Top » Catalog » Hardware » BEC/Cables/Conectors/Interruptor » ROI142KS

15.06EUR

Opto Gas Engine Kill Switch
[ROI142KS]

This kill switch is Optically Coupled to isolate your ignition system from your radio system. (No Interference!!) this device features the following:

•Includes a remote mountable bright LED to indicate when the ignition is armed.
• Optically Coupled input/output is Isolated.
• 8 Bit PIC Controller.
• Li-Po/Li-Ion/A123/Ni-Mh/NiCad Input.
• Up to 20 Volt 15 amp MOS-FET output.
• DSP Noise/Loss of signal Filtering.
• PPM-PCM 2048 – 1024 & 2.4Ghz Interface Support.
• Low Voltage Drop – Less than 150mv.
• 100% Surface Mount Technology.
• Heavy Gauge Wires, universal connectors.
• Small and light weight – only 12 Grams!

This device plugs into a spare receiver channel.

This is a must have safety device for any gas powered plane! This device allows you to safely kill your engine at anytime (on the ground, or inthe air!)

few units

Reviews

Customers who bought this product also purchased

Cylidric hinge 33 mm Ø 2 mm (5 pcs) few units	MPS Gas-Cap-Powerswitch few units	Propeller MENZ-S 17x10 few units
Propeller MENZ-S 18x12 few units	Tacometer mini ignition RCEXL few units	Cyano SUPER - GOLD™ (12g) few units

Categories

* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->

  3D IMPRESION
  ABS Rods-Strips
  ABS/GFK/CFK plate
  Actuator
  Adapters->
  Adhesives/Resin/Epoxy->
  Altimeters->
  Amperimeters
  Anemometer
  Auto-Pilot
  Bags/Covers
  Batteries->
  BEC/Cables/Conectors/Interruptor
  Bungee Launchers
  Cables
  Cameras->
  Carbon rod
  Carbon/Brass/Steel/ABS/Aluminium
  Catalogues
  Chargers->
  Clevis
  Combustible->
  Connectors
  Control horns
  Controlers->
  Coverings/Thermoretrac
  Decals
  Extension
  Extinguisher
  Ferritas
  Glasses
  Hardware
  Hinges
  Instruments / Panels
  Lights/Ilumination->
  Linkages
  Merchandising
  Motor
  Pilots
  Pinion extractor
  Power supply system/Data Recordi->
  Profiles
  Propelers->
  Screws
  Servos->
  Simulators
  Smoke/Rocketry/Fireworks
  Spinners->
  Spray/Painting/Dope/Solder Paste
  Steel/brass Rod/Aluminium
  Support/CG/Incidenc.
  Tapes/Closed/Bridles
  Tools
  Towing
  Transmitters/Receivers->
  Undercarriage->
  Wheels & Axles->
  Wing Joiner
  Wood
Car/Trucks->
Motors & Turbines->
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA

What's New?

Emisora Spektrum NX10 10ch (solo Tx)
619.92EUR

Information

Shipping & Returns
Privacy Notice
Conditions of Use
Financing
Point Program FAQ
Contact Us

