Top » Catalog » Hardware » BEC/Cables/Conectors/Interruptor » SETOKW

16.00EUR

Opto Gas Engine Kill Switch
[SETOKW]

This kill switch is double Optically Coupled to isolate your ignition system from your radio system (No Interference!!). It also consist an additional safety functions.

Device features
• Includes a remote mountable ultra bright LED to indicate when the ignition is armed or not, or if the safety sequence protection is active.
• The LED diode informs also if Fail-Safe occured during flight (even after landing).
• Safety sequence protection for engine ignition powering up after model preparation.
• Double optically Coupled input/output is Isolated.
• Turning engine ignition ON or OFF directly from RC Transmitter
• No need to use additional mechanical switch for disconnecting ignition battery.
• 8 Bit microcontroller powered directly from RC receiver.
• 3,0 - 24,0 Volt Li-Po/Li-Ion/A123/Ni-Mh/NiCad Input (receiver side).
• 3,0 - 20,0 Volt Li-Po/Li-Ion/A123/Ni-Mh/NiCad MOSFET Output (ignition side).
• Possible to use one battery setup (independent two batteries setup by default).
• Max. current output: 5 Amp continous, 16 Amp peak
• Fail-Safe engine kill when interference or signal lose is longer then 1 second. (this function can be turned OFF).
• PPM-PCM 2048 – 1024 & 2.4Ghz Interface Support.
• Low Voltage Drop – Less than 150mv.
• 100% Surface Mount Technology.
• Heavy Gauge Wires 22AWG, universal connectors Futaba/JR.
• Small and light weight – only 15 Grams!

This device plugs into a spare receiver channel.

This is a must have safety device for any gas powered plane! This device allows you to safely kill your engine at anytime (on the ground, or inthe air!)

temporarily out of stock

Reviews

Customers who bought this product also purchased

Spark motor OS nº 3

temporarily out of stock

Categories

* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->

  3D IMPRESION
  ABS Rods-Strips
  ABS/GFK/CFK plate
  Actuator
  Adapters->
  Adhesives/Resin/Epoxy->
  Altimeters->
  Amperimeters
  Anemometer
  Auto-Pilot
  Bags/Covers
  Batteries->
  BEC/Cables/Conectors/Interruptor
  Bungee Launchers
  Cables
  Cameras->
  Carbon rod
  Carbon/Brass/Steel/ABS/Aluminium
  Catalogues
  Chargers->
  Clevis
  Combustible->
  Connectors
  Control horns
  Controlers->
  Coverings/Thermoretrac
  Decals
  Extension
  Extinguisher
  Ferritas
  Glasses
  Hardware
  Hinges
  Instruments / Panels
  Lights/Ilumination->
  Linkages
  Merchandising
  Motor
  Pilots
  Pinion extractor
  Power supply system/Data Recordi->
  Profiles
  Propelers->
  Screws
  Servos->
  Simulators
  Smoke/Rocketry/Fireworks
  Spinners->
  Spray/Painting/Dope/Solder Paste
  Steel/brass Rod/Aluminium
  Support/CG/Incidenc.
  Tapes/Closed/Bridles
  Tools
  Towing
  Transmitters/Receivers->
  Undercarriage->
  Wheels & Axles->
  Wing Joiner
  Wood
Car/Trucks->
Motors & Turbines->
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA

What's New?

21x14 BIELA propeller (3-blades) Pusher
89.00EUR

Information

Shipping & Returns
Privacy Notice
Conditions of Use
Financing
Point Program FAQ
Contact Us

