Top » Catalog » Hardware » Power supply system/Data Recordi » Emcotec » EMCA15055

149.95EUR

DPSI Ampere & Voltage bundle
[EMCA15055]

DPSI Ampere & Voltage bundle

Product description
DPSI Ampere - Produktbeschreibung
Powerful battery backer with peak current capacity of up to 60 ampere. The DPSI Ampere & Voltage bundle can be used as dual power supply for receivers, turbines or similar electric consumers of R/C models.
System stability of the DPSI Ampere & Voltage bundle is ensured by connecting two batteries. If one battery fails, safe operation is guaranteed by the second battery. Normally, both batteries are discharged symmetrically and simultaneously (at the same time). Due to the parallel connected batteries the current is split in half for each battery.
The DPSI Ampere & Voltage bundle is switched ON/OFF electronically by placing a magnet on the corresponding position on the device housing.
The DPSI Ampere & Voltage bundle can handle a permanent current of 50 ampere. So it is the perfect solution for all high current applications. Thanks to an integrated charging connector both connected batteries can be charged simultanously with only one charging device.
The DPSI Ampere & Voltage bundle is the first EMCOTEC battery backer that can be operated with 3S LiPo batteries or batteries with voltages up to 13.2 volts. So the module is much more than a conventional dual power supply for receivers. Due to the higher voltage also devices such as turbines can be reliably powered with the DPSI Ampere & Voltage bundle.
Function overview
Loss-free switching function without diodes.
Integrated electronically fail-proof switches separately for each battery without using the micro controller (CSHC).
Dual safeguarded power off logic. Even a failing part does not lead to a power out.
IVM (Intelligent Voltage Monitoring). Battery voltage monitoring with acoustic warning signals for all supported battery types (NiMH, LiIon, LiPo, LiFePO4).
Booster for safe control of the power switches even at extremely low voltages or short power interruptions (MBOOST).
DPSI Voltage - Product description
Voltage regulator module for battery backer DPSI Ampere.
The module must be plugged to the output side of the DPSI Ampere. With a jumper regulated output voltages of 6 volts, 6.6 volts or 7.2 volts can be selected. Furthermore the unregulated battery voltage can be used additionally on a secound output.
Delivery includes dual power supply DPSI Ampere, voltage regulator DPSI Voltage, programming jumper, switching magnet with EMCOTEC patch as well as German and English operating instructions.

under request

Reviews

Categories

* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->

  3D IMPRESION
  ABS Rods-Strips
  ABS/GFK/CFK plate
  Actuator
  Adapters->
  Adhesives/Resin/Epoxy->
  Altimeters->
  Amperimeters
  Anemometer
  Auto-Pilot
  Bags/Covers
  Batteries->
  BEC/Cables/Conectors/Interruptor
  Bungee Launchers
  Cables
  Cameras->
  Carbon rod
  Carbon/Brass/Steel/ABS/Aluminium
  Catalogues
  Chargers->
  Clevis
  Combustible->
  Connectors
  Control horns
  Controlers->
  Coverings/Thermoretrac
  Decals
  Extension
  Extinguisher
  Ferritas
  Glasses
  Hardware
  Hinges
  Instruments / Panels
  Lights/Ilumination->
  Linkages
  Merchandising
  Motor
  Pilots
  Pinion extractor
  Power supply system/Data Recordi->
    Bavarian Demon
    Dymond
    Eagle Tree
    Emcotec
    Futaba
    Jeti
    PowerBoxSystems
    ROI IMPORT
    SebART
    Setlo
  Profiles
  Propelers->
  Screws
  Servos->
  Simulators
  Smoke/Rocketry/Fireworks
  Spinners->
  Spray/Painting/Dope/Solder Paste
  Steel/brass Rod/Aluminium
  Support/CG/Incidenc.
  Tapes/Closed/Bridles
  Tools
  Towing
  Transmitters/Receivers->
  Undercarriage->
  Wheels & Axles->
  Wing Joiner
  Wood
Car/Trucks->
Motors & Turbines->
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA

What's New?

