| 2 x | DYNAMOMETER S-1580 |
| 2 x | Optical RPM Sensor |
| 1 x | Carbon fiber rod 16 mm x 1000 mm |
| 2 x | Carbon fiber rod 1.5 mm x 1000 mm |
| 2 x | Carbon fiber flat 1000x3.0x1.0 mm |
| 1 x | Carbon fiber rod 2.5 mmx1000 mm |
| 1 x | Carbon fiber rod 7.0 mmx1000 mm |
| 1 x | Carbon fiber rod 5.0 mmx1000 mm |
| 1 x | Carbon fiber rod 10 mm x 1000 mm |
| 1 x | Carbon fiber rod 1.5 mm x 1000 mm |
| 1 x | Carbon fiber flat 1000x3.0x1.0 mm |
| 1 x | Squared carbon wing joinner 5x5x220 mm |
| 2 x | Carbon fiber flat 1000x6.0x0.8 mm |
| 1 x | Carbon fiber rod 0.8 mmx1000 mm |
| 2 x | Carbon fiber rod 1.5 mm x 2000 mm |
| 1 x | Carbon fiber rod 0.5 mmx1000 mm |
| 1 x | Carbon fiber rod 4.0 mmx1000 mm |
| 1 x | Cabel charger transmitter GRAUPNER |
| 2 x | Fast'n EZ-CA-Hinge, lite (12 uds) |
| 1 x | CC 01 |
| 2 x | Nylon hinge 20x15x0,3 (10 pcs) |
| 2 x | Bec MR UBEC 5A (5v/6v/7v) |
| 1 x | 3 copper lacquer wire Ø0,2 mm (1 m) |
| 1 x | Unmounted aluminium pin 6x98 mm (2 pcs) |
| 1 x | 30 cm BEC cable (male) |
| 1 x | Micro flex hinge (12 uds) |
| 1 x | Pin type hinge Al 6x98 mm (2 pcs) |
| 2 x | 3 LiPo XH>EH adapter |
| 1 x | Small pinned hinge (12 uds) |
| 1 x | 67 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs) |
| 2 x | CC 05 |
| 1 x | CC 03 |
| 1 x | Dean "T" - Futaba Adapter |
| 1 x | 2 LiPo XH>EH adapter |
| 1 x | CellPRO 4S Adaptader (GP/KO up to 4S) |
| 1 x | Black copper lacquer wire Ø0,2 mm (5 m) |
| 1 x | Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm) |
| 1 x | 25 mm reinforced hinge |
| 2 x | Flap hinge (6 pcs) |
| 2 x | 33 x 8 mm cylidric hinge Ø 2,5 mm (10 pcs) |
| 1 x | Cylidric hinge 33 mm Ø 2 mm (5 pcs) |
| 1 x | Nylon hinge for flaps 33x9 (2 pcs) |
| 3 x | Nylon hinge 20x20x0,3 (10 pcs) |
| 1 x | Pin type hinge Al 4,5x70 mm demount (2 pcs) |
| 2 x | 30 cm BEC cable (female) |
| 2 x | 43 x 10 mm cylidric hinge Ø 2,5 mm (10 pcs) |
| 1 x | APM2.6 Power module with 5.3V DC BEC |
| 1 x | 48 mm cylidric hinge Ø 2,5 mm (5 pcs) |
| 1 x | Futaba External voltage input cable Futaba CA-RVIN-700 |
| 1 x | TrainerCord (master-learner) |
| 1 x | 5 LiPo XH>EH adapter |
| 2 x | Adapter lead MPX/EC3 |
| 1 x | Pin type hinge Al 3,0x50 mm (2 pcs) |
| 2 x | Long pinned hinge (6 uds) |
| 2 x | Fast'n EZ-CA-Hinge (12 uds) |
| 2 x | MPX-Dean "T" Adapter |
| 1 x | BEC 3A FOXY |