We Accept

Quick Find

Shopping Cart

2 x	Big-Malibu XL Roof box with surfboard rack GREY
3 x	Small Crow DLE-170M
2 x	Silent-blocks DLE 170M
4 x	Motor DLE 430 cc - Paramotors
3 x	Motor DLE 200cc Premium Muffler
4 x	Motor DLE 200cc Std
2 x	Big Crow DLE-170M
1 x	Extension MPX-MPX 20 cm
1 x	Carbon tube (L 1000 mm, Ø18 mm, Ø16 mm)
1 x	Cable tie mounts 4.3 (4 uds)
1 x	Cabel PVC 2 x 0.25 mm2 (5 m) red-black
2 x	Balance "Y" Wire 6S, 2x JST-XH / 1x JST-EH
1 x	SE Ring 300 mm (2 pcs)
2 x	Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm)
1 x	30 cm MULTIPLEX female connector
1 x	Conector JR Servo male (10 pcs)
1 x	Anodized aluminium servo M4x5/8 screw (4 lilac pcs)
1 x	M2,5 5Diam short black ball link V2 (2 pcs)
2 x	Dean "T" - Futaba Adapter
1 x	Conector FUTABA Servo female BLUE silicon (10 pcs)
2 x	Strip ABS 2.0x8.0x1000 mm
1 x	Connector Sub-D 2+5 Male
1 x	Conector JR Servo female (10 pcs)
3 x	Connectors banana oro 6,0 mm Ultralight (M/F)
1 x	Socket head ball link M3 (2 uds)
2 x	Balanceradapter JST-XH (Heli 47G) 2-6 c.
2 x	Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH
1 x	Blind nut M5 (4 pcs)
1 x	Aluminium cap bolt washer M4 blue (8 pcs)
1 x	Painting GHT Lexan Black 150 ml
1 x	White smoke canister 100 g
2 x	Carbon fiber rod 20 mmx1000 mm
1 x	48 mm cylidric hinge Ø 2,5 mm (5 pcs)
1 x	Pin type hinge Al 4,5x70 mm (2 pcs)
1 x	WingFix ULTRA Black Edition
1 x	Cabel "Y" 30 cm (Futaba)
2 x	Carbon fiber rod 1.0 mm x 1000 mm
1 x	PARTALL® Hi-Temp Wax, 340 g
1 x	43 x 10 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x	Spannlack 1000 ml
1 x	Cable S.BUS 3 salidas 100 mm
2 x	Carbon fiber rod 10 mm x 1000 mm
2 x	Carbon fiber rod 1.5 mm x 1000 mm
1 x	Red smoke canister 100 g
1 x	Pin type hinge Al 4,5x70 mm demount (2 pcs)
1 x	SIMtransmitter 6 Mode 2
1 x	Interface Realflight Simulator
1 x	Sun Cover ULTIMATUM 2.0 (Hispano Aviacion)
1 x	Catalog AERO-NAUT 2016
1 x	Tirpiz Battleship 1:200
1 x
1 x	Remolcador "Jonny Hafenschlepper"
1 x	DUBRO - CUB WHEELS (1/3 SCALE) (558TLC) - 2PCS
1 x	Servo M2x7/16 screw (4 pcs)
1 x	70x23 Ø3.5 mm aluminium core wheel
1 x	Wheel FEMA 82 mm / 5 mm
1 x	Adapter lead MPX/EC3
1 x	Strip 2,0x2,0x330 mm
1 x	Interruptor SPS 70v 60/120A
1 x	20x1000 mm Ring Strap Back To Back
1 x	PSC 5
1 x	SE Ring 240 mm (2 pcs)
1 x	CC 03
3 x	XH male balance (4S) connector (2 pcs)
1 x	XH male balance (8S) connector (2 pcs)
3 x	XH female balance (3S) connector (2 pcs)
1 x	Wing conexion 2 servos JR/Graupner 50 cm
2 x	XH male balance (9S) connector (2 pcs)
2 x	100 Newtons FEMA absorber
3 x	XH male balance (3S) connector (2 pcs)
1 x	ALU servo arm 3 mm shaft
