36.16EUR

Epoxy Casting Resin + Hardener "water-clear" (300 min)
[R1071023]


Epoxy Casting Resin + Hardener "water-clear" (300 min)

General information about the System Epoxy Casting Resin + Hardener "water-clear):
Two-component clear, colourless epoxy system.
The following properties distinguish it from the predecessor EP cast resin “crystal clear”:
Excellent UV resistance for epoxy resins*)
Supertransparent constituents
Polishable, hard surface
Excellent impact strength
Completely tackfree curing even in thin coats
Ideal for transparent coatings
Also suitable as a laminating resin system with a very long pot life
The system's reactivity was raised for smaller initial and casting quantities. An initial batch size of 400 g can be cast per mould without the surface collapsing. Casting thicknesses up to 40 mm are possible with larger initial quantities.

Like all reactive resin systems the casting quantity is limited by the generated reaction heat (exothermal reaction): often a lower curing temperature (e.g. at an ambient night temperature lower than 20 °C) can counteract too great an exothermal reaction.

Pot life : approx. 300 minutes

Mixing ratio:
100 : 37 parts by weight of resin to hardener
100 : 47 parts by volume of resin to hardener

Curing time: approx. 24–48 h

Processing:
Resin and hardener are homogenised for about two minutes at room temperature (23 °C). Afterwards the mixture is left to rest for approx. 20 minutes.
Leave the ready mixture on a flat surface for 48 hours. Please do not mix or otherwise move the product. The total curing time ranges from 24 to 48 hours.
Expertise for the resin system casting resin + hardener "water-clear": this system is not cytotoxic (cell damaging), important for applications in medical purposes!
*) This system has very good UV resistance for EP resins, but, like all epoxy resins, it can turn more or less yellow over time under high UV exposure. Therefore only conditionally suitable for outdoor applications or permanent exposure to artificial light sources.
Typical areas of application: Indoor: railway models, works of art, stage decorations, etc. (only occasionally exposed to UV sources).


