Top » Catalog » Hardware » BEC/Cables/Conectors/Interruptor » EMCA15020

119.90EUR

DPSI Ampere battery backer
[EMCA15020]

Powerful battery backer with peak current capacity of up to 60 ampere. The DPSI Ampere can be used as dual power supply for receivers, turbines or similar electric consumers of R/C models. System stability of the DPSI Ampere is ensured by connecting two batteries. If one battery fails, safe operation is guaranteed by the second battery. Normally, both batteries are discharged symmetrically and simultaneously (at the same time). Due to the parallel connected batteries the current is split in half for each battery. The DPSI Ampere is switched ON/OFF electronically by placing a magnet on the corresponding position on the device housing.

The DPSI Ampere can handle a permanent current of 50 ampere. So it is the perfect solution for all high current applications. Thanks to an integrated charging connector both connected batteries can be charged simultanously with only one charging device.

The DPSI Ampere is the first EMCOTEC battery backer that can be operated with 3S LiPo batteries or batteries with voltages up to 13.2 volts. So the module is much more than a conventional dual power supply for receivers. Due to the higher voltage also devices such as turbines can be reliably powered with the DPSI Ampere.

Delivery includes switching magnet with EMCOTEC patch, backup magnet, 3D sticker as well as German and English operating instructions.

Specifications
Current sources: 4S to 8S NiCd / NiMH batteries, 2S to 3S Lithium++ batteries (LiPo, LiFePO4, LiIon)
Operating voltage range: 2.6V (*) .... 13.2V
Nominal input voltage: 3.6V .... 13.0V
Output voltage: same as input voltage (no dropout losses)
Quiescent current (turned off): < 4µA per battery
Quiescent current (turned on): approx. 30mA total
Max. continuous current: 50A (30A per channel)
Max. peak current (10 sec.): 60A (30A per channel)
Internal resistance: approx. 3mR
CE test: according to 2004/108/EG
Environmental conditions: -10°C .... +50°C (14°F ... 122°F)
Permissible temperature range: -25°C .... +70°C (-13°F ... 158°F)
Dimensions (L x W x H): 60mm x 64mm x 16mm (2.36in x 2.52in x 0.63in)
Weight: 45g (1.59oz)

temporarily out of stock

Reviews

Categories

* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->

  3D IMPRESION
  ABS Rods-Strips
  ABS/GFK/CFK plate
  Actuator
  Adapters->
  Adhesives/Resin/Epoxy->
  Altimeters->
  Amperimeters
  Anemometer
  Auto-Pilot
  Bags/Covers
  Batteries->
  BEC/Cables/Conectors/Interruptor
  Bungee Launchers
  Cables
  Cameras->
  Carbon rod
  Carbon/Brass/Steel/ABS/Aluminium
  Catalogues
  Chargers->
  Clevis
  Combustible->
  Connectors
  Control horns
  Controlers->
  Coverings/Thermoretrac
  Decals
  Extension
  Extinguisher
  Ferritas
  Glasses
  Hardware
  Hinges
  Instruments / Panels
  Lights/Ilumination->
  Linkages
  Merchandising
  Motor
  Pilots
  Pinion extractor
  Power supply system/Data Recordi->
  Profiles
  Propelers->
  Screws
  Servos->
  Simulators
  Smoke/Rocketry/Fireworks
  Spinners->
  Spray/Painting/Dope/Solder Paste
  Steel/brass Rod/Aluminium
  Support/CG/Incidenc.
  Tapes/Closed/Bridles
  Tools
  Towing
  Transmitters/Receivers->
  Undercarriage->
  Wheels & Axles->
  Wing Joiner
  Wood
Car/Trucks->
Motors & Turbines->
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA

What's New?