1 x	Carbon fiber rod 0.8 mmx1000 mm
1 x	PowerBox iGyro 3xtra
1 x	PowerBox PowerExpander SRS
1 x	PowerBox MAG Sensor
1 x	Super Light Wheels (Sponge Tyre) Ø 60mm x 19 mm (2pcs) axis Ø 3.
1 x	Wheel FEMA 152 mm / 8 mm
1 x	Battery charging cable XT60
1 x	Waterproof adhesive tape, width 19mm, length 25m
1 x	ABS Strip 1.0x5.0x1000 mm
1 x	Strip ABS 2.0x5.0x1000 mm
1 x	SPS 70V 140/280 A
1 x	SE Ring 350 mm (2 pcs)
1 x	Extension 5 lipos JST/C
1 x	Spikes Band (5 m)
2 x	Connectors banna oro 2 mm (M/F)
1 x	Cinta Goldfix 1m
1 x	Pad self adhesive, up to 3mm / 0.12″, (10 pcs)
1 x	3 copper lacquer wire Ø0,2 mm (1 m)
1 x	Round Rod 4,0x1000 mm
1 x	Connectors banna oro 3 mm (M/F)
1 x	26 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	Tape GFK 25 mm
1 x	XH female balance (7S) connector (2 pcs)
2 x	13 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	ABS Strip 1.5x6.0x1000 mm
1 x	SE Ring HACKER 300 mm (2 pcs)
1 x	Adapter lead MPX/XT60
1 x	ABS Strip 1.0x3.0x1000 mm
1 x	Male/Female prolonguer for Balancer Thunder Power 6S
1 x	Magnetic Interruptor MULTIPLEX
1 x	Bag connector 2 mm
1 x	4 LiPo XH>EH adapter
1 x	Electronic switch JETI SP6 0-15v/6A
1 x	10 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x	Male Prolonger TP 4/5S
1 x	Multi-adapter balancer JST - TP
1 x	Round Rod 1,25x1000 mm
1 x	Circlick securite
1 x	Pins M connect Multipin connectors AWG 20-24
2 x	Red 4 mm connector holder
1 x	SBEC Jeti
2 x	XH female balance (6S) connector (2 pcs)
1 x	APM2.6 Power module with 5.3V DC BEC
1 x	SE Ring 330 mm (4 pcs)
1 x	5 LiPo XH>EH adapter
1 x	"Y" charging 4mm wire (2 IN-1 OUT).
1 x	Strip ABS 2.0x10.0x1000 mm
1 x	MR30 connector male
1 x	Interruptor RX/Batterie
1 x	Foil for sticking flaps and ailerons
1 x	Connectors MPX male
1 x	20 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	Red copper lacquer wire Ø0,2 mm (5 m)
1 x	Pad Screw Mount M3, up to 3mm / 0.12″, (10 pcs)
1 x	Male prolonguer XH 30 cm 6 cell cable of silicone 0,25 mm
1 x	Red 3m5 mm connector holder
1 x	Bec MR UBEC 5A (5v/6v/7v)
2 x	Connectors banna oro 3,5 mm (M/F)
1 x	Multi-adapter balancer JST/C - TP
1 x	TP/TopFuel - XH 2/3S Adapter
1 x	SE Ring 450 mm (2 pcs)
1 x	Banna gold connector 2,5 mm (M/F)
2 x	Round Rod 6,0x1000 mm
1 x	PowerBox SparkSwitch RS
1 x	ABS Strip 1.0x4.0x1000 mm
1 x	SE Ring 360 mm (2 pcs)
1 x	Selfstart electronic switch
1 x	ABS I Strip 20x10x1000 mm
2 x	XH male balance (2S) connector (2 pcs)
1 x	SE Ring 480 mm (2 pcs)
1 x	Extension 5 lipos JST - JST/C
1 x	CC 02
1 x	JETImodel SINGLE BEC
1 x	Connectors MPX black male
1 x	ABS Strip 1.0x2.0x1000 mm
1 x	XH male balance (5S) connector (2 pcs)