temporarily out of stock
temporarily out of stock

Reviews
Categories
* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->
  
  3D IMPRESION
  ABS Rods-Strips
  ABS/GFK/CFK plate
  Actuator
  Adapters->
  Adhesives/Resin/Epoxy->
    Cianocrylate->
    Epoxy->
      EMC-Vega
      KAVAN
      Loctite
      Resoltech
      Epoxy BSI
      Epoxy R-G
    Resin/Gelcoat
    Glass Bubbles
    Contact adhesive
  Altimeters->
  Amperimeters
  Anemometer
  Auto-Pilot
  Bags/Covers
  Batteries->
  BEC/Cables/Conectors/Interruptor
  Bungee Launchers
  Cables
  Cameras->
  Carbon rod
  Carbon/Brass/Steel/ABS/Aluminium
  Catalogues
  Chargers->
  Clevis
  Combustible->
  Connectors
  Control horns
  Controlers->
  Coverings/Thermoretrac
  Decals
  Extension
  Extinguisher
  Ferritas
  Glasses
  Hardware
  Hinges
  Instruments / Panels
  Lights/Ilumination->
  Linkages
  Merchandising
  Motor
  Pilots
  Pinion extractor
  Power supply system/Data Recordi->
  Profiles
  Propelers->
  Screws
  Servos->
  Simulators
  Smoke/Rocketry/Fireworks
  Spinners->
  Spray/Painting/Dope/Solder Paste
  Steel/brass Rod/Aluminium
  Support/CG/Incidenc.
  Tapes/Closed/Bridles
  Tools
  Towing
  Transmitters/Receivers->
  Undercarriage->
  Wheels & Axles->
  Wing Joiner
  Wood
Car/Trucks->
Motors & Turbines->
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
2 x 80 mm rods set for direction control
2 x Allen wheel collar M3x3
1 x Aluminun wheel collar 3.5 mm Ø (4 uds)
2 x Cockpit aluminium closing
2 x Aluminun wheel collar 2.5 mm Ø (4 uds)
3 x Canopy Lock V1 M3 Blue (2 pcs)
1 x Aluminun wheel collar 3 mm Ø (4 uds)
2 x Aluminun wheel collar 2 mm Ø (4 uds)
1 x Cable grommet Ø 5 mm (4 uds)
2 x Clip mini fixing for wing (2 pcs)
1 x 28x5 mm wires output (2 pcs)
1 x Cable grommet Ø 4 mm (4 uds)
1 x Aluminun wheel collar 4 mm Ø (4 uds)
2 x Allen wheel collar M4x4
2 x Allen wheel collar M4x6
1 x 45 mm rods + T patellas set for direction control
2 x Cable grommet Ø 6.4 mm (4 uds)
1 x 140 mm rods + T patellas set for direction control
2 x Cable grommet 9.5 mm (4 uds)
1 x 140 mm rods set for direction control
1 x 250 mm / 16 mm Airbrakes
3 x 38x4,5 mm wires output (2 pcs)
1 x Cable grommet Ø 3.2 mm (4 uds)
2 x Aluminun wheel collar 6 mm Ø (4 uds)
1 x Cable tie mounts 4.3 (4 uds)
2 x Clip fixing for wing (2 pcs)
1 x Militarian pilot "Fly Boy" size 9cm (Slimline)
1 x Militarian pilot "Kamikaze" size 9cm (Slimline)
1 x Civilian pilot "Gramps" size 9cm (Slimline)
1 x Pilot WWII US Navy Pacific 12" Scale 1/6-1/5
1 x Piloto JET 1:3,5
2 x Civilian pilot "Pamela" size 9cm (Slimline)
1 x 1/10 Pilot "Jimmy"
1 x Civilian pilot "Joe" size 9cm (Slimline)
1 x Pilot "Anthony" (Slimline)
1 x Pilot JAN 1/4 Saiplanes
1 x 1/10 Pilot "Jack"
1 x 1/7 Pilot "Japanese"
1 x 1/4 Pilot "Mike"
1 x 1/6 Pilot "John"
1 x Pilot "Adolf" Legends Series (Slimline)
1 x 1/6 Pilot "Tony"
1 x 1/6 Pilot "Garry"
1 x Civilian pilot "Curt" size 9cm (Slimline)
1 x Pilot "Duke" Legends Series (Slimline)
1 x Piloto jet 130 mm
2 x Big-Malibu XL Roof box with surfboard rack GREY
2 x Tube Pitot to PIXHAWK
2 x Digital Air Speed Sensor And Pitot Tube Set
1 x 11 mm Rubber pads (14 pcs)
1 x Sandwich carbon + poplar 3mm + carbon 290x160 mm
1 x Cabin latch Fox MDM1 4m (pair)
2 x Cierre cabina aluminio Ø5, I=16 mm
1 x Propeller APC 14x8.5 Electric Pusher
1 x FALCON 20X9 CARBON PROPELLER (GAS)
1 x 100 mm rods set for direction control
1 x 41x5,5 mm wires output (2 pcs)
1 x "S" set for planes
1 x "M" set
1 x White smoke bombs AX-3 (10 pcs)
2 x Green smoke canister 100 g
2 x Parachutist
2 x Remote electric ignition system
2 x Mixers smoke bombs AX-60 (5 pcs)
1 x Smoke set "M"
1 x Ventral support for AX-18/AX-60
1 x Yellow smoke bombs AX-60 (5 pcs)
1 x Green smoke canister 65 g
1 x Red smoke canister 65 g
2 x "S" set for boats
2 x Fully Threaded Steel Rod alumin 80 mm M3 (2 pcs)
1 x Solvent Plasti Dip 1000 ml
1 x Fully Threaded Steel Rod alumin 90 mm M3 (2 pcs)
3 x Crimping sleeves for cable 0.85 mm (10 pcs)