Emisora Spektrum NX10 10ch (solo Tx)
619.92EUR

Information

Shipping & Returns
Privacy Notice
Conditions of Use
Financing
Point Program FAQ
Contact Us

We Accept

Quick Find

Shopping Cart

1 x	M2,5 Diam metal ball link V3 (2 pcs)
1 x	M2,5 5Diam metal ball link V3 (2 pcs)
1 x	Joint with bearing M2,5 22x5,5
1 x	6 mm hexagonal ball link M3 (10 pcs)
1 x	M2/M1/6 3Diam long black ball link V1 (2 pcs)
1 x	Ball link M2 (10 pcs)
1 x	M3 Maxi ball link (2 uds)
1 x	Ball link M3 RPA's-UAV's
1 x	6 mm ball link M3 (10 pcs)
1 x	Joint with bearing M2 22x5,5
1 x	M2/M1/6 3Diam short black ball link V1 (6 pcs)
1 x	M2,5 5Diam short black ball link V2 (2 pcs)
1 x	M2 5Diam short black ball link V2 (2 pcs)
1 x	Ball link M3 (10 pcs)
2 x	Blue metalic ball link M2/2 azul (2 pcs)
1 x	M2,5 5Diam black ball link V2 (2 pcs)
1 x	Blue metalic ball link M3/3 azul (2 pcs)
1 x	M3 Maxi ball link (2 uds)
1 x	M3/5 Diam metal short ball link V3 (2 pcs)
1 x	Long ball link M2 (6 uds)
1 x	M3 Maxi ball link (2 uds)
1 x	Motor DLE 430 cc - Paramotors
2 x	Silent-blocks DLE 170M
1 x	Small Crow DLE-170M
2 x	Motor DLE 170 M- Paramotors
1 x	Propeller FALCON 32,5x11 PUSHER Carbono
1 x	Motor DLE 200cc Premium Muffler
1 x	Parachute PV6 for F3J
1 x	Rescue 1,8m2 / BackPack
2 x	Opale Rucksack
1 x	Windsock Ozone L -1200 mm
1 x	Parachute BACKUP X100
1 x	Windsock Ozone L - 700 mm
2 x	Paramotor BackPack XXS (without accessories)
1 x	Paramotor BackPack XXS 2
1 x	Set cintas unión paracaídas 145 cm
1 x	Aramid 50 daN 50 m
1 x	Para-RC Mix
1 x	Canopy Lock V1 M3 Blue (2 pcs)
1 x	Electric spoiler 250 mm (2 pcs)
1 x	Cabin latch Fox MDM1 4m (pair)
1 x	Crimping sleeves for cable 0.85 mm (10 pcs)
1 x	Steering arm 16 mm Ø 3 mm
2 x	Cockpit plastic closing
1 x	Cap closure 33/23.5mm (2 uds)
1 x	Canopy Latch
1 x	Steering arm 16 mm Ø 3 mm (2 uds)
1 x	Stainless steel cable Ø 0.5 mm (10 m)
1 x	Cierre cabina aluminio Ø4, I=10 mm
1 x	Locking cable tie 3.2x142 (uds)
2 x	Steering arm 16 mm Ø 4 mm
1 x	Screw-lock connector M2 (2 uds)
1 x	Crimping sleeves for cable 1.3 mm (10 pcs)
1 x	Steering arm 12 mm Ø 4 mm (2 uds)
1 x	Aluminium alloy coupler for carbon tube 6/M4
1 x	Locking cable tie 2.5x100 (uds)
1 x
1 x	Red copper lacquer wire Ø0,2 mm (5 m)
1 x	33 x 8 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x	15 mm reinforced hinge
1 x	Straightened rod Ø 4.5 mm x 1000 mm
1 x	TeXtreme® Carbon tape 38 g/m² (IM, unidirectional) 20 mm x 100m
1 x	M2 5Diam black ball link V2 (2 pcs)
1 x	Motor DLE 200cc Std
