Top » Catalog » Hardware » BEC/Cables/Conectors/Interruptor » SETOKW

16.00EUR

Opto Gas Engine Kill Switch
[SETOKW]

This kill switch is double Optically Coupled to isolate your ignition system from your radio system (No Interference!!). It also consist an additional safety functions.

Device features
• Includes a remote mountable ultra bright LED to indicate when the ignition is armed or not, or if the safety sequence protection is active.
• The LED diode informs also if Fail-Safe occured during flight (even after landing).
• Safety sequence protection for engine ignition powering up after model preparation.
• Double optically Coupled input/output is Isolated.
• Turning engine ignition ON or OFF directly from RC Transmitter
• No need to use additional mechanical switch for disconnecting ignition battery.
• 8 Bit microcontroller powered directly from RC receiver.
• 3,0 - 24,0 Volt Li-Po/Li-Ion/A123/Ni-Mh/NiCad Input (receiver side).
• 3,0 - 20,0 Volt Li-Po/Li-Ion/A123/Ni-Mh/NiCad MOSFET Output (ignition side).
• Possible to use one battery setup (independent two batteries setup by default).
• Max. current output: 5 Amp continous, 16 Amp peak
• Fail-Safe engine kill when interference or signal lose is longer then 1 second. (this function can be turned OFF).
• PPM-PCM 2048 – 1024 & 2.4Ghz Interface Support.
• Low Voltage Drop – Less than 150mv.
• 100% Surface Mount Technology.
• Heavy Gauge Wires 22AWG, universal connectors Futaba/JR.
• Small and light weight – only 15 Grams!

This device plugs into a spare receiver channel.

This is a must have safety device for any gas powered plane! This device allows you to safely kill your engine at anytime (on the ground, or inthe air!)

temporarily out of stock

Reviews

Customers who bought this product also purchased

Spark motor OS nº 3

temporarily out of stock

Categories

* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->

  3D IMPRESION
  ABS Rods-Strips
  ABS/GFK/CFK plate
  Actuator
  Adapters->
  Adhesives/Resin/Epoxy->
  Altimeters->
  Amperimeters
  Anemometer
  Auto-Pilot
  Bags/Covers
  Batteries->
  BEC/Cables/Conectors/Interruptor
  Bungee Launchers
  Cables
  Cameras->
  Carbon rod
  Carbon/Brass/Steel/ABS/Aluminium
  Catalogues
  Chargers->
  Clevis
  Combustible->
  Connectors
  Control horns
  Controlers->
  Coverings/Thermoretrac
  Decals
  Extension
  Extinguisher
  Ferritas
  Glasses
  Hardware
  Hinges
  Instruments / Panels
  Lights/Ilumination->
  Linkages
  Merchandising
  Motor
  Pilots
  Pinion extractor
  Power supply system/Data Recordi->
  Profiles
  Propelers->
  Screws
  Servos->
  Simulators
  Smoke/Rocketry/Fireworks
  Spinners->
  Spray/Painting/Dope/Solder Paste
  Steel/brass Rod/Aluminium
  Support/CG/Incidenc.
  Tapes/Closed/Bridles
  Tools
  Towing
  Transmitters/Receivers->
  Undercarriage->
  Wheels & Axles->
  Wing Joiner
  Wood
Car/Trucks->
Motors & Turbines->
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA

What's New?

DUPLEX backpack for Jeti DS handheld transmitter
58.00EUR

Information

Shipping & Returns
Privacy Notice
Conditions of Use
Financing
Point Program FAQ
Contact Us