PT-22 Ryan Recruit 2290 mm (SEAGULL)
560.00EUR

Information

Shipping & Returns
Privacy Notice
Conditions of Use
Financing
Point Program FAQ
Contact Us

We Accept

Quick Find

Shopping Cart

4 x	7 Servo SET 9g DS MG + Full servo extension cable set for Avanti
1 x	SERVO DES 568 MG
2 x	SERVO DES 707 BB MG
2 x	Soporte metal para servos
3 x	SERVO DES 806 Pignons
2 x	SERVO DES 658 BB MG
2 x	Straightened rod Ø 5.0 mm x 1000 mm
1 x	Straightened rod Ø 1.0 mm x 1000 mm
1 x	Straightened rod Ø 1.5 mm x 1000 mm
1 x	Straightened rod Ø 3.0 mm x 1000 mm
1 x	Straightened rod Ø 0.5 mm x 1000 mm
1 x	120x60 mm SLH KOVO wheel
1 x	Horns set HS-65HB/MG, 5065MG
1 x	800TVL CMOS camera for FPV
1 x	Camera Sony 4140+673 CCD with Built-in 200mw TX + antenna
1 x	Servo MKS HV1220
1 x	Servo Metal Horn 15.5 mm MKS
2 x	Brazo servo MKS X8 Metal L:1.25/1.5 inc
1 x	Servo MKS HV6120H
1 x	Servo MKS 6100 DS
2 x	Servo MKS HBL380
1 x	HV6150 Digital Servo
1 x	Servo MKS HBL599 SL
2 x	Servo MKS HV747
1 x	Servo MKS HBL550
1 x	Ventus 1:4 set of instruments
1 x	Servo MKS HV6130
1 x	Brazo servo MKS Metal M3-L:30 (2 pcs)
1 x	Flat washer 1.7 mm (20 pcs)
1 x	Screw-lock connector Ø 2 mm (2 uds)
1 x	Aluminium cap bolt washer M4 blue (8 pcs)
1 x	Locking cable tie 2.5x100 (uds)
1 x	Lock washer 2.7 mm (20 pcs)
1 x	Aluminium wide washer M4 Blue (4 pcs)
2 x	Cap closure 33/23.5mm (2 uds)
1 x	Stainless steel cable Ø 0.5 mm (20 m)
1 x	Steering arm 16 mm Ø 3 mm
1 x	Stainless steel cable Ø 0.5 mm (2 m)
1 x	Aluminium wide washer M3 gold (4 pcs)
1 x	Lock washer 3.2 mm (20 pcs)
1 x	Electric spoiler 250 mm (2 pcs)
1 x	Screw-lock connector M2 (2 uds)
1 x	Micro screw-lock pushrod conn snap Ø 1 mm (2 uds)
1 x	Aluminium cap bolt washer M3 red (8 pcs)
1 x	Quicklock washer 1.5 mm (10 pcs)
1 x	Quicklock washer 4 mm (10 pcs)
1 x	Crimping sleeves for cable 1.3 mm (10 pcs)
1 x	Quicklock washer 3 mm (10 pcs)
2 x	Steering arm 12 mm Ø 3 mm (2 uds)
1 x	Spring lock washer 2.6 mm (20 pcs)
1 x	Flat washer 4.3 mm (20 pcs)
1 x	One touch canopy lock
1 x	Aluminium cap bolt washer M4 red (8 pcs)
1 x	Lock washer 2.2 mm (20 pcs)
1 x	Circlik for shaft 1.9 mm (10 pcs)
1 x	Circlik for shaft 1.5 mm (10 pcs)
1 x	Aluminium cap bolt washer M4 green (8 pcs)
1 x	Steering arm 16 mm Ø 4 mm (2 uds)
1 x	Flat washer 2.7 mm (20 uds)pcs)
1 x	Spring lock washer 3.1 mm (20 pcs)
1 x	Aluminium wide washer M3 red (4 pcs)
2 x	Crimping sleeves for cable 0.85 mm (10 pcs)
1 x	Horn 5/20 with M2 Bearing
1 x	Simulador RealFlight RF-9.5 S (sin emisora)
2 x	Tapa estado carga XT-60 (6 pcs)
1 x	Actuador lineal HLS12-100210-7.4v
2 x	Support pump Xicoy X45
1 x	Support Antena 2.4 Ghz (2 pcs)
1 x	Landing gear axle Ø 6 mm (2 uds)
1 x	Landing gear axle Ø 5 mm (2 uds)
1 x	Landing gear axle 4x21 4 mm (2 uds)