We Accept

Quick Find

Shopping Cart

2 x	Straightened threaded rod M3 - 1m
3 x	Straightened rod Ø 0.5 mm x 1000 mm
2 x	Straightened rod Ø 1.5 mm x 1000 mm
1 x	Straightened threaded rod M2-1m
2 x	Straightened rod Ø 2.0 mm x 1000 mm
3 x	Brass hexagonal rod Ø 4 mm x 1000 mm
2 x	Aluminium rod Ø 4.0 mm x 3000 mm
2 x	Brass rod Ø 1.5 mm x 1000 mm
2 x	Straightened rod Ø 4.5 mm x 1000 mm
4 x	Straightened rod Ø 6.0 mm x 1000 mm
2 x	Brass hexagonal rod Ø 3.5 mm x 1000 mm
2 x	Straightened rod Ø 5.5 mm x 1000 mm
2 x	Straightened rod Ø 3.0 mm x 1000 mm
3 x	Straightened rod Ø 1.0 mm x 1000 mm
3 x	Brass hexagonal rod Ø 3 mm x 1000 mm
3 x	Brass hexagonal rod Ø 5 mm x 1000 mm
2 x	Straightened rod Ø 8.0 mm x 1000 mm
1 x	Straightened rod Ø 1.2 mm x 1500 mm
3 x	Brass rod Ø 0.8 mm x 1000 mm
1 x	DYNAMOMETER S-1580
3 x	Brass rod Ø 0.5 mm x 1000 mm
1 x	Optical RPM Sensor
2 x	Straightened rod Ø 1.5 mm x 1500 mm
2 x	Flat Connector 4.0 mm x 1000 mm
3 x	Streamline Stainless Steel Tubing 10.5x5.7x1000 m
2 x	ABS angle 1.5x1.5x1000 mm
2 x	Streamline Stainless Steel Tubing 12.3x7.7x1000 mm
3 x	ABS "T" angle 10.0x10.0x1000 mm
2 x	ABS angle 6,0x6,0x1000 mm
1 x	ABS angle 2,0x2,0x1000 mm
1 x	Streamline Stainless Steel Tubing 7.5x4.5x1000 mm
1 x	Cross Connector 4.0 mm x 1000 mm
2 x	ABS "T" angle 2.0x2.0x1000 mm
2 x	Streamline Stainless Steel Tubing 15.5x8.5x1000 mm
3 x	Streamline Stainless Steel Tubing 19.5x9.8x1000 mm
1 x	Streamline Stainless Steel Tubing 6.3x3.5x1000 mm
2 x	ABS angle 3,0x3,0x1000 mm
1 x	Streamline Stainless Steel Tubing 14.5x9.6x1000 mm
2 x	Profile ABS half cane 2.0x1000 mm
1 x	Cabel charger transmitter GRAUPNER
1 x	MPX-Dean "T" Adapter
1 x	Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm)
1 x	Adapter lead MPX/XT60
1 x	CM-3
1 x	JETImodel SINGLE BEC
1 x	APM2.6 Power module with 5.3V DC BEC
1 x	Red copper lacquer wire Ø0,2 mm (5 m)
1 x	TP/TopFuel - JST-EH 4/5S Adapter
1 x	30 cm BEC cable (male)
1 x	Circlick securite
1 x	Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm)
1 x	DUPLEX USBa USB-Adapter for Jeti Duplex Items
1 x	Balance "Y" Wire 6S, 2x JST-XH / 1x JST-EH
1 x	30 cm BEC cable (female)
1 x	CC 05
1 x	Cabel charger battery transmiter Futaba 2x0,5 qmm (50 cm)
1 x	Bungee HLG Premium
1 x	Dean "T" - Futaba Adapter
1 x	Copper lacquer wire Ø0,2 mm (5 m)
1 x
2 x	Ring 320 mm length (5 pcs)
1 x	SE Ring 240 mm (2 pcs)
1 x	SE Ring 250 mm (2 pcs)
1 x	20x200 mm battery rings
2 x	10 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x	5 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x	RUDDOG Protection and Heat Shield Tape (2mx50mm)
1 x	13 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	SE Ring 360 mm (2 pcs)
1 x	Spikes Band (5 m)
1 x	26 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	SE Ring 480 mm (2 pcs)
1 x	Tape GFK 38 mm
1 x	Tape GFK 50 mm
2 x	SE Ring 300 mm (2 pcs)
1 x	SE Ring 400 mm (2 pcs)
1 x	Cable-Tie 1.66x71mm / 0.07x2.8″ (20 pcs)
1 x	USB Mini Camera endoscope
1 x	Stainless steel cable Ø 0.62 mm (10 m)
1 x	Screw-lock pushrod conn snap Ø 1.5 mm (2 uds)
1 x	Brass rod Ø 1.0 mm x 1000 mm
1 x	Surface Indicator Gauge Small
1 x	Straightened rod Ø 2.5 mm x 1000 mm
1 x	ABS angle 5,0x5,0x1000 mm
3 x	L-Connector 1.0 mm x 1000 mm
1 x	ABS rectangular profile 12x6.0x1000 mm
1 x	L-Connector 1.5 mm x 1000 mm
1 x	Profile ABS half cane 2.5x1000 mm
2 x	Profile ABS Square 1 x 1000 mm