We Accept

Quick Find

Shopping Cart

1 x	Premium servo extension 50cm
2 x	Extension silicon 100 cm (Graupner)
2 x	Cable silicona female batt. receptor 30 cm (Futaba)
1 x	Extension 90 cm (Futaba)
2 x	Cable silicona macho batt. receptor 30 cm (Futaba)
1 x	Cabel "Y" 30 cm (Futaba)
2 x	Extension silicon 10 cm (Graupner)
2 x	Extension 7.5 cm
1 x	Futaba Female 40 cm extension
1 x	Prolongador S-Bus JR/JR 10cm
1 x	0,14 mm PVC servo wire extension, ZH micro conector.
1 x	Cabel "Y" 15 cm
1 x	Futaba male 40 cm extension
1 x	Extension silicon 30 cm male (Futaba)
1 x	Extension PVC 150 cm (Graupner)
1 x	Futaba Female 40 cm extension
1 x	Premium servo extension 25cm
2 x	Extension silicon 35 cm male (Futaba)
2 x	Extension 100 cm (Futaba)
1 x	Cable S.BUS 3 salidas 300 mm
2 x	Extension silicon 100 cm (Futaba)
2 x	silicon 100 cm Futaba Extension Ø 0,35 mm
3 x	Extension 15 cm (Futaba)
1 x	Motor DLE 200cc Std
2 x	DUPLEX USBa USB-Adapter for Jeti Duplex Items
1 x	JETImodel SINGLE BEC
2 x	TrainerCord (master-learner)
1 x	CM-3
1 x	Dean "T" - Futaba Adapter
1 x	USB HLS prog. interface
1 x	Balance "Y" Wire 7S, 2x JST-XH / 1x JST-EH
2 x	"Y" charging 4mm wire (2 IN-1 OUT).
3 x	3 LiPo XH>EH adapter
3 x	Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH
2 x	Cabel charger transmitter GRAUPNER
3 x	CC 03
2 x	4 LiPo XH>EH adapter
2 x	Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm)
1 x	Cabel charger battery transmiter Futaba 2x0,5 qmm (50 cm)
2 x	MPX-Dean "T" Adapter
3 x	CC 01
1 x	30 cm BEC cable (male)
1 x	Adapter lead MPX/EC3
2 x	TP/TopFuel - XH 2/3S Adapter
1 x	CellPRO 4S Adaptader (GP/KO up to 4S)
1 x	Pin type hinge Al 4,5x70 mm to wire (2 pcs)
1 x	Pin type hinge Al 4,5x70 mm demount (2 pcs)
1 x	White smoke bombs AX-18 (5 pcs)
3 x	Small pinned hinge (12 uds)
1 x	Nylon hinge for flaps 33x9 (2 pcs)
2 x	Nylon hinge 20x15x0,3 (10 pcs)
1 x	Mixers smoke bombs AX-60 (5 pcs)
1 x	Nylon hinge 20x20x0,3 (10 pcs)
1 x	AX-60 starters (5 pcs)
1 x	Yellow smoke canister 140 g
1 x	White smoke bombs AX-3 (10 pcs)
1 x	PCARD Wireless System
1 x	White smoke canister 100 g
1 x	Fast'n EZ-CA-Hinge (12 uds)
1 x	Propeller balancer
1 x	Pin type hinge Al 3,0x50 mm (2 pcs)
1 x	15 mm reinforced hinge
1 x	Unmounted aluminium pin 6x98 mm (2 pcs)
1 x	Pin type hinge Al 3,0x50 mm demount (2 pcs)
1 x	Nylon hinge for flaps/gates 27x10,5 (2 pcs)
2 x	Yellow smoke canister 65 g
1 x	White smoke canister 65 g
2 x	Nylon hinge 15x0,3 (10 pcs)
2 x	33 x 8 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x	Surface Indicator Gauge Small
1 x	Blue smoke canister 140 g
2 x	Angle measurer
1 x	"S" set for boats
1 x	Miniature brass strap hinge, 1 m
3 x	White smoke bombs AX-60 (5 pcs)
1 x	Pin type hinge Al 4,5x70 mm (2 pcs)
1 x	Canopy hinges for Discus 2c, Discus 2a, Ventus 2cx (2pcs)
1 x	Ventral support for AX-18/AX-60
1 x	Electric rocket starters (6 pcs)
1 x	Gates hinge
1 x	48 x 10 mm cylidric hinge Ø 3,0 mm (10 pcs)
1 x	"M" set
1 x	Yellow smoke canister 100 g
1 x	Cylidric hinge 43 mm Ø 2,5 mm (5 pcs)
3 x	Parachute expulsion foam
1 x	Flap hinge 33x9 mm (6 pcs)
2 x	Blue smoke canister 100 g
1 x	Large flex hinge (12 uds)
2 x	Long pinned hinge (12 uds)
2 x	Red smoke canister 140 g
1 x	Green smoke canister 140 g
1 x	67 mm cylidric hinge Ø 5 mm (4 pcs)
1 x	Gates hinge black 30x16 mm (2 pcs)
1 x	B4-0 rocket charges (6 pcs)
1 x	Smoke set "M"
1 x	Smoke set "S"
1 x	2 mm female connector (2 pcs) with safety connector
1 x	Carbon fiber flat 1000x3.0x0.5 mm
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x1.2 mm (10 pcs)