1 x	Adapter 3,2 mm M5 for spinner 30 mm fixed propeller
1 x	Allen wheel collar M3x3
1 x	Adapter 3,0 mm M5 for spinner 30 mm fixed propeller
1 x	Glow starter with charger 230v
1 x	Servo SAVOX SV-1260 MG
1 x	Servo mounting frame SV-1260MG
1 x	Savox Brushless Servo SC-1267 SG
1 x	Allen wheel collar M4x6
1 x	Futaba 17 mm servo arm with ball link HITEC
1 x	Fully Threaded Steel Rod Duralumin 110 mm M3 (2 pcs)
1 x	45 mm rods + T patellas set for direction control
1 x	Blue aluminium servo arm V1-Hitec 1,5" inch M3
1 x	SUPER STRANGTH SERVO ARMS FUTABA LONG (8 PCS)
1 x	Glow Plug Clip 1.3 Ah
2 x	Big Crow DLE-170M
1 x	4 LiPo XH>EH adapter
1 x	Dean "T" - Futaba Adapter
1 x	Balance "Y" Wire 6S, 2x JST-XH / 1x JST-EH
1 x	Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm)
1 x	"Y" charging 4mm wire (2 IN-1 OUT).
1 x	CC 03
1 x	Cabel charger battery transmiter Futaba 2x0,5 qmm (50 cm)
1 x	Battery charging cable XT60
1 x	Circlick securite
1 x	Adapter lead MPX/EC3
1 x	Balanceradapter JST-XH (Heli 47G) 2-6 c.
1 x	5 LiPo XH>EH adapter
1 x	3 copper lacquer wire Ø0,2 mm (1 m)
1 x	TP/TopFuel - XH 2/3S Adapter
1 x	MPX-Dean "T" Adapter
1 x	Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm)
1 x	TrainerCord (master-learner)
1 x	TP/TopFuel - JST-EH 4/5S Adapter
1 x	Bec MR UBEC 5A (5v/6v/7v)
1 x	Paramotor Trike XL
1 x	Wing OXY 0,5 pulgadas2
1 x	Wing OXY 5,0 m2
1 x	Rudder 2_Tray 4.5~5 inch
1 x	Servo MKS HV6120H
1 x	Servo inverter
1 x	Cable grommet Ø 4 mm (4 uds)
1 x	Servo MKS HV6130
1 x	Cable grommet 9.5 mm (4 uds)
1 x	Servo MKS HV747
1 x	90x60 mm standart servo cover
2 x	Fully Threaded Steel Rod alumin 100 mm M3 (2 pcs)
1 x	28x5 mm wires output (2 pcs)
1 x	Tip wing protector 28x10x12 (2 pcs)
1 x	100 mm rods + T patellas set for direction control
1 x	Aluminun wheel collar 3 mm Ø (4 uds)
1 x	SAVOX SH 0254 servo
1 x	Red aluminium servo arm V3-Futaba 3,5inch
1 x	Fully Threaded Steel Rod alumin 90 mm M3 (2 pcs) knurled
1 x	46 mm Futaba servo arm tandem with ball link
1 x	XTorque CFK Servohebel 38 HITEC 25T
1 x	Savox HV Brushless Servo SB-2270SG (Swashplate)
1 x	Fully Threaded Steel Rod M3
1 x	Crimping sleeves for cable 0.70 mm (10 pcs)
1 x	120x60 mm SLH KOVO wheel
1 x	Excentric gearbox for 2,3mm axis (2,33:1)
1 x	Circlik for shaft 2.3 mm (10 pcs)
1 x	Excentric gearbox for 3,2mm axis (2,33:1)
1 x	Excentric gearbox for 2,0mm axis (5,0:1)
1 x	Excentric gearbox for 2,3mm axis (3,5:1)
1 x	Excentric gearbox for 3,2mm axis (3,5:1)
1 x	Excentric gearbox for 2,3mm axis (3,0:1)
