Top » Catalog » Hardware » Power supply system/Data Recordi » Emcotec » EMCA15055

149.95EUR

DPSI Ampere & Voltage bundle
[EMCA15055]

DPSI Ampere & Voltage bundle

Product description
DPSI Ampere - Produktbeschreibung
Powerful battery backer with peak current capacity of up to 60 ampere. The DPSI Ampere & Voltage bundle can be used as dual power supply for receivers, turbines or similar electric consumers of R/C models.
System stability of the DPSI Ampere & Voltage bundle is ensured by connecting two batteries. If one battery fails, safe operation is guaranteed by the second battery. Normally, both batteries are discharged symmetrically and simultaneously (at the same time). Due to the parallel connected batteries the current is split in half for each battery.
The DPSI Ampere & Voltage bundle is switched ON/OFF electronically by placing a magnet on the corresponding position on the device housing.
The DPSI Ampere & Voltage bundle can handle a permanent current of 50 ampere. So it is the perfect solution for all high current applications. Thanks to an integrated charging connector both connected batteries can be charged simultanously with only one charging device.
The DPSI Ampere & Voltage bundle is the first EMCOTEC battery backer that can be operated with 3S LiPo batteries or batteries with voltages up to 13.2 volts. So the module is much more than a conventional dual power supply for receivers. Due to the higher voltage also devices such as turbines can be reliably powered with the DPSI Ampere & Voltage bundle.
Function overview
Loss-free switching function without diodes.
Integrated electronically fail-proof switches separately for each battery without using the micro controller (CSHC).
Dual safeguarded power off logic. Even a failing part does not lead to a power out.
IVM (Intelligent Voltage Monitoring). Battery voltage monitoring with acoustic warning signals for all supported battery types (NiMH, LiIon, LiPo, LiFePO4).
Booster for safe control of the power switches even at extremely low voltages or short power interruptions (MBOOST).
DPSI Voltage - Product description
Voltage regulator module for battery backer DPSI Ampere.
The module must be plugged to the output side of the DPSI Ampere. With a jumper regulated output voltages of 6 volts, 6.6 volts or 7.2 volts can be selected. Furthermore the unregulated battery voltage can be used additionally on a secound output.
Delivery includes dual power supply DPSI Ampere, voltage regulator DPSI Voltage, programming jumper, switching magnet with EMCOTEC patch as well as German and English operating instructions.

under request

Reviews

Categories

* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->

  3D IMPRESION
  ABS Rods-Strips
  ABS/GFK/CFK plate
  Actuator
  Adapters->
  Adhesives/Resin/Epoxy->
  Altimeters->
  Amperimeters
  Anemometer
  Auto-Pilot
  Bags/Covers
  Batteries->
  BEC/Cables/Conectors/Interruptor
  Bungee Launchers
  Cables
  Cameras->
  Carbon rod
  Carbon/Brass/Steel/ABS/Aluminium
  Catalogues
  Chargers->
  Clevis
  Combustible->
  Connectors
  Control horns
  Controlers->
  Coverings/Thermoretrac
  Decals
  Extension
  Extinguisher
  Ferritas
  Glasses
  Hardware
  Hinges
  Instruments / Panels
  Lights/Ilumination->
  Linkages
  Merchandising
  Motor
  Pilots
  Pinion extractor
  Power supply system/Data Recordi->
    Bavarian Demon
    Dymond
    Eagle Tree
    Emcotec
    Futaba
    Jeti
    PowerBoxSystems
    ROI IMPORT
    SebART
    Setlo
  Profiles
  Propelers->
  Screws
  Servos->
  Simulators
  Smoke/Rocketry/Fireworks
  Spinners->
  Spray/Painting/Dope/Solder Paste
  Steel/brass Rod/Aluminium
  Support/CG/Incidenc.
  Tapes/Closed/Bridles
  Tools
  Towing
  Transmitters/Receivers->
  Undercarriage->
  Wheels & Axles->
  Wing Joiner
  Wood
Car/Trucks->
Motors & Turbines->
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA

What's New?

SAVAGE Max Red 1080 mm
129.90EUR

Information

Shipping & Returns
Privacy Notice
Conditions of Use
Financing
Point Program FAQ
Contact Us