3 x	Suncover 100cc Red
1 x	Extension silicon 35 cm (Futaba)
2 x	Support conector MPX (6 pcs)
2 x	Support XT60 conector (2 pcs)
2 x	Support Pitot JETI
1 x	Rotorshape Autogyro
1 x	Red copper lacquer wire Ø0,2 mm (5 m)
1 x	Balanceradapter JST-XH (Heli 47G) 2-6 c.
1 x	Bec MR UBEC 5A (5v/6v/7v)
1 x	Extension silicon 30 cm male (Graupner)
1 x	Cabel "Y" 30 cm (graupner)
1 x	Extension lead 15 cm Multiplex
1 x	servo adapter lead, JST-SH socket - JR male Pin, for GR-12SH+HoT
1 x	SPS Remote switch actuator
1 x	Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm)
2 x	PWC6 PowerWingConnector for 6 servos with fuselage socket
1 x	Male connector for 20 pines AWG
2 x	USB Interface REVOLECTRIX for CellPRO 10s
1 x	2 LiPo XH>EH adapter
1 x	Double conector with JR adapter and 200 mm extension
1 x	Balance "Y" Wire 6S, 2x JST-XH / 1x JST-EH
1 x	Propeller FALCON 32,5x11 PUSHER Carbono
2 x	CC 05
2 x	SPARK Switch 12v
1 x	USB interface ALTIS
1 x	Hovercraft sailcloth
1 x	Pilot WWII US Navy Pacific 12" Scale 1/6-1/5
1 x	Piloto Jet "Red" 1/6 Scale
1 x	Piloto JET 1:3,5
1 x	1/6 Pilot "Tony"
1 x	1/4 Pilot "Heidi"
1 x	Piloto RC Civil 1/5- 1/6 Scale 12"
1 x	Pilatus PC-21 50E RED/WHITE (SebArt)
1 x	2000A 12V Lithium Jump Starter with 150PSI Air inflator
2 x	3 copper lacquer wire Ø0,2 mm (1 m)
2 x	Connector Sub-D 2+5 Female
2 x	Circlick securite
1 x	Micro Switch button
1 x	Multi-adapter balancer JST/C - TP
1 x	Male connector JST SH 1.0mm with 10 cm wire
1 x	Female connector for 6 pines AWG
1 x	Female connector for 10 pines AWG
1 x	Black copper lacquer wire Ø0,2 mm (5 m)
1 x	SBEC 40
1 x	Male/Female prolonguer for Balancer Thunder Power 6S
1 x	EWC6 40 cm wing connector
1 x	Switc electronic 30 Amp
1 x	PSC 5
1 x	Connector CAN 15
2 x	MAX BEC 2
1 x	PSC 6
1 x	Copper lacquer wire Ø0,2 mm (5 m)
1 x	Three-position switched channel, short
1 x	Medium pin type hinge (12 uds)
3 x	Pin hinge 34x16 mm (10 uds)
1 x	67 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs)
1 x	48 mm cylidric hinge Ø 2,5 mm (5 pcs)
1 x	Transmitter Balancer Futaba V
1 x	Cylidric hinge 33 mm Ø 2 mm (5 pcs)
1 x	Gates hinge 30x16 mm (2 pcs)
1 x	43 x 10 mm cylidric hinge Ø 2,5 mm (10 pcs)
2 x	ROBART POINT HINGE 4,7mm (5 pcs)
1 x	Remote electric ignition system
1 x	Pin type hinge Al 6x98 mm (2 pcs)
1 x	Green smoke canister 100 g
1 x	"S" set for planes
1 x	10-15mm Servo Arm HITEC
1 x	Extension silicon 25 cm (Graupner)
1 x	Sun Cover ULTIMATUM 2.0 (Hispano Aviacion)
1 x	50 mm servo arm with bearing (2 pcs)
1 x	40 mm servo arm with bearing (2 pcs)
1 x	ANGEL 48" pp red/blue/white
1 x	20-25mm Servo Arm
1 x	Brazo servo aluminio 1.25/1.5" Futaba/MKS/Savox
1 x	Sun Cover PC 21 XXL (JMB Jets)
1 x	Z-shaped servo mount
1 x	Servo arm with 6 mm hole to FEMA 9800A
1 x	L-shaped servo mount
1 x	Servo holder for retract
1 x	Extension silicon 10 cm (Futaba)
1 x	Extension silicon 75 cm (Futaba)
1 x	LA500 pre-rotation gear
1 x	LA500 pre-rotation gear hub
1 x	Battery plate
1 x	LA500 ciclic lever
1 x	Pilot LA 500
1 x	LA500 housing-lower cyclic
1 x	Balls 4 mm
1 x	LA500 cyclic central part
1 x	Head core
1 x	Support Flush MPX Conector (6 pcs)
1 x	Recessed MPX connector support (6 pcs)
1 x	Soporte grifo FESTO (2 pcs)
1 x	TMM 1210-3S heli
1 x	SBEC 30 D
1 x	EWC3 100 cm wing connector
1 x	PowerBox SparkSwitch RS
1 x	LiIon Battery 3000 mAh 3.3v 15A (2 pcs)
1 x	Indoor hinge with servo arm integraded
1 x	Sandwich carbon + poplar 3mm + carbon 480x290 mm
1 x	Male Prolonger TP 4/5S
1 x	CC 02

9,287.31EUR