| 1 x | Pin type hinge Al 3,0x50 mm demount (2 pcs) |
| 2 x | Long pinned hinge (12 uds) |
| 3 x | CC 02 |
| 1 x | JETImodel SINGLE BEC |
| 1 x | ABS tube 3.0x1.0x1000 mm |
| 1 x | Aluminium tube (L 1000 mm, Ø7.0 mm, Ø6.1 mm) |
| 1 x | ABS tube 7.0x5.0x1000 mm |
| 1 x | ABS tube 5.0x4.0x156 mm |
| 1 x | Steel tube (L 1000 mm Ø10 mm, Ø9,7 mm) |
| 1 x | Steel tube (L 1000 mm Ø7 mm, Ø6,7 mm) |
| 1 x | Steel tube (L 1000 mm Ø5 mm, Ø4,7 mm) |
| 1 x | ABS tube 5.0x4.0x1000 mm |
| 1 x | CF tube (L 1000 mm Ø0,7 mm, Ø0,3 mm) |
| 1 x | CF tube set (Ø 38 mm y Ø 14 mm) |
| 2 x | ABS tube 12.0x10.0x1000 mm |
| 1 x | Steel tube (L 1000 mm Ø8 mm, Ø7,7 mm) |
| 1 x | ABS tube 18.0x16.0x1000 mm |
| 2 x | ABS tube 8.0x7.0x1000 mm |
| 1 x | ABS tube 16.0x14.0x1000 mm |
| 1 x | ABS tube 8.0x6.0x1000 mm |
| 1 x | Aluminium tube (L 1000 mm, Ø4.0 mm, Ø3.1 mm) |
| 1 x | Steel tube (L 1000 mm Ø12 mm, Ø11,7 mm) |
| 1 x | Aluminium tube (L 1000 mm, Ø5.0 mm, Ø4.1 mm) |
| 1 x | ABS tube 3.0x2.0x1000 mm |
| 1 x | ABS tube 9.0x8.0x1000 mm |
| 1 x | ABS tube 3.0x2.0x330 mm |
| 2 x | ABS tube 10.0x8.0x1000 mm |
| 1 x | ABS tube 9.0x7.0x1000 mm |
| 1 x | ABS tube 6.0x4.0x1000 mm |
| 1 x | ABS tube 20.0x18.0x1000 mm |
| 1 x | Conector AS150 7mm antichispazo (Set: 2 pares) |
| 1 x | XH male balance (3S) connector (2 pcs) |
| 1 x | Banna gold connector 2,5 mm (M/F) |
| 1 x | MPX Sub-D Adaptor |
| 1 x | Connectors banna gold 5,5 mm (M/F) |
| 1 x | Connectors banna oro 8,0 mm (M/F) |
| 1 x | EC5-Set male, simple quality, 2 x female pin, 1 x blue housing |
| 1 x | Banna gold connector 2,5 mm (100 M/F pairs) |
| 1 x | 30 cm DEANS female connector |
| 1 x | Conector BEC female (10 pcs) |
| 1 x | Connectors banna oro 4 mm (M/F) |
| 1 x | 2 mm male connector (2 pcs) with safety connector |
| 1 x | XH male balance (4S) connector (2 pcs) |
| 1 x | Connectors banna oro 2 mm (M/F) |
| 1 x | EC5-Set female, simple quality, 2 x female pin, 1 x blue housing |
| 1 x | Connectors DEANS 4 pins (1 pair) |
| 1 x | XH male balance (2S) connector (2 pcs) |
| 1 x | Gold antispark 5,5 mm plug |
| 1 x | Optotronix Aurora Plug |
| 1 x | Gold antispark 4 mm plug |
| 1 x | Connectors banna oro 6,0 mm (M/F) |
| 1 x | Connectors banana oro 6,0 mm Ultralight (M/F) |
| 1 x | Spikes Band (5 m) |
| 1 x | Wing tips support for AX-18/AX-60 (2 pcs) |