1 x	Foam wheel Ø 38 mm (2 pcs)
1 x	Cooler motor type 150
1 x	76 mm light wheels (2 pcs)
1 x	SLICK 360-A 104" (2640 mm)
1 x	EXTRA NG 74" white/red/blue (Skywing RC)
1 x	Servo M2x9/16 screw (4 pcs)
1 x	USB Mini Camera endoscope
1 x	Camera Sony 4140+673 CCD with Built-in 200mw TX + antenna
1 x	Flat washer 4.3 mm (20 pcs)
1 x	Frontal support Speed 280
1 x	Excentric gearbox for 2,0mm axis (4,1:1)
1 x	Circlik for shaft 3.2 mm (10 pcs)
1 x	Excentric gearbox BB for motor 600, 3,2mm axis (1,75:1)
1 x	Flat washer 1.7 mm (20 pcs)
1 x	Frontal support Speed 600
1 x	Frontal support Speed 400/480
1 x	Cockpit latch closing I=10 mm
1 x	800TVL CMOS camera for FPV
1 x	Clevis plastico I=26 mm / hole 2mm / pin 1 (2 pcs)
1 x	Excentric gearbox BB for motor 600, 3,2mm axis (2,8:1)
1 x	COMPACT drive 26/45-20 DL=175 motor
1 x	Control horn long w/ball
1 x	Flat washer 3.2 mm (20 pcs)
1 x	Clevis plastico I=45 mm / hole 3mm / pin 1 (2 pcs)
1 x	Excentric gearbox for 2,0mm axis (3,75:1)
1 x	Clevis plastico I=30 mm / hole 2.5mm / pin 1 (2 pcs)
1 x	Excentric gearbox for 2,0mm axis (5,0:1)
2 x	Flat washer 2.2 mm (20 pcs)
1 x	Excentric gearbox BB for motor 600, 3,2mm axis (2,33:1)
1 x	Couple M4 for wire (10 pcs)
1 x	Propeller 10x4,7 SlowFlyer
2 x	Cooler motor type 300
1 x	Propeller 11x4,7 SlowFlyer
1 x	Cooler motor type 400
1 x	PITTS CHALLENGER 87″ 2.20m (120cc) 02 ARF
1 x	EXTRA 330L 35% hardware pack (Precision Aerobatics)
1 x	EDGE 540-A 105" (2660 mm)
1 x	Horn mando small (2 pcs)
1 x	Split M1,2x10 (10 pcs)
1 x	Lock washer 2.7 mm (20 pcs)
1 x	Bearings for motor HACKER C50
1 x	DOMINO 46-55 Trainer 1583 mm
1 x	SHOCK CUB 102" 2.600 mm 38-50cc YELLOW (Seagull Models)
1 x	SSPS105 Super Hi-Power servo
1 x	PITTS CHALLENGER 87″ 2.20m (120cc) 03 ARF
1 x	Ø 38 mm fiberglass motor-holder for electric motors
1 x	Disipador para motor Hacker B 20 (or motors up to Ø20 mm)
1 x	Size "M" motor holder for class 400
1 x	Size "M" motor holder for class 400
1 x	10 mm gas motor standoff
1 x	Motor mount for 1200 mm models
1 x	Motor holder for AC 28/7
1 x	Fiberglass motor-holder for electric motors
1 x	Motor mount for 1 m models
1 x	Central support Speed 280
1 x	BULLIT Wing 1095 mm
1 x	PILATUS PC-6 Turbo Porter 33% 5.290 mm
1 x	Bidule 55 2460 mm Cabina
1 x	BOOMERANG II 40/46 ARF 1.55mm
1 x	Motor OS 3820-1200 electric
1 x	SkyMaxx 1.550 mm (kit)
1 x	BULL MØ1 2.600mm "RED BULL"
1 x	Cap Hispano Aviación
1 x	BULL MØ1 2.600mm "ALPINE"
1 x	Bags de Luxe ULTIMATUM 2.0

40,512.01EUR