| 1 x | 28x5 mm wires output (2 pcs) |
| 3 x | Allen wheel collar M4x4 |
| 1 x | Clip mini fixing for wing (2 pcs) |
| 1 x | Aluminum Bayonet / strongal D12 mm / 0.5 m |
| 3 x | 100 mm rods + T patellas set for direction control |
| 1 x | 11 mm Rubber pads (14 pcs) |
| 1 x | Aluminun wheel collar 6 mm Ø (4 uds) |
| 2 x | 38x4,5 mm wires output (2 pcs) |
| 2 x | Cabin latch Fox MDM1 4m (pair) |
| 2 x | Allen wheel collar M3x5 |
| 1 x | Canopy Lock V1 M3 Blue (2 pcs) |
| 1 x | Aluminun wheel collar 4 mm Ø (4 uds) |
| 2 x | Canopy Lock V1 M3 Red (2 pcs) |
| 1 x | Aluminun wheel collar 2.5 mm Ø (4 uds) |
| 3 x | Aluminium alloy coupler for carbon tube 6/M4 |
| 3 x | Cable grommet 9.5 mm (4 uds) |
| 3 x | Cable grommet Ø 5 mm (4 uds) |
| 3 x | Allen wheel collar M3x3 |
| 1 x | 80 mm rods set for direction control |
| 2 x | Cap closure 33/23.5mm (2 uds) |
| 2 x | 45 mm rods + T patellas set for direction control |
| 2 x | 250 mm / 16 mm Airbrakes |
| 1 x | Aluminun wheel collar 2 mm Ø (4 uds) |
| 2 x | 100 mm rods set for direction control |
| 2 x | Cable grommet Ø 3.2 mm (4 uds) |
| 2 x | Allen wheel collar M4x6 |
| 3 x | Aluminun wheel collar 3.5 mm Ø (4 uds) |
| 1 x | Cockpit aluminium closing |
| 3 x | 140 mm rods set for direction control |
| 1 x | Aluminum Bayonet / strongal D25 mm / 1 m |
| 1 x | Optical RPM Sensor |
| 2 x | DYNAMOMETER S-1580 |
| 2 x | Extractor piñones 2.3/3.2 mm |
| 3 x | Servo NARO Max Std |
| 1 x | Simulador RealFlight RF-9.5 S (sin emisora) |
| 1 x | SIMtransmitter 6 Mode 2 |
| 1 x | Hovercraft sailcloth |
| 1 x | |
| 1 x | Steering arm 16 mm Ø 3 mm (2 uds) |
| 1 x | Steering arm 16 mm Ø 4 mm |
| 1 x | Split pin 1.6x16 mm (10 uds) |
| 1 x | Split M1,2x10 (10 pcs) |
| 1 x | Clip fixing for wing (2 pcs) |
| 1 x | Lead with adhesive (2 pcs) |
| 1 x | Crimping sleeves for cable 0.85 mm (10 pcs) |
| 1 x | 45 mm rods set for direction control |
| 2 x | Aluminun wheel collar 3 mm Ø (4 uds) |
| 2 x | Cierre cabina aluminio Ø5, I=16 mm |
| 1 x | Cable grommet Ø 6.4 mm (4 uds) |
| 1 x | Cable tie mounts 4.3 (4 uds) |
| 1 x | Tip wing protector 40x14 (2 pcs) |
| 1 x | Landing gear frontal support 29x26x13,5 |
| 1 x | Tip wing protector 28x10x12 (2 pcs) |
| 1 x | Micro screw-lock pushrod conn snap Ø 1 mm (2 uds) |
| 2 x | Cable grommet Ø 4 mm (4 uds) |
| 1 x | Steering arm 12 mm Ø 4 mm |
| 1 x | Steering arm 12 mm Ø 4 mm (2 uds) |
| 1 x | Cierre cabina aluminio Ø4, I=10 mm |
| 1 x | Aluminun wheel collar 5 mm Ø (4 uds) |
| 2 x | 90 mm rods + T patellas set for direction control |