| 1 x | |
| 1 x | BRASS CONTROL HORN M3x16 mm 2pcs |
| 1 x | Ventus 1:4 set of instruments |
| 1 x | Gates hinge 30x16 mm (2 pcs) |
| 1 x | METEOR 1.000 mm kit |
| 1 x | MPX PCB "6 Pins", 5 pieces |
| 1 x | XT-60 connector (female) |
| 1 x | Protector Connector Dean-T (1 pair) |
| 1 x | Carbon fiber rod 1.0 mm x 1000 mm |
| 1 x | Carbon rectangular rod 3.0 mm x 1.0 x 1000 mm |
| 1 x | Carbon fiber rod 8.0 mmx1000 mm |
| 1 x | Carbon fiber rod 6.0 mmx1000 mm |
| 1 x | Carbon wing joinner 13,4 mm Ø 0,48 mm |
| 1 x | Carbon fiber flat 1000x3.0x0.13 mm |
| 1 x | 67 mm cylidric hinge Ø 4,5 mm (5 pcs) |
| 2 x | Canopy hinges for Discus 2c, Discus 2a, Ventus 2cx (2pcs) |
| 1 x | Small pinned hinge (6 uds) |
| 1 x | Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH |
| 1 x | Selfstart electronic switch |
| 1 x | Round flex hinge (12 uds) |
| 1 x | PIX Hawk with accesories |
| 1 x | Walnut wood slat 2.0x2.0x1000 mm |
| 1 x | MR30 connector female |
| 1 x | Mahogany wood slat 2.0x2.0x1000 mm |
| 1 x | 38x4,5 mm wires output (2 pcs) |
| 1 x | Oracover Orange 2 m |
| 1 x | ORACOVER transparent Yellow (10 m) |
| 1 x | Oracover Azul 2 m |
| 1 x | MYLAR film A350 (1000x500 mm) |
| 1 x | Profile ABS half cane 3x1000 mm |
| 1 x | Monokote BLANCO jet (1.8x0.65m) |
| 1 x | ABS "T" angle 6.0x6.0x1000 mm |
| 1 x | Oratex Antik 2m |
| 1 x | Profile ABS Square 1 x 1000 mm |
| 1 x | U Profile ABS 1,0x2,0x1000 mm |
| 1 x | ABS "T" angle 4.0x4.0x1000 mm |
| 1 x | Streamline Stainless Steel Tubing 17.8x12.4x1000 mm |
| 1 x | ABS "T" angle 10.0x10.0x1000 mm |
| 1 x | Oracover Black 10 m |
| 1 x | DUPLEX USBa USB-Adapter for Jeti Duplex Items |
| 1 x | SPARK Switch 7.4v |
| 1 x | PWC4 wing/fuselage connector for 4 servos |
| 1 x | Servo slow down unit (0,7-14,7 sec ) |
| 1 x | 67 mm cylidric hinge Ø 5 mm (4 pcs) |
| 1 x | PSC 6 |
| 2 x | CM-3 |
| 1 x | Gates hinge black 30x16 mm (2 pcs) |
| 1 x | Three-position switched channel, short |
| 1 x | 15 mm reinforced hinge |
| 1 x | USB interface ALTIS |
| 1 x | Opto Gas Engine Kill Switch |
| 1 x | JETImodel Addcap 1640 |
| 2 x | Carbon tube (L 1000 mm, Ø4 mm, Ø2,5 mm) |
| 1 x | Miniature brass strap hinge, 1 m |
| 1 x | Carbon tube 3K-PW (L 1000 mm, Ø14 mm, Ø12 mm) |
| 1 x | PSC 5 |
| 1 x | Cable set PREMIUM, SUB-Done 4three fuselage/wing 160 cm |