1 x	TrainerCord (master-learner)
1 x	Round Rod 5,0x1000 mm
3 x	XH male balance (7S) connector (2 pcs)
1 x	Connector CAN 15
1 x	XT-60 connector (female)
1 x	Tape GFK 50 mm
1 x	MAX BEC 2D plus EX
1 x	Round Rod 2,5x1000 mm
1 x	Extension 5 lipos JST/C - JST
1 x	Opto Gas Engine Kill Switch
1 x	Strip ABS 2.0x3.0x1000 mm
1 x	ABS Strip 1.5x8.0x1000 mm
3 x	Soporte carbono MR30 (2 pcs)
1 x	ABS I Strip 10x5x1000 mm
1 x	20x200 mm battery rings
1 x	USB HLS prog. interface
1 x	Strip 2,5x1,25x330 mm
1 x	Strip 3,5x1,75x330 mm
1 x	PSC 6
1 x	Strip 1,5x1,5x330 mm
1 x	ABS Strip 1.5x4.0x1000 mm
1 x	Servo slow down unit (0,7-14,7 sec )
1 x	SE Ring 200 mm (2 pcs)
1 x	Extension 6 lipos XH > EH
1 x	Switc electronic 30 Amp
1 x	CellPRO 4S Adaptader (GP/KO up to 4S)
1 x	ABS Strip 1.5x3.0x1000 mm
1 x	SBEC 30 D
1 x	Cable-Tie 1.66x71mm / 0.07x2.8″ (20 pcs)
2 x	XT-60 connector (male)
1 x	XH female balance (9S) connector (2 pcs)
1 x	Marker ties (20 pcs)
2 x	UBEC 6A KAVAN
1 x	Connectors MPX male (PIN double)
1 x	SPS Remote switch actuator
1 x	Electronic switch JETI SP06 Opto
1 x	SE Ring 400 mm (2 pcs)
2 x	XT-90 connector (pair)
1 x	200 Newtons FEMA absorber
1 x	300 Newtons FEMA absorber
1 x	XH male balance (6S) connector (2 pcs)
1 x	Wing conexion 2 servos Futaba 50 cm
2 x	Wing connector 8pin with pin strip, plug & socket
1 x	XH female balance (5S) connector (2 pcs)
2 x	XH female balance (4S) connector (2 pcs)
1 x	Soldering PCBs 8pin, 5 pieces
1 x	400 Newtons FEMA absorber
2 x	XH LiPo extension lead
2 x	XT60 Connector with Holder Male 2pcs
1 x	Absorver mount set for 5-10 Kg models
1 x	150 Newtons FEMA absorber
1 x	LOGO 600 SX (kit)
2 x	Motor Scorpion HKIII 4035-560 Kv
1 x	Savox Highvoltage Brushless Servo SB-2272MG (Tail rotor)
1 x	VBar Control Touch, midnight black
1 x	VTX 477 Carbon Rotorblade
1 x	VBar NEO VLink 6.x Express, neon-yellow
2 x	Logo 400 SE VBar
1 x	Servo AN-8 HBA
1 x	ALU servo arm 90º 3 mm shaft
1 x	"L" servo arm 65x49 mm (2 pcs)
1 x	bavarianDEMON USB cable
1 x	Extension for SensorSwitch 30cm
1 x	PowerBox iGyro SRS + GPS Modul
1 x	Servo M2x5/16 screw (4 pcs)
1 x	Carbon fiber rod 1.5 mm x 1000 mm
1 x	Carbon fiber rod 5.0 mmx1000 mm
1 x	POWERBOX Magic Jeti Switch Royal SRS, Champion SRS
1 x	Carbon rectangular rod 10.0 mm x 1.0 x 1000 mm
1 x	PowerBox DigiSwitch V2 JR/JR
1 x	Carbon fiber rod 12 mm x 1000 mm
1 x	Carbon fiber rod 14 mmx1000 mm
1 x	PowerBox MagSensor black connector SRS/Champion
1 x	DUPLEX 2.4EX Central Box 220
1 x	DUPLEX 2.4EX Central Box 210
1 x	DUPLEX 2.4EX Central Box 220 + 2x Rsat2 + RC Switch
1 x	Motor Mega AC 16/15/05 CE F5J
1 x	KIRA 480-38 5,2:1
1 x	BALSA triangular 6x6x1000 mm