| 2 x | Locking cable tie 2.5x100 (uds) |
| 1 x | Canopy Latch |
| 2 x | Snap long M2 (10 uds) |
| 2 x | 140 mm rods + T patellas set for direction control |
| 3 x | Screw-lock pushrod conn snap Ø 1.5 mm (2 uds) |
| 1 x | Circlick securite |
| 1 x | Lock washer 2.7 mm (20 pcs) |
| 1 x | Pilot "Adolf" Legends Series (Slimline) |
| 2 x | Wing bolts M6 Steel screw Red (2 pcs) |
| 1 x | Threaded coupler ALU M2,5 Ø 4 (2 uds) |
| 1 x | Opale Rucksack |
| 1 x | Universal Colour Paste signal white (RAL 9003) 1 Kg |
| 1 x | Wing-connector: Glass / Carbon tube (26.5/25 x 25/23) x 1000 mm |
| 1 x | 10 mm Quick clamp_L (6 pcs) |
| 1 x | aluminium servo arm V2-JR 2,0 inch M3 |
| 2 x | Antenna Hole Cap V1 (Silver) |
| 1 x | Soporte grifo FESTO vertical (1 pcs) |
| 1 x | 6 mm Quick clamp_S (10 pcs) |
| 1 x | 30 mm gas motor standoff |
| 1 x | 10 mm floating pad (72 pcs) |
| 1 x | Support hands Issuer PROFI TX |
| 2 x | DUPLEX 2,4EX Stick with Potentiometer for Transmitter DC/DS |
| 2 x | Antenna FUTABA 2.4GHz 3PM/8FG/14SG/18SZ/18M |
| 1 x | Harness for transmitter JETI DUPLEX |
| 1 x | Charger HITEC CG-42 TX 7.2v/ RX 4.8v (80 mA) |
| 1 x | Arnes cruzado Confort de Luxe PROFI |
| 1 x | Winter-Glove DS tx |
| 1 x | Tray FUTABA T6K,T10J,T12K,T14SG,T16iZ,T18SZ,T18MZ,T32MZ |
| 2 x | EnLink 2RS Plus - DUO |
| 1 x | Maleta transporte FUTABA 10PX |
| 1 x | Tray for FUTABA 14SG/16SZ |
| 1 x | Decorative caps, multicoloured |
| 2 x | Switch Nutspanner for JETI Duplex Transmitter DC / DS |
| 1 x | PPM to Jack link - Tx Black (mono) DC/DS Tx DUPLEX 2,4EX |
| 1 x | Switch for DS: Long 3 Position |
| 1 x | Teacher-student connector T12FG/FX-30 |
| 1 x | Switch moment button, 2 functions, long FUTABA |
| 1 x | RC Power Switch 5A |
| 2 x | Transmitter JETI Duplex DC-24 EX Carbon Line Multimode |
| 1 x | Duplex 2.4EX tray transmitter DC-16 II Black multimode |
| 1 x | Pushrod greyline 4/3 with coupler M3 |
| 1 x | Receiver FrSKY Archer R8pro 2,4 Ghz |
| 1 x | JETI handheld transmitter DS-14 II Blue Multimode |
| 1 x | Transmitter JETI Duplex DS-24 EX Carbon Line Dark BLUE Multimod |
| 1 x | Stickers-digit for marking |
| 1 x | Locking cable tie 3.2x142 (uds) |
| 1 x | Adapter 3,0 mm M6 for spinner 40 mm fixed propeller |
| 1 x | Threaded coupler ALU M2,5 Ø 6 (2 uds) |
| 1 x | Threaded coupler M2,5 Ø 2 mm (10 pcs) |
| 1 x | Lense for Spotlights, 20mm |
| 1 x | Threaded coupler ALU Left M2,5 Ø 4 (2 uds) |
| 1 x | Combo lighting module with covering drop shape |
| 1 x | Threaded coupler M2 (10 uds) |
| 1 x | 8Wx2 Navigation & Strobe, 11mm, T-Fuse Red/White |
