Top » Catalog » Hardware » BEC/Cables/Conectors/Interruptor » EMCA15020

119.90EUR

DPSI Ampere battery backer
[EMCA15020]

Powerful battery backer with peak current capacity of up to 60 ampere. The DPSI Ampere can be used as dual power supply for receivers, turbines or similar electric consumers of R/C models. System stability of the DPSI Ampere is ensured by connecting two batteries. If one battery fails, safe operation is guaranteed by the second battery. Normally, both batteries are discharged symmetrically and simultaneously (at the same time). Due to the parallel connected batteries the current is split in half for each battery. The DPSI Ampere is switched ON/OFF electronically by placing a magnet on the corresponding position on the device housing.

The DPSI Ampere can handle a permanent current of 50 ampere. So it is the perfect solution for all high current applications. Thanks to an integrated charging connector both connected batteries can be charged simultanously with only one charging device.

The DPSI Ampere is the first EMCOTEC battery backer that can be operated with 3S LiPo batteries or batteries with voltages up to 13.2 volts. So the module is much more than a conventional dual power supply for receivers. Due to the higher voltage also devices such as turbines can be reliably powered with the DPSI Ampere.

Delivery includes switching magnet with EMCOTEC patch, backup magnet, 3D sticker as well as German and English operating instructions.

Specifications
Current sources: 4S to 8S NiCd / NiMH batteries, 2S to 3S Lithium++ batteries (LiPo, LiFePO4, LiIon)
Operating voltage range: 2.6V (*) .... 13.2V
Nominal input voltage: 3.6V .... 13.0V
Output voltage: same as input voltage (no dropout losses)
Quiescent current (turned off): < 4µA per battery
Quiescent current (turned on): approx. 30mA total
Max. continuous current: 50A (30A per channel)
Max. peak current (10 sec.): 60A (30A per channel)
Internal resistance: approx. 3mR
CE test: according to 2004/108/EG
Environmental conditions: -10°C .... +50°C (14°F ... 122°F)
Permissible temperature range: -25°C .... +70°C (-13°F ... 158°F)
Dimensions (L x W x H): 60mm x 64mm x 16mm (2.36in x 2.52in x 0.63in)
Weight: 45g (1.59oz)

temporarily out of stock

Reviews

Categories

* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->

  3D IMPRESION
  ABS Rods-Strips
  ABS/GFK/CFK plate
  Actuator
  Adapters->
  Adhesives/Resin/Epoxy->
  Altimeters->
  Amperimeters
  Anemometer
  Auto-Pilot
  Bags/Covers
  Batteries->
  BEC/Cables/Conectors/Interruptor
  Bungee Launchers
  Cables
  Cameras->
  Carbon rod
  Carbon/Brass/Steel/ABS/Aluminium
  Catalogues
  Chargers->
  Clevis
  Combustible->
  Connectors
  Control horns
  Controlers->
  Coverings/Thermoretrac
  Decals
  Extension
  Extinguisher
  Ferritas
  Glasses
  Hardware
  Hinges
  Instruments / Panels
  Lights/Ilumination->
  Linkages
  Merchandising
  Motor
  Pilots
  Pinion extractor
  Power supply system/Data Recordi->
  Profiles
  Propelers->
  Screws
  Servos->
  Simulators
  Smoke/Rocketry/Fireworks
  Spinners->
  Spray/Painting/Dope/Solder Paste
  Steel/brass Rod/Aluminium
  Support/CG/Incidenc.
  Tapes/Closed/Bridles
  Tools
  Towing
  Transmitters/Receivers->
  Undercarriage->
  Wheels & Axles->
  Wing Joiner
  Wood
Car/Trucks->
Motors & Turbines->
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA

What's New?

SAITO FG-120 TSS Boxer 4T
1,800.00EUR

Information

Shipping & Returns
Privacy Notice
Conditions of Use
Financing
Point Program FAQ
Contact Us