1 x	U Profile ABS 2,0x4,0x1000 mm
1 x	T-Connector 4.0 mm x 1000 mm
2 x	Profile ABS triangular 4.0x1000 mm 60º
2 x	U Profile ABS 1,0x2,0x1000 mm
1 x	L-Connector 4.0 mm x 1000 mm
2 x	ABS rectangular profile 10x5.0x1000 mm
1 x	Profile ABS half cane 4x1000 mm
2 x	Profile ABS half cane 3x1000 mm
1 x	Profile ABS Square 3 x 1000 mm
2 x	Motor Eachine Racer 250 Brushless Motor - BG2204 2300kv - CCW th
1 x	Straightened rod Ø 7.0 mm x 1000 mm
1 x	Male Prolonger TP 4/5S
1 x	Super Light Wheels(Sponge Tyre) Ø 65mm x 19mm (2pcs) axis Ø 3.5m
1 x	Wheel FEMA 178 mm / 8 mm
1 x	Wheel 115 mm with electromagnet and brake disk (2 uds)
1 x	4 blades set
1 x	Interruptor RX/Batterie
1 x	Wheel Ø 90 mm (1 ud) Electron Retracts
1 x	Magnetic Interruptor MULTIPLEX
1 x	Aluminun wheel collar 2.5 mm Ø (4 uds)
1 x	Tail tube RAINBOW
1 x	Blade Holder Full (3 blades)
1 x	Interruptor SAFET-SWITCH 12HV Twinbatt
1 x	Autogyro Cierva C30 Spain
1 x	Mudguard for 140/165 mm wheels
1 x	STEERING FRONT WHEEL SYSTEM BIDULE 111
1 x	Wing bolts M6 Steel screw Red (2 pcs)
1 x	Vertical cockpit anchor "tipe F3A" (2 pcs)
1 x	Tip wing protector 28x10x12 (2 pcs)
2 x	Wheel collar 5 mm Ø (4 uds)
1 x	STEERING FRONT WHEEL SYSTEM BIDULE 55
1 x	Snap pin for micro clevis (10 uds)
1 x	Stainless steel cable Ø 0.88 mm - 60 kp (10 m)
1 x	Stainless steel cable Ø 0.5 mm (20 m)
1 x	Stainless steel cable Ø 1.3 mm (10 m)
1 x	Kit hydraulic brake
2 x	13 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x	Robbe Modellsport ROOKIE 35 ESC FOR BRUSH MO TORS
1 x	Aqua RACE 70 (without motor)
1 x	Motor ACTRO 50-2-760
1 x	Horn 16,5x20 mm (2 pcs)
1 x	Horn 5/20 with M2 Bearing
1 x	20 mm carbon horn
1 x	Steering arm 12 mm Ø 4 mm
1 x	Window mounting channel 5m
1 x	Stainless steel cable Ø 0.5 mm (2 m)
1 x	Extension 6 lipos XH > EH
1 x	89x32 mm (3.5") axle Ø5 mm aluminium core wheel
1 x	Aluminun wheel collar 6 mm Ø (4 uds)
1 x	MPS Gas-Cap-Powerswitch
1 x	Female prolonguer XH 30 cm 6 cell cable of silicone 0,25 mm
1 x	Wheel FEMA 82 mm / 5 mm
1 x	69x25 mm (2.75") axle Ø4 mm aluminium core wheel
1 x	Nose wheel 62 mm
1 x	102x26 Ø6.0 mm aluminium core wheel
1 x	Male/Female prolonguer for Balancer Thunder Power 6S
1 x	Prolonguer for Balancer Thunder Power 6S
1 x	Screw M3x16
1 x	Head upper part
1 x	Blade holder center
1 x	Head lower part
1 x	Ball joint long
1 x	Waterproof adhesive tape, width 19mm, length 25m
1 x	SE Ring 200 mm (2 pcs)
1 x	Straightened rod Ø 5.0 mm x 1000 mm
1 x	Hard brass tubing (L 1000 mm, Ø14.0 mm, Ø12.0 mm)
1 x	Profile ABS triangular 6.0x1000 mm 90º
1 x	ABS angle 4,0x4,0x1000 mm
1 x	Sebart 2.2 m WHITE/BLUE (SebART)
1 x	Streamline Stainless Steel Tubing 9.0x5.0x1000 mm
2 x	Profile ABS half cane 4x2.5x1000 mm
1 x	Rubber profile 6-2 mm 2M
1 x	Profile ABS Square 2 x 1000 mm
1 x	Profile ABS triangular 4.0x1000 mm 90º
1 x	U Profile ABS 5,0x10,0x1000 mm
2 x	Profile ABS half cane 8.0x1000 mm
1 x	ABS "T" angle 8.0x8.0x1000 mm
1 x	Profile ABS half cane 7.0x1000 mm
1 x	Sukhoi 29S 2,6 m Yellow/Black (SebART)
1 x	EDGE 540-A 74" (1880 mm)
1 x	EDGE 540-A 105" (2660 mm)
1 x	ULTRA STICK 30 cc ARF
1 x	EXTRA NG 74" white/red/blue (Skywing RC)
1 x	U Profile ABS 8,0x4,0x1000 mm
1 x	Brass control horn M2 short for wire (2 pcs)
1 x	Horn 20x28,5 mm (2 pcs)
1 x	Horn DUBRO 1/2A
1 x	Horn 13,5x16 mm (2 pcs)
1 x	SUS wire 3m (nylon coated)
1 x	6 mm red aluminium threaded horn with patella

8,744.53EUR