1 x Fully Threaded Steel Rod Duralumin 70 mm M3 (2 pcs)
2 x Cockpit aluminium closing 5.4g
1 x Fully Threaded Steel Rod alumin 100 mm M3 (2 pcs)
1 x 500 ml sealer (DOPE)
1 x 
1 x Spray Graphit 33
1 x Spray YELLOW Inca Lexan 150ml
1 x Fully Threaded Steel Rod alumin 100 mm M3 (2 pcs)
1 x Partall paste 650 g
1 x Fully Threaded Steel Rod alumin 60 mm M2,5 (2 pcs)
2 x Spray EC Red 400ml
1 x Fully Threaded Steel Rod alumin 90 mm M2,5 (2 pcs)
1 x Crimping sleeves for cable 0.70 mm (10 pcs)
1 x Fully Threaded Steel Rod Duralumin 40 mm M3 (2 pcs)
1 x Silicone adhesive ELASTOSIL® E4, tube/ 90 ml
1 x Cockpit plastic closing
2 x Crimping sleeves for cable 1.3 mm (10 pcs)
1 x Plasti Dip Liquid Tape 429 ml black
1 x Universal Colour Paste white 50 g
2 x Universal Colour Paste deep black 250 g
1 x Fully Threaded Steel Rod Duralumin 120 mm M3 (2 pcs)
1 x Presto SF Light Filler styrene-free (420 g)
1 x Paint gun for sprays
1 x Painting GHT Lexan Black 150 ml
1 x Fully Threaded Steel Rod alumin 40 mm M3 (2 pcs)
2 x Cockpit metalic closing
2 x Covered closure or fairings
1 x Fully Threaded Steel Rod Duralumin 34 mm M3 (2 pcs)
1 x Canopy Latch
1 x Rubber profile 8-2 mm 2M
1 x ABS rectangular profile 10x5.0x1000 mm
1 x Flap hinge (6 pcs)
1 x Balsa panel 10x100x1000 mm
1 x Balsa panel 5.0x100x1000 mm
1 x BRASS CONTROL HORN M3x16 mm 2pcs
1 x 1/12 Pilot "Langley"
1 x Canopy Lock V1 M3 Red (2 pcs)
1 x Support XT60 conector (2 pcs)
1 x Angle support XT60 conector
1 x 1/12 Pilot "Fighter"
1 x Piloto Jet "Green" 1/6 Scale
1 x 1/12 Pilot "Cougar"
1 x Actuador lineal HLS12-100210-7.4v
1 x Piloto Jet "Red" 1/6 Scale
1 x Conector MT-60 (pair)
1 x Battery LiPo GRE18 600 mAh 7.4v
1 x Adaptadores carga 6s JST-XH
1 x Ball Link M2 with Ball and Hardware, 10 pcs
1 x Swashplate metal LAMA
1 x Fully Threaded Steel Rod Duralumin 130 mm M3 (2 pcs)
1 x 
1 x Cockpit latch closing I=10 mm
2 x Universal Colour Paste signal white (RAL 9003) 1 Kg
1 x Ball Link Plier
1 x Xplorer4 anemometro
1 x Bateria LRP 2200-7.2v 6 cell NiMH
1 x Aro pasacable Ø20 mm (4 pcs)
1 x Electric spoiler 250 mm (2 pcs)
1 x Aluminium alloy coupler for carbon tube 6/M4
1 x Tip wing protector 40x14 (2 pcs)
1 x Fully Threaded Steel Rod alumin 30 mm M3 (2 pcs)
1 x Split pin 1.6x16 mm (10 uds)
1 x Servo GO-1035MG 16 kg.cm 0.08s/60º
1 x Snap for floding prop for 2 mm axi
1 x Fully Threaded Steel Rod alumin 60 mm M3 (2 pcs)
1 x Split M1,2x10 (10 pcs)
1 x EXTRA NG 74" yello/blue/red (Skywing RC)
1 x Screw-lock pushrod conn snap Ø 1.5 mm (2 uds)
1 x Motor SAITO FG-61 TS
1 x Piloto RC Civil 1/5- 1/6 Scale 12"
1 x Split pin 1x8 mm (10 uds)
1 x Cockpit aluminium closing 4.7g
1 x 1/4 Pilot "Heidi"
1 x Conector MR-60 (pareja)
1 x Steering arm 16 mm Ø 4 mm
1 x Snap short M2 (10 uds)
1 x Tren retractil ULTIMATUM 1.5 combo ER30 SEt B (ControlBox)
1 x Locking cable tie 2.5x100 (uds)
1 x Allen wheel collar M3x5
1 x Pilot "Goose" (Slimline)
1 x White smoke canister 65 g
1 x Black smoke bombs AX-60 (5 pcs)
1 x Pushrod octagone 3/2
1 x Smoke set "Glider"
1 x Screw-lock connector Ø 2 mm (2 uds)
1 x Pushrod greyline 3/2 with coupler M3 L: 1000 mm
1 x Straightened rod Ø 0.8 mm x 1000 mm
1 x PT 22x10 EL Propeller
1 x Red smoke bombs AX-60 (5 pcs)
1 x 1000 ml sealer (DOPE)
1 x Epoxy Resin L + Hardener LT kit/ 3125g
1 x Epoxy Resin L + Hardener L (40 min) 1Kg (715g Resin L + 285g Har
1 x Epoxy 40 min (Resin). 25Kg
1 x Epoxy 40 min (Resin). 5 Kg
1 x Epoxy adhesivo Elan-tech ADH 981.892 50ml (dark grey)
1 x Epoxy 30 min. 200g
1 x Epoxy L 40 min. 10 kg (Resin)
1 x Epoxy L 40 min. (1 Kg) 715g Resina / 285g Hardener S (15 min)
1 x Epoxy 40 min. 4kg (Hardener)
1 x Epoxy Casting Resin + Hardener "water-clear" (300 min)
1 x Epoxy 10 min 190g
1 x Epoxy 5 min. 500 g (Resin)
1 x Epoxy Resin L + Hardener GL 1 (30 min)
1 x Epoxy Resin HT 2 + Hardener HT 2, kit/ 296 g
10,711.25EUR
Manufacturers
Manufacturer Info
R-G.de
R-G.de Homepage
Other products
Languages
Español English
Currencies