We Accept

Quick Find

Shopping Cart

3 x	Balsa panel 2.5x100x1000 mm
1 x	Balsa panel 3.0x100x1000 mm
2 x	Balsa panel 2.0x100x1000 mm
1 x	A/C quality beech plywood 600x300x5.0 mm
1 x	Birch plywood plate 600x300x4.0 mm
3 x	BALSA triangular 15x15x1000 mm
2 x	Balsa panel 6.0x100x1000 mm
1 x	Beech dowels 3.0 x 1000 mm
1 x	A/C quality beech plywood 600x300x0.6 mm
1 x	Balsa panel 4.0x100x1000 mm
2 x	BALSA trip 3.0x3.0x1000 mm
1 x	quality beech plywood BIRCH 600x300x2.0 mm
1 x	Beech dowels 2.0 x 1000 mm
1 x	BALSA trip 5.0x5.0x1000 mm
1 x	Beech dowels 4.0 x 1000 mm
2 x	Balsa panel 1.0x100x1000 mm
2 x	Balsa panel 10x100x1000 mm
1 x	Balsa panel 5.0x100x1000 mm
1 x	BALSA triangular 10x10x1000 mm
1 x	800TVL CMOS camera for FPV
1 x	USB Mini Camera endoscope
1 x	Camera Sony 4140+673 CCD with Built-in 200mw TX + antenna
1 x	Straightened rod Ø 2.0 mm x 1000 mm
1 x	Straightened rod Ø 2.5 mm x 1000 mm
1 x	Straightened rod Ø 8.0 mm x 1000 mm
2 x	Straightened rod Ø 7.0 mm x 1000 mm
1 x	Straightened rod Ø 4.5 mm x 1000 mm
2 x	Brass hexagonal rod Ø 3.5 mm x 1000 mm
2 x	Brass rod Ø 1.5 mm x 1000 mm
1 x	Aluminium rod Ø 4.0 mm x 3000 mm
1 x	Straightened rod Ø 1.0 mm x 1000 mm
2 x	Straightened threaded rod M3 - 1m
1 x	Straightened rod Ø 6.0 mm x 1000 mm
1 x	Bungee HLG Premium
1 x	6 mm blue aluminium threaded horn with patella
1 x	Horn 5/15 with M2 Bearing
1 x	Brass control horn M4 short for wire (4 pcs)
1 x	Horn 6/27 with M3 Bearing
1 x	Birch plywood plate 600x300x2.0 mm
1 x	A/C quality beech plywood 600x300x8.0 mm
1 x	Lite Plywood panel 600x300x3.0 mm
2 x	A/C quality beech plywood 600x300x0.8 mm
1 x	XH female balance (5S) connector (2 pcs)
2 x	Connectors banana oro 6,0 mm Ultralight (M/F)
2 x	30 cm DEANS female connector
1 x	Banna gold connector 2,5 mm (100 M/F pairs)
3 x	Banna gold connector 2,5 mm (M/F)
2 x	Connectors banna oro 8,0 mm 5 pcs(Female)
2 x	XH female balance (4S) connector (2 pcs)
1 x	Connectors banna oro 4 mm (M/F) (ultralight)
3 x	Conector BEC male (10 pcs)
2 x	XH female balance (2S) connector (2 pcs)
2 x	Connectors banna oro 8,0 mm (Male) 5 pcs.
1 x	XH male balance (2S) connector (2 pcs)
3 x	Conector Servo female 4 pines
1 x	Optotronix Aurora Plug
2 x	2 mm male connector (2 pcs) with safety connector
2 x	MPX Sub-D Adaptor
3 x	XH male balance (5S) connector (2 pcs)
2 x	Connectors banna oro 2 mm (M/F)
1 x	Connectors banna oro 3 mm (M/F)
3 x	Gold antispark 5,5 mm plug
3 x	Connector CAN 15
2 x	Connectors banna oro 0,8 mm (M/F)
1 x	EasyFLY Addon
1 x	SIMtransmitter 6 Mode 2
1 x	Simulador RealFlight RF-9.5 S (sin emisora)
2 x	RF9 Flight Simulator with Spektrum Controller
2 x	Interface Realflight Simulator
1 x	Extension 7.5 cm
1 x	Extension silicon 100 cm (Futaba)
1 x	Piloto JET 1:3,5
1 x	Ballast 700gr OPALE
1 x	A/C quality beech plywood BIRCH 600x300x1.0 mm
1 x	Gates hinge aluminium (1 pcs)
1 x	Long ball link M2 (6 uds)
1 x	Support Flush MPX Conector (6 pcs)
1 x	L cockpit anchor "tipe F3A" (2 pcs)
2 x	Straightened threaded rod M2-1m
1 x	Brass rod Ø 0.5 mm x 1000 mm
1 x	Long adjustable control horn 3x34
1 x	Extra long horn 60x30
1 x	LH long black aluminium horn L31xH30 (2pcs)
1 x	Control horn long w/ball
1 x	RH long aluminium horn (2pcs)
1 x	Threaded coupler ALU M3 Ø 6 (2 uds)
1 x	Threaded coupler ALU M2,5 Ø 4 (2 uds)
2 x	Soldering PCBs 8pin, 5 pieces
2 x	XT-60 connector (male)
1 x	Connectors banna oro 6,0 mm (M/F)
1 x	XH male balance (6S) connector (2 pcs)
1 x	Contacto macho pin conector (10 pcs)
3 x	XT-60 connector (female)
1 x	A/C quality beech plywood 600x300x0.8 mm
1 x	BALSA trip 4.0x4.0x1000 mm
1 x	Protector Connector Dean-T (1 pair)
2 x	Conector JR Servo male (10 pcs)