| 1 x | Thinwall Stainless Steel Tubing 28x0.6x1000 mm |
| 1 x | Extension 2/3 lipos JST - JST/C |
| 1 x | Carbon tube 3K-PW (L 1000 mm, Ø19 mm, Ø15 mm) |
| 1 x | Copper lacquer wire Ø0,2 mm (5 m) |
| 1 x | Pin type hinge Al 4,5x70 mm (2 pcs) |
| 1 x | ABS tube 2.0x1.0x1000 mm |
| 1 x | Nylon hinge 15x0,3 (10 pcs) |
| 1 x | ABS tube 6.0x5.0x1000 mm |
| 1 x | Carbon tube (L 1000 mm, Ø12 mm, Ø10 mm) |
| 1 x | Connector Sub-D 2+5 Female |
| 1 x | Conector FUTABA Servo male (10 pcs) |
| 1 x | Conector JAPAN G2 Set 5 pares |
| 1 x | Wing connector 8pin with pin strip, plug & socket |
| 1 x | Connector CAN 15 |
| 1 x | Carbon tube 3K-PW (L 1000 mm, Ø8 mm, Ø6 mm) |
| 1 x | Hard brass tubing (L 1000 mm, Ø3.0 mm, Ø2.1 mm) |
| 1 x | Connectors banna oro 3 mm (M/F) |
| 1 x | Sun Cover ULTIMATUM 2.0 (Hispano Aviacion) |
| 1 x | Sun Cover BULL Mo1 2.6 (Hispano Aviacion) |
| 1 x | Oracover ROYAL RED 2m |
| 1 x | Carbon fiber rod 0.5 mmx1000 mm |
| 1 x | Propeller CFK 11x8 |
| 1 x | Propeller MEJZLIK 20x10 Electric light (36 g) |
| 1 x | Gates hinge |
| 1 x | Battery RX JETI LiIon RB 5200 7.2v |
| 1 x | DUPLEX 2.4 EX MBar |
| 1 x | DUPLEX 2.4EX RC Power Switch 10 |
| 1 x | Aluminium cap bolt washer M3 green (8 pcs) |
| 1 x | Straightened threaded rod M3 - 1m |
| 1 x | AL Axle Shaft 4.0x16 mm (2 uds) |
| 1 x | Lite Plywood panel 600x300x2.0 mm |
| 1 x | Carbon tube (L 1000 mm, Ø6 mm, Ø4 mm) |
| 1 x | Kwik link AL M4 con Clip (2 pcs) |
| 1 x | Blue metalic ball link M2/2 azul (2 pcs) |
| 1 x | Antenna Hole Cap V1 (Silver) |
| 1 x | Avanti S Jet , Carrying bags (SebArt) |
| 1 x | Avanti S 2.3m Jet YELLOW/BLACK (SebArt) |
| 1 x | aluminium servo arm V1-JR 1,0 inch M2 |
| 1 x | Aluminium red ball links M3 V1 (10 pcs) |
| 1 x | Avanti S 2.3m Jet WHITE/BLUE (SebArt) |
| 1 x | Interface Jack Adapter IKARUS |
| 1 x | BU 131 Jugmann Panel Instrum. frontal |
| 1 x | PARTENAVIA 2020 mm ARF with Flaps |
| 1 x | LO 100 ARC 3.3m,frame canopy |
| 1 x | ESC Ripmax QUANTUM 80A SBEC |
| 1 x | "Y" charging 4mm wire (2 IN-1 OUT). |
| 1 x | Interruptor RX/Batterie |
| 1 x | 18 mm reinforced hinge |
| 1 x | Carbon tube (L 1000 mm, Ø2 mm, Ø1 mm) |
| 1 x | Carbon fibre tube -TAPERED- 3k-PW (10 x 5 x 0.3) x 880 mm |
| 1 x | ABS tube 5.0x3.0x1000 mm |
| 1 x | PWC6 PowerWingConnector for 6 servos with fuselage socket |
 |
| 10,379.17EUR |
