29.90EUR

Mould Resin P + Hardener EPH 161-P, kit/ 585 g
[R1151570]


Mould Resin P + Hardener EPH 161-P, kit/ 585 g

Hard elastic, good edge strength
Excellent grinding and polishing properties
Thixotropic (non-drip)
Manufactured in vacuum, so optimally free of air bubbles and homogeneous
This epoxy resin is coloured black for gelcoats (applied thickness 0.5–1 mm) in mould construction with high edge strength and good polishing properties.

In combination with Hardener EPH 161-P a post-curing (with the laminate backing) for approx. 15 hours at 60 °C is necessary.

It can be used as a top layer in conjunction with epoxy resin laminates and laminating ceramics. In contrast to resin and metal systems, the surfaces are polishable. The tooling gelcoat is hard-elastic, i.e. non-brittle, exhibits good edge strength, but is not resistant to styrene, which makes it unsuitable in conjunction with UP Pre-Gel.

Consumption: approx. 0.5–1 kg/m²

Hardener EPH 161-P
Mixing ratio: 100 : 17 parts by weight of resin to hardener
Processing time: 90 minutes (100 g batch size at 20 °C)
Gelling time: approx. 4 hours (1 mm application at 20 °C)
Curing: 24 hours at 23 °C, followed by post-curing (with the laminate backing) approx. 15 hours at at least 60 °C

A following post cure at elevated temperatures will improve the mechanical as well as the chemical properties and is highly recommended (> 60 °C for 15 h). A rate of heating of < 10 K/h is recommended, to prevent warpage and a print-through of the weave pattern.

Maximum heat distortion temperature after post curing (15 hours at 100 °C): approx. 120 °C

Applications:
Negative moulds for hand lay-up and vacuum moulding
Thermoforming moulds
RTM moulds


temporarily out of stock
temporarily out of stock

Reviews
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x Carbon rectangular rod 3.0 mm x 1.0 x 1000 mm
2 x Squared carbon wing joinner 5x5x220 mm
1 x Carbon fiber rod 1.5 mm x 1000 mm
1 x Carbon fiber rod 0.8 mmx1000 mm
1 x Carbon wing joinner 13,4 mm Ø 0,48 mm
1 x Carbon fiber rod 14 mmx1000 mm
1 x Carbon fiber rod 1.5 mm x 1000 mm
1 x Carbon fiber flat 1000x3.0x1.0 mm
1 x Carbon fiber flat 1000x3.0x0.13 mm
1 x Carbon fiber rod 4.0 mmx1000 mm
1 x Carbon fiber rod 7.0 mmx1000 mm
1 x Carbon fiber rod 1.5 mm x 2000 mm
1 x Carbon fiber rod 3.0 mm x 1000 mm
1 x Carbon fiber rod 10 mm x 1000 mm
1 x Carbon fiber rod 6.0 mmx1000 mm
1 x Carbon fiber rod 5.0 mmx1000 mm
1 x Wing-connector: Glass / Carbon tube (13.7/12.5) x 1000 mm
1 x Aluminum Bayonet / strongal D25 mm / 1 m
1 x SIMtransmitter 6 Mode 2
2 x Slave-cable USB Easy Sim
1 x RF9 Flight Simulator with Spektrum Controller
1 x Quicklock washer 1.5 mm (10 pcs)
1 x ABS "T" angle 8.0x8.0x1000 mm
1 x Carbon fiber rod 12 mm x 1000 mm
1 x 1 m servo "Premium" wire (white/red/blue)
1 x LightBox SR
1 x Eachine EV800D 5 Inches 800x480 FPV VR Goggles Monitor
1 x Carbon fiber rod 1.0 mm x 1000 mm
1 x 5.8G Receiver Helical Antenna with protecting case (SMA plug) 12
1 x Gates hinge 30x16 mm (2 pcs)
1 x Aluminun wheel collar 5 mm Ø (4 uds)
1 x Aluminun wheel collar 6 mm Ø (4 uds)
1 x 30 cm MULTIPLEX female connector
1 x PowerBox Smokepump JETs 2x outside
1 x Gates hinge
1 x Canopy hinges for Discus 2c, Discus 2a, Ventus 2cx (2pcs)
1 x Nylon hinge for flaps 33x9 (2 pcs)
1 x Large flex hinge (12 uds)
1 x Pin type hinge Al 4,5x70 mm to wire (2 pcs)
1 x Pin type hinge Al 4,5x70 mm demount (2 pcs)
1 x Aluminun wheel collar 2.5 mm Ø (4 uds)
1 x Katana Mini carbon wheel pants (2 pcs)
1 x EXTRA NG 74" yello/blue/red (Skywing RC)
1 x Propeller POWER-PROP 13x9 Izda
1 x Propeller electric carbon 10.5x7
1 x Extension MPX-MPX 20 cm
1 x PowerBox Smokepump
1 x Propeller POWER-PROP 11x6
1 x Cable servo PREMIUM MAXI 200m (blanco/rojo/azul) PVC
1 x Propeller electric carbon 10.5x6
1 x Extension for SensorSwitch 30cm
1 x Propeller electric carbon 10.5x8
1 x MPX-Dean "T" Adapter
1 x Conector JR Servo female (50 pcs)
1 x Propeller electric carbon 9.5x6
1 x Propeller electric carbon 10x7
1 x 5 line servos wire black (1 m)
1 x Propeller 11x4,7 SlowFlyer
1 x Propeller 8x4,3 SlowFlyer
1 x Oracover CHROME 2m
1 x Alignment dowels (2 parts, outer-Ø 8 mm) bag/ 100 pairs
1 x Epoxy SLOW-CURE™ 30 min (260g)
1 x Hardener Aero EPH 161 (250 g)
1 x Cable video GoPro
1 x Stickers-digit for marking
1 x Hardener P-25, canister 2.5Kg
1 x MEKP Harderner 100 g
1 x Epoxy SLOW-CURE™ 30 min (130g)
1 x resin-hardener L-385 H-385 (5000 g)
1 x Epoxy MID-CURE™ 15 min (130g)
1 x Mould Resin P 10 kg
3,260.03EUR
Manufacturers
Manufacturer Info
R-G.de
R-G.de Homepage
Other products
Languages
Español English
Currencies