1 x	PYRO 700-45
1 x	Beech dowels 10 mm x 1000 mm
1 x	Radial mount for electric 2.5-5.6
2 x	BULLIT Wing 840 mm
1 x	Cessna SKYLANE T182 1.75m - Seagull Model
1 x	CARBON CUB FX-3 100-200CC ARF, 165" - 4200 mm (Hangar9)
1 x	Crystal RX 35.250 Ch 285
1 x	Micro Crystal RX 35.080 Ch 68
1 x	Motor OS 3820-1200 electric
1 x	Motor KAVAN PRO 2225-1600
1 x	BALSA trip 3.0x3.0x1000 mm
1 x	BALSA trip 2.0x10.0x1000 mm
1 x	Walnut wood slat 3.0x3.0x1000 mm
1 x	Actro 32-3 Heli MAX 5mm
1 x	Pine wood slat 3.0x7.0x1000 mm
1 x	PYRO 750-50L Competition
1 x	Glases Innovation Plus
1 x	Combo KAVAN PRO 3536-1000 + RAY 40 SB
1 x	PARAGON Trainer 46-55 1580 mm
1 x	BULLIT Wing 1095 mm
1 x	BOOMERANG II 40/46 ARF 1.55mm
1 x	PC-6 Pilatus Porter Big "Fredi" (PICHLER)
1 x	SCANNER 46-55 Sport Scale 1:7 ARF
1 x	DOMINO 46-55 Trainer 1583 mm
1 x	Motor ACTRO 28-4-880
2 x	Propeller FALCON 32,5x11 PUSHER Carbono
1 x	Connectors banna oro 4 mm (M/F) (ultralight)
1 x	2 mm male connector (2 pcs) with safety connector
1 x	MPX Sub-D Adaptor
1 x	MPX PCB "6 Pins", 5 pieces
1 x	MPX screwable clips (4 pcs)
1 x	Connectors banna oro 0,8 mm (M/F)
1 x	Servo NARO Max Std
1 x	DYMOND VTX UBS Programming adapter
1 x	Servo GO-1070MG 40 kg.cm 0.10s/60º
1 x	Aluminum Fold Prop Spinner 40 mm / 5mm
1 x	MPX-Dean "T" Adapter
1 x	FUTABA 20 mm servo arm with ball link
1 x	MPS Gas-Cap-Powerswitch
1 x	Futaba 52 mm servo arm
1 x	Male connector for 10 pines AWG
1 x	DPSI Ampere & Voltage bundle
1 x	Female connector for 6 pines AWG
1 x	Sandwich carbon + poplar 4mm + carbon 480x290 mm
1 x	DPSI Micro SingleBat 5.9V/7.2V magnetic switch
1 x	Motor DLE 170 M- Paramotors
1 x	Conector AS150 7mm antichispazo (Set: 2 pares)
1 x	Servo Connector Brackets (10 pcs)
1 x	Connectors banna oro 4 mm (M/F)
1 x	XPower H PROP HUB Ø6.0/42.5mm 0º
1 x	Aluminum Fold Prop Spinner 30 mm / 3.17 mm
1 x	White Fold Prop Spinner 38 mm / 5 mm shaft / 8 mm propellers
1 x	USB interface ALTIS
1 x	Aluminium wide washer M4 Black (4 pcs)
1 x	Female connector for 16 pines AWG
1 x	CM-3
1 x	5 mm gas motor standoff
1 x	Wing connector 8pin with pin strip, plug & socket
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x6.0 mm (5 pcs)
1 x	Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 50 m
1 x	Release wax 250ml
1 x	AX-60 starters (5 pcs)
1 x	Connectors banna oro 6,0 mm (M/F)
1 x	Protector Connector MPX (1 pair)
1 x	Kontronik connector (10 connectors, 5 pairs)
1 x	Connectors DEANS 4 pins (1 pair)
1 x	Connectors banna oro 2 mm (M/F) (ultralight)
1 x	Gold antispark 4 mm plug
1 x	Banna gold connector 2,5 mm (100 M/F pairs)
1 x	Gold antispark 5,5 mm plug

61,103.68EUR