1 x	BALSA trip 2.0x10.0x1000 mm
2 x	XT-90 connector (pair)
3 x	XH female balance (7S) connector (2 pcs)
2 x	MR30 connector male
2 x	Conector JR/Uni Servo male BLUE silicon (10 pcs)
1 x	XH female balance (6S) connector (2 pcs)
1 x	Connectors banna oro 8,0 mm (M/F)
1 x	Connectors MPX male (PIN double)
2 x	CC 03
1 x	Adapter lead MPX/EC3
2 x	30 cm BEC cable (male)
1 x	30 cm BEC cable (female)
1 x	TrainerCord (master-learner)
2 x	Cabel charger transmitter GRAUPNER
1 x	JETImodel SINGLE BEC
1 x	XH male balance (8S) connector (2 pcs)
1 x	Wing conexion 2 servos Futaba 50 cm
1 x	Connectors MPX black male
1 x	MPX screwable clips (4 pcs)
1 x	XT60 Connector with Holder Male 2pcs
1 x	Connectors MPX 8 pins (green) 1 pair (male-female)
1 x	XH female balance (9S) connector (2 pcs)
1 x	Conector XT-150 6mm (Set: 5 pares)
2 x	XT-30 connector (pair)
2 x	2 mm female connector (2 pcs) with safety connector
1 x	MPX Support (2 pcs)
1 x	Conector JR/Uni Servo female BLUE silicon (10 pcs)
2 x	Soporte carbono MR30 (2 pcs)
1 x	Connectors MPX female
3 x	XH female balance (3S) connector (2 pcs)
1 x	PIN Connector female (100 pcs)
1 x	Connectors MPX 8 pins with support (black) 1 pair (male-female)
1 x	A/C quality beech plywood 600x300x6.0 mm
2 x	GameCommander USB Universal
1 x	Propeller Pleg CAM-Prop 10x6 + Spinner
1 x	SD HC 8 GB
1 x	Straightened rod Ø 1.5 mm x 1000 mm
1 x	LA500 Autogyro
1 x	Aluminum Fold Prop Spinner 38 mm / 5 mm
1 x	Brass hexagonal rod Ø 3 mm x 1000 mm
1 x	Straightened rod Ø 5.5 mm x 1000 mm
1 x	2 LiPo XH>EH adapter
1 x	Black copper lacquer wire Ø0,2 mm (5 m)
1 x	PC-6 Pilatus Porter Big "Fredi" (PICHLER)
1 x	Crawler GRE-24 RTR 1:24 Arena
1 x	55 mm aluminium spinner (Kavan)
2 x	Adapter lead MPX/XT60
1 x	Propeller POWER-PROP 12x9
1 x	5 LiPo XH>EH adapter
1 x	Propeller POWER-PROP 10x7 Izda
1 x	TP/TopFuel - XH 2/3S Adapter
1 x	Giant Scale Muffler D.A. 70
1 x	CC 05
1 x	USB HLS prog. interface
1 x	Civilian pilot "Curt" size 9cm (Slimline)
1 x	Civilian pilot "Joe" size 9cm (Slimline)
1 x	Monokote BLUE metalizado (1.8x0.65m)
1 x	3,9 mm ZG20-ZG38 servo arm
1 x	DPS Switch JR/JR
1 x	Cable set PREMIUM, SUB-Done 4three fuselage/wing 160 cm
1 x	Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm)
1 x	Bec MR UBEC 5A (5v/6v/7v)
1 x	MPX housing with flange (4 pcs)
1 x	Wing connector 8pin with pin strip, plug & socket
1 x	Red 4 mm connector holder
1 x	Battery RX JETI LiIon RB 3100 7.2v
1 x	DUPLEX 2,4EX Brackets for Transmitter DC/DS
1 x	resin-hardener package L-385 with hardener H-385
1 x	DUPLEX 2,4GHz MRPM-AC EX
1 x	Wing connector 8pin with pin strip, plug & socket
1 x	Xoar Electric Beechwood Prop 15x8
1 x	Aluminum Fold Prop Spinner 30 mm / 5.0 mm
1 x	Buy Perforated film 100 cm / 50 m
1 x	Sistema LDS - Ø12 mm servos Ø 5/24 spline 95º (MKS) pitch 6 mm
1 x	Carbon Fabric Prepreg 200 g/m² (twill 2/2) 100 cm, roll/ 1 m
1 x	Breatex™ Non-woven absorber 300 g/m² Roll 41 m
1 x	Cessna SKYLANE T182 1.75m - Seagull Model
1 x	Cable coupler M2 (10 uds)
1 x	Ball Link M2 with Ball and Hardware, 10 pcs
1 x	Birch plywood plate 600x300x2.5 mm
1 x	Propeller 12x6 Falcon electric
1 x	Propeller POWER-PROP 14x9
1 x	Propeller POWER-PROP 12x6
1 x	Conector JAPAN G2 Set 5 pares
1 x	PT 21x13 EL Propeller 3 Blade
1 x	30 cm MULTIPLEX female connector
1 x	PT 21x13 EL Propeller
1 x	Pilot "Anthony" (Slimline)
1 x	Pilot "Duke" Legends Series (Slimline)
1 x	Monokote BLANCO jet (1.8x0.65m)
1 x	Monokote ROJO misil (1.8x0.65m)
1 x	Monokote PLATINO metalizado (1.8x0.65m)
1 x	38 mm Alu spinner 5 mm pleg. propeller
1 x
1 x	Socket head long ball link M3 (6 uds)
1 x	CellPRO 4S Adaptader (GP/KO up to 4S)
1 x	Connector Sub-D 2+5 Female

5,535.75EUR