1 x	45x19 mm hard foam KOVO wheel (2 pcs)
1 x	Fully Threaded Steel Rod Duralumin 40 mm M3 (2 pcs)
1 x	Fully Threaded Steel Rod Duralumin 80 mm M3 (2 pcs)
1 x	Crystal Universal RX 35.070 Ch 67
1 x	Canopy Lock V1 M3 Blue (2 pcs)
1 x	43x14 mm hard foam KOVO wheel (2 pcs)
1 x	64x20 mm (2.5") Type jets aluminium core wheel
2 x	2.5 inch aluminium core wheel (1 pcs)
1 x	80x40 mm hard foam KOVO wheel
1 x	Brass hexagonal rod Ø 3 mm x 1000 mm
1 x	Brass rod Ø 1.5 mm x 1000 mm
1 x	Brass rod Ø 0.5 mm x 1000 mm
1 x	SERVO DES 707 BB MG, Pignons
1 x	Straightened rod Ø 14.0 mm x 1000 mm
1 x	Brass hexagonal rod Ø 4 mm x 1000 mm
1 x	Straightened rod Ø 4.5 mm x 1000 mm
1 x	Anntena Panel 5,8 GHz - 14 dBi
1 x	Servo arms set HS-65HB/MG/5065MG
1 x	Fast attachment for servos (25 pcs)
1 x	Servo DL3017 Digi 17Kg-0.15s/60º
1 x	25 mm carbon servo arm
1 x	Servo MKS 6100 DS
1 x	SERVO DES 588 BB MG
1 x	Control for forward wheel (MINI)
1 x	Aluminun wheel collar 5 mm Ø (4 uds)
1 x	Fully Threaded Steel Rod alumin 100 mm M3 (2 pcs)
1 x	Screw M3x16 (10 pcs)
1 x	Circlik for shaft 2.3 mm (10 pcs)
1 x	Fully Threaded Steel Rod Duralumin 130 mm M3 (2 pcs)
1 x	Crystal TX 35.010 Ch 61
1 x	Allen wheel collar M3x5
1 x	Screw M2.5x8 (10 pcs)
1 x	Hexagonal Nut M4 (10 pcs)
1 x	Lead with adhesive (2 pcs)
1 x	Fully Threaded Steel Rod alumin 60 mm M2,5 (2 pcs)
1 x	Floating M4 washer pad (36 pcs)
1 x	11 mm Rubber pads (14 pcs)
1 x	Split M1,2x10 (10 pcs)
1 x	140 mm rods set for direction control
1 x	Canopy Latch
1 x	Fully Threaded Steel Rod alumin 90 mm M3 (2 pcs) knurled
1 x	Support FUEL DOT V3
1 x	Soporte grifo FESTO vertical (1 pcs)
1 x	Aro pasacable Ø20 mm (4 pcs)
1 x	Angle support XT60 conector
1 x	Support pumb/filter Xicoy X45
1 x	Servo HBS 690BB HV Digital
1 x	SERVO DES 806 Pignons
1 x	Aluminun wheel collar 6 mm Ø (4 uds)
1 x	50 mm servo arm with bearing (2 pcs)
1 x	Super Light Wheels(Sponge Tyre) Ø 55mm x 19mm (2pcs) axis Ø 3.5m
1 x	40 mm servo arm with bearing (2 pcs)
1 x	FEMA DEFLECTOR LEVER FOR WHEEL BRAKE,
1 x	Tail wheel for 8-12 kg models
1 x	Tail gear set (60-120 class)
1 x	Tailwheel for 40/90 size
1 x	Deposito DUBRO 1800cc-60oz
1 x	Wheel Scale 1/4 Vintage 178 mm / 7" (1 par)
1 x	Single rim type C3 36/33,5/18,5 mm (pneumatics 55-70 mm)
1 x	DUBRO - CUB WHEELS (1/3 SCALE) (558TLC) - 2PCS
1 x	Wheel FEMA 100 mm / 6 mm
1 x	70x23 Ø3.5 mm aluminium core wheel
1 x	4" - 102 x 45 mm Ø5 mm aluminium core wheel
1 x	Wheel FEMA 178 mm / 8 mm
1 x	Super Light Wheels (Sponge Tyre) Ø 60mm x 19 mm (2pcs) axis Ø 3.
1 x	Wheel 115 mm with electromagnet and brake disk + E-Brake (2 uds)
1 x	Black tray 2,4EX DC-16/14/24 black
1 x	Switch Spring-Loaded 2-Position DC Tx DUPLEX 2,4EX
1 x	Stick with Button DC/DS-16/14/24 Tx DUPLEX 2,4EX
