Servo SET 9g DS MG + Full servo extension cable set for Avanti |
| 1 x | Avanti S 2.3m Jet WHITE/BLUE (SebArt) |
| 1 x | Avanti S 2.3m Jet YELLOW/BLACK (SebArt) |
| 1 x | Avanti S, Cockpit sunCover (SebART) |
| 1 x | F-104 Starfighter USAF (SebArt) |
| 1 x | Fundas para el transporte F3A alas |
| 1 x | Baffles for Radial Moki S180/320 mm |
| 1 x | Escape DLE-60 Izda |
| 1 x | Tester LiPo/LiIon/LiMn/LiFe |
| 1 x | Escape DLE-60 Dcha |
| 1 x | Motor Moki S 250 cc 5 cyl with autostarter |
| 1 x | Muffler DLE-120 Left |
| 1 x | DLE 55-RA Muffler |
| 1 x | Motor MOKI 160 BVT boxer 4-stroke |
| 1 x | Piston EME 35cc |
| 1 x | Motor Moki 100 BVT |
| 1 x | CDI EME 55/60 cc |
| 1 x | Carburetor DLE 20 |
| 1 x | Muffler DLE 30 |
| 1 x | Piston ring for DLE-20 |
| 1 x | Gasket set DLE-120 |
| 1 x | Piñon motor autostarter 60cc |
| 1 x | Motor EME 60 cc |
| 1 x | One Way bearing for EME55 starkit with key |
| 1 x | Pitts Mufflers EME 70 cc (2 pcs) |
| 1 x | Pitts Mufflers EME 55/60 cc |
| 1 x | Moki Exhaust Bend 200 mm |
| 1 x | EDF Ducted Fan JP Hobby 90mm + 6s Motor 1750Kv (CW) |
| 1 x | Sanyo RX Battery Eneloop 4,8 V JR |
| 1 x | Sanyo RX Battery Eneloop 4,0 V AAA JR |
| 1 x | Sanyo TX Battery Eneloop 7,2 V MPX |
| 1 x | Sanyo Eneloop AA 1,2 V battery 2000 mAh |
| 1 x | Sanyo RX Battery Eneloop RX 4,8 V Futaba |
| 1 x | Sanyo RX Battery Eneloop 6,0 V JR |
| 1 x | Bateria LRP 2200-7.2v 6 cell NiMH |
| 1 x | Sanyo RX Battery Eneloop 6,0 V FUT |
| 1 x | Sanyo RX Battery Eneloop 4,8 V JR |
| 1 x | Sanyo RX Battery Eneloop 6,0 V Futaba |
| 1 x | XT-60 connector (female) |
| 1 x | Central support Speed 280 |
| 2 x | Frontal support Speed 280 |
| 1 x | Size "M" motor holder for class 400 |
| 1 x | Radial heatsink for MPJ AC25/35-xx motor |
| 1 x | Insulator ZG 20 |
| 1 x | Carburator joints for SAITO FA80/80GK/72/72GK |
| 1 x | Header ZG 45/62, "wide" |
| 1 x | Captador OS GT 33 cc |
| 1 x | Motor Mount for TITAN ZG38/38S/38SC, length 36 mm |
| 1 x | Aluminium Motor Mount ZG23SL/H/M and ZG26SC/SCM, ZG231SLH |
| 1 x | Motor NGH GT-17 |
| 1 x | 5 mm gas motor standoff |
| 1 x | Header ZG 45/62, "normal" |
| 1 x | Carburetor menbrane for ZG 20/22/23/26/31 motor |
| 1 x | Motor Saito FG-90 R3, 90 cc |
| 1 x | Cylinder for ZG20 |
| 1 x | 180° TUBE-ANGLE Ø 25 mm |
| 1 x | Ignition for ZG 20/26 |
| 1 x | Carburettor Intake Bend for ZG38 |
| 1 x | 90° TUBE-ANGLE Ø 25 mm |
| 1 x | Crankcase Gasket set for ZG 74 / ZG 80 |
| 1 x | 15 cm PTFE-tubing for 25 mm tubes |
| 1 x | 45 mm gas motor standoff |
| 1 x | OS 40-FG 4T Motor |
| 1 x | Motor ROTO-35 FS BM 4T |
| 1 x | Gasket, insulator ZG 20 |
| 1 x | Air Intake manifold 90° - Large |
| 1 x | RM-85FSI 4-stroke inline gasoline engine |
| 1 x | Carburetor for ZG45SL and ZG62/S/SL |
| 1 x | Captador RCEXL para DA |
| 1 x | Motor Saito FG-60 R3, 60 cc |
| 1 x | 10 mm gas motor standoff |
| 1 x | Escape O-Ring ZIMMERMANN FG-84/90 R3 |
| 1 x | Piston ring for DA-85 and DA-170 |
 |
| 70,727.15EUR |