| 1 x | Aluminum Bayonet / strongal D35 mm / 1 m |
| 1 x | Adapter 3,2 mm M8 |
| 1 x | 6 mm red aluminium threaded horn with patella |
| 1 x | 16mm Gear-Spotlight, 4W |
| 1 x | Threaded coupler ALU M3 Ø 4 (2 uds) |
| 1 x | Threaded coupler ALU M2,5 Ø 3 (2 uds) |
| 1 x | 2000A 12V Lithium Jump Starter with 150PSI Air inflator |
| 1 x | Couple M4 for wire (10 pcs) |
| 1 x | Threaded coupler ALU Left M3 Ø 4 (2 uds) |
| 1 x | Threaded coupler ALU M3 Ø 5 (2 uds) |
| 1 x | Heat sink for Optotronix LEDs |
| 1 x | RF9 Flight Simulator with Spektrum Controller |
| 1 x | Jet Afterburner Simulator NF-Jet3 RY |
| 1 x | LED wire (white - 2pcs) |
| 1 x | Fully Threaded Steel Rod Duralumin 50 mm M3 (2 pcs) |
| 2 x | Wheel collar 2 mm Ø (4 uds) |
| 1 x | Fully Threaded Steel Rod M2,5 (2 uds) |
| 1 x | Steering arm 12 mm Ø 3 mm (2 uds) |
| 1 x | Fully Threaded Steel Rod alumin 90 mm M3 (2 pcs) knurled |
| 1 x | Fully Threaded Steel Rod Duralumin 70 mm M3 (2 pcs) |
| 1 x | Tip wing protector 30x10 (2 pcs) |
| 2 x | Interface Jack Adapter IKARUS |
| 1 x | Pushrod greyline 3/2 with coupler M3 L: 1000 mm |
| 1 x | Switch Cap L (Red) |
| 2 x | Switch Cap M (black) |
| 1 x | wire tensioner (red) |
| 1 x | Transmitter Balancer Futaba FF9-DX7-JR-Hitec |
| 2 x | Transmitter Stick Ends V5 Rojo - M3 Futaba/Hitec/Spektrum DX8 (2 |
| 2 x | Transmitter Stick Ends V4 Blue/Silver - M3 (2 pcs) |
| 1 x | Fuel line plugs (Black) |
| 2 x | Transmitter Stick Ends V5 Red - M4 JR/DX7 |
| 2 x | Transmitter Stick Ends V2 Red - M3 (2 pcs) |
| 1 x | Connectors MPX male |
| 1 x | Neck strap JETI DC |
| 2 x | Switch Spring-Loaded 2-Position DC Tx DUPLEX 2,4EX |
| 1 x | switch long 3-position DC Tx DUPLEX 2,4EX |
| 1 x | Transmitter Stick Ends V1 Blue - M3 (2 pcs) |
| 2 x | Switch Cap L (Blue) |
| 1 x | Wing bolts M6 Steel screw Blue (2 pcs) |
| 1 x | Transmitter Stick Ends V1 Red - M3 (2 pcs) |
| 1 x | TX-Tray V1 (L) (Black) |
| 2 x | Switch Cap M (silver) |
| 1 x | Switch Cap M (blue) |
| 1 x | Transmitter Stick Ends V3 Red - M3 (2 pcs) |
| 2 x | Transmitter Balancer SPK DX-8 |
| 2 x | Transmitter Stick Ends V4 Blue- M3 (2 pcs) |
| 2 x | Transmitter Stick Ends V5 Blue - M4 JR/DX7 |
| 1 x | Wheel 38 mm V2 |
| 1 x | wire tensioner (silver) |
| 1 x | wire tensioner (black) |
| 1 x | Transmitter Stick Ends V5 Blue - M3 Futaba/Hitec/Spektrum DX8 (2 |
| 1 x | T- Fittings red color (2pcs) |
| 1 x | T- Fittings blue color (2pcs) |
| 1 x | Transmitter Balancer HITEC Aurora 9, JR and Spectrum (blue) |
| 1 x | Switch Cap L (black) |
| 1 x | Wing bolts M3 Steel screw blue (2 pcs) |