1 x	Teacher / Student Cable
1 x	Bag JETI Duplex
1 x	Caps multicolor Switch JETI
1 x	PPM to Jack link - Tx Black (mono) DC/DS Tx DUPLEX 2,4EX
1 x	ABS tube 16.0x14.0x1000 mm
1 x	ABS tube 18.0x16.0x1000 mm
1 x	ABS tube 14.0x10.0x1000 mm
1 x	ABS rectangular profile 10x5.0x1000 mm
1 x	ABS I Strip 10x5x1000 mm
1 x	ABS "T" angle 10.0x10.0x1000 mm
1 x	Oracover light Grey 2m
1 x	Spinner NUT M10x1
1 x	Axi for motor A40-L Motor 8-Pole-Electric Turbine
1 x	Aluminium Hub for folding Props 55 mm M8 Shaft 6 mm
1 x	VM 2014/27 rear
1 x	Medidor ángulos y/o incidencias
1 x	DPSI LR-S (with push buttons)
1 x	Optotronix X-Carrier
1 x	Tip wing protector 40x14 (2 pcs)
1 x	DPSI V-Match
1 x	100 Newtons FEMA absorber
1 x	Compact on-board starting system (9724)
1 x	Servo holder for retract
1 x	Gearwheel 9724/09 for ZG 45
1 x	Landing gear axle Ø 8 mm (2 uds)
1 x	Glider retract undercarriage 8-16 Kg 2.5-3.2(140 mm wheel with b
1 x	Restrictor FESTO 3/3 mm
1 x	2,3 mm Prop Adapter M6
1 x	300x4 mm M4 shaft ship
1 x	16x10 tree blades propeller Master Airscrew
1 x	2,3 mm Prop Adapter M6
1 x	15x7 tree blades propeller LEFT
1 x	25 mm fenders (10 pcs)
1 x	29,0 mm propeller (left propeller)
1 x	31,0 mm propeller (rigth propeller)
1 x	JETI Counter for DC-16 (Blue)
1 x	DUPLEX 2,4EX Stick with 2-Position Switch for Transmitter DC/DS
1 x	DUPLEX 2,4EX Stick with 3-Position Switch for Transmitter DC/DS
1 x	RC Power Switch 5A
1 x	DUPLEX 2,4EX Switch SAFETY 2-Position Safety DC-16/14
1 x	Switch Nutspanner for JETI Duplex Transmitter DC / DS
1 x	DC24 II Transmitter case insert
1 x	ABS angle 5,0x5,0x1000 mm
1 x	ABS angle 4,0x4,0x1000 mm
1 x	ABS "T" angle 6.0x6.0x1000 mm
1 x	ABS Strip 1.0x5.0x1000 mm
1 x	ABS tube 3.0x1.0x1000 mm
1 x	ABS angle 3,0x3,0x1000 mm
1 x	ABS "T" angle 4.0x4.0x1000 mm
1 x	ABS Strip 1.5x2.0x1000 mm
1 x	ABS Strip 1.5x6.0x1000 mm
1 x	ABS Strip 1.5x8.0x1000 mm
1 x	Oracover Black 10 m
1 x	Oratex Yellow Cub 10 m
1 x	Oratex Antik 2m
1 x
1 x	Sun Cover ULTIMATUM 2.0 (Hispano Aviacion)
1 x	Sun Cover BULL Mo1 2.6 (Hispano Aviacion)
1 x	Esc master MEZON 120 Lite
1 x	Propeller APC 12x3.8 SF
1 x	Propeller APC 12x8 SF
1 x	Battery LiFe TopFuel 3100 mAh 4s MTAG 30C
1 x	Propeller APC 10x6 Electric
1 x	Propeller APC 12x6 Electric Pusher
1 x	Propeller APC 11x4.7 SF
1 x	Propeller APC 10x4.7 SF
1 x	AXI 2814/20 V2
1 x	AXI 2826/10 V2
1 x	AXI 2826/6 V2
1 x	AXI 2814/12 V2 Long
1 x	AXI 2826/12 V2
1 x	41x5,5 mm wires output (2 pcs)
1 x	DPSI Micro - DualBat 5.9V / 7.2V JR-JR (Dual Power Supply)
1 x	Tip wing protector 28x10x12 (2 pcs)
1 x	Winter-Glove DS tx
1 x	Winter Glove for DC
1 x	38x4,5 mm wires output (2 pcs)
1 x	Steering arm 16 mm Ø 4 mm
1 x	Landing gear frontal support 29x26x13,5
1 x	Split pin 1.6x16 mm (10 uds)

7,699.83EUR