| 1 x | Fully Threaded Steel Rod Duralumin 100 mm M3 (2 pcs) |
| 1 x | Fuel dot Gold color |
| 1 x | Fuel dot blue |
| 1 x | Fuel dot V3 (Red) |
| 2 x | Fully Threaded Steel Rod Duralumin 120 mm M3 (2 pcs) |
| 1 x | Suction funnel for carburetor WALBRO 20-80cc (blue) |
| 1 x | Refueling Cap V3 (RED) |
| 1 x | Fully Threaded Steel Rod Duralumin 110 mm M3 (2 pcs) |
| 1 x | Check valve V2 |
| 1 x | Fuel dot V3 (Black) |
| 1 x | Fuel dot V3 (Silver) |
| 1 x | Suction funnel for carburetor WALBRO 20-80cc (red) |
| 1 x | Suction funnel for carburetor DA70- MVVW 190cc (red) |
| 1 x | switch 1-Spring-UP 3-position DS Tx DUPLEX 2,4EX |
| 1 x | Switch Button DS Tx DUPLEX |
| 1 x | Battery Lipo GENS 4000 mAh 7.4v TX |
| 1 x | Battery LiPo GENS 4400 mAh 7S 25.9v 35C (Gens Ace) |
| 1 x | JETI Counter for DC-16 (Blue) |
| 1 x | switch short 3-position DS Tx DUPLEX 2,4EX |
| 1 x | Teacher / Student Cable |
| 1 x | Receiver bed (Blue) |
| 1 x | Battery LiPo GENS 450 mAh 2S 7.4V 25C (Gens Ace) |
| 1 x | Three-function control switch by FUTABA |
| 1 x | Battery LiPo GENS 160 mAh 2S 7.4V 30C (Gens Ace) |
| 1 x | Hand Pads for Tray JETI |
| 1 x | JETImodel DPS 40 |
| 1 x | Antena FUTABA 35 mhZ 3PM/3FRF/4V/4Y/6EX/6X/6Y/7C |
| 1 x | Transmitter JETI Duplex DS-12 EX Multimod BLUE |
| 1 x | Emisora JETI Duplex DS-16 II Carbon Line YELLOW |
| 1 x | Black tray 2,4EX DC-16/14/24 black |
| 1 x | Switch for DS: Short 2 Position |
| 1 x | Tray JETI for DS-14/16/24 Black |
| 1 x | Emisora JETI Duplex DS-12 EX Special Edition "Carbon Purple" |
| 1 x | PPM to Jack link - Tx Red (stereo) DC/DS Tx DUPLEX 2,4EX |
| 1 x | Transmitter JETI Duplex DS-24 EX Multimode |
| 1 x | Futaba Aero Large Case - Internal Foam |
| 1 x | Tx JETI Duplex DC-24 II Carbon Line Ruby |
| 1 x | Aceite turbina JetsMunt 1 litro |
| 1 x | DJI Mavic Air Fly More Combo |
| 1 x | Triple rod con. 3mm Pushrod (2 pcs) |
| 1 x | FALCON 29X9 CARBON PROPELLER (GAS) |
| 1 x | Propeller MENZ-S 18x6 |
| 1 x | FALCON 27X11 CARBON PROPELLER (GAS) |
| 1 x | Propeller MENZ-S 17x6 |
| 1 x | |
| 1 x | Futaba 52 mm servo arm |
| 1 x | Futaba 38 mm servo arm with ball link |
| 1 x | 5 mm Prop Adapter M6 |
| 1 x | Resistor 3W 5% OR82 |
| 1 x | Futaba 50/60 mm servo pull-pull double arm with ball link |
| 1 x | LED blink wire flashing (red - 2pcs) |
| 1 x | ED Position Lights wireless (Set of 3) |
| 1 x | Winter Glove for DC |
| 1 x | Stick with Button DC/DS-16/14/24 Tx DUPLEX 2,4EX |
| 1 x | Combo AM480 T-Motor 650 Kv |
| 1 x | Turnbuckle M2x22/35 (2pcs) |
 |
| 24,249.05EUR |