We Accept

Quick Find

Shopping Cart

2 x	80 mm rods set for direction control
2 x	Allen wheel collar M4x6
2 x	Canopy Lock V1 M3 Blue (2 pcs)
2 x	28x5 mm wires output (2 pcs)
2 x	100 mm rods set for direction control
1 x	Allen wheel collar M3x5
2 x	Cable grommet 9.5 mm (4 uds)
2 x	Aluminun wheel collar 5 mm Ø (4 uds)
2 x	Cable grommet Ø 6.4 mm (4 uds)
1 x	41x5,5 mm wires output (2 pcs)
2 x	Aluminun wheel collar 2 mm Ø (4 uds)
1 x	Canopy Lock V1 M3 Red (2 pcs)
2 x	250 mm / 16 mm Airbrakes
2 x	38x4,5 mm wires output (2 pcs)
1 x	Aluminun wheel collar 3.5 mm Ø (4 uds)
2 x	Cable grommet Ø 4 mm (4 uds)
2 x	Aluminun wheel collar 3 mm Ø (4 uds)
2 x	140 mm rods set for direction control
2 x	Aluminium alloy coupler for carbon tube 6/M4
1 x	Cable tie mounts 4.3 (4 uds)
2 x	45 mm rods set for direction control
2 x	45 mm rods + T patellas set for direction control
1 x	90 mm rods + T patellas set for direction control
2 x	Cable grommet Ø 3.2 mm (4 uds)
1 x	Cockpit aluminium closing
1 x	100 mm rods + T patellas set for direction control
2 x	Cable grommet Ø 5 mm (4 uds)
3 x	Cabin latch Fox MDM1 4m (pair)
1 x	Aluminun wheel collar 6 mm Ø (4 uds)
2 x	140 mm rods + T patellas set for direction control
1 x	Cierre cabina aluminio Ø5, I=16 mm
1 x	Allen wheel collar M4x4
1 x	Cap closure 33/23.5mm (2 uds)
1 x	Aluminun wheel collar 2.5 mm Ø (4 uds)
1 x	Allen wheel collar M3x3
1 x	Clip mini fixing for wing (2 pcs)
1 x	Stickers-digit for marking
1 x	Pushrod greyline 3/2 with coupler M2 L: 1000 mm
1 x	Split M1,2x10 (10 pcs)
1 x	Stainless steel cable Ø 0.5 mm (20 m)
1 x	Press fitting for 0,5 diam. steel cable (10 pcs)
1 x	Fully Threaded Steel Rod M3
1 x	Stainless steel cable Ø 0.5 mm (10 m)
1 x	Horizontal cockpit anchor "tipe F3A" (2 pcs)
1 x	Pushrod greyline 3/2 with coupler M3 L: 1000 mm
1 x	One touch canopy lock
1 x	Pushrod greyline 4/3 with coupler M3
1 x	Snap short M2 (10 uds)
1 x	Fully Threaded Steel Rod SUS303 65 mm M3 (2 pcs)
1 x	Pushrod octagone 3/2 with coupler M2
1 x	Screw-lock connector Ø 2 mm (2 uds)
1 x	Landing gear frontal support 29x26x13,5
1 x	Micro screw-lock pushrod conn snap Ø 1 mm (2 uds)
1 x	Snap long M2 (10 uds)
1 x	Snap pin for micro clevis (10 uds)
1 x	Fully Threaded Steel Rod M2,5 (2 uds)
1 x	White smoke canister 100 g
2 x	Ventral support for AX-18/AX-60
1 x	White smoke canister 65 g
1 x	SE Ring 350 mm (2 pcs)
2 x
1 x	Spikes Band (5 m)
1 x	Cinta Goldfix 1m
1 x	20x200 mm battery rings
1 x	Steering arm 12 mm Ø 4 mm
1 x	STEERING FRONT WHEEL SYSTEM BIDULE 55
1 x	Wheel collar 3 mm Ø (4 uds)
1 x	Triple rod con. 2mm Pushrod (2 pcs)
1 x	Steering arm 16 mm Ø 3 mm (2 uds)
1 x	Steering arm 12 mm Ø 4 mm (2 uds)
1 x	Wheel collar 6 mm Ø (4 uds)
1 x	Steering arm 12 mm Ø 3 mm (2 uds)
1 x	SUS wire 3m (nylon coated)
1 x	Triple rod con. 3mm Pushrod (2 pcs)
1 x	Steering arm 16 mm Ø 4 mm
1 x	Window mounting channel 5m
1 x	Stainless steel cable Ø 0.88 mm - 60 kp (10 m)
1 x	Stainless steel cable Ø 1.3 mm (10 m)
1 x	Wheel collar 3.5 mm Ø (4 uds)
2 x	Stainless steel cable Ø 0.52 mm - 15 kp (10 m)
1 x	Wing bolts M3 Steel screw Red (2 pcs)
1 x	Tip wing protector 28x10x12 (2 pcs)
1 x	Wing bolts M6 Steel screw Blue (2 pcs)
1 x	5 mm M2 variable inclined horn
1 x	6 mm M3 variable horn
1 x	Horn with ball 40x30
1 x	Horn micro type4 Ø 0,5 (2 pcs)
1 x	Horn 20x28,5 mm (2 pcs)
1 x	Horn DUBRO 1/2A
1 x	Horn 6/35 with M3 Bearing
1 x	Horn for flap control (1 pcs)
1 x	Horn F3A de Titanium 16 mm (2 units)
1 x	Extra long horn 60x30
1 x	Brass control horn M2 large for wire (2pcs)
1 x	6 mm red aluminium threaded horn with patella
1 x	Horn 5/20 with M2 Bearing
1 x	Extra-long adjustable aluminium control horn 2,8x34
1 x	Horn mando small (2 pcs)
1 x	Ball link Aluminio M4 x 4 x 6 x 26mm (4 uds)
1 x	Kwik link AL Ø2 mm L:23 mm (2 pcs) + Pin Ø 1,6 mm
1 x	100m servo "Premium" wire (white/red/blue)
1 x	PPM Encoder Module
1 x	L-Connector 1.5 mm x 1000 mm
1 x	Fully Threaded Steel Rod SUS303 70mm M3 (2 pcs)
1 x	L cockpit anchor "tipe F3A" (2 pcs)
1 x	Z type of cable coupler Ø 1 (2 uds)
1 x	Horn with ball 55x40
1 x	Small aluminium horn gold (2pcs)
1 x	LH long black aluminium horn L31xH30 (2pcs)
1 x	Pegamento Pu R 50g polyuretano
1 x	resin-hardener package L-385 with hardener H-385 (3.5 Kg)
1 x	LA500 freewheel bearing
1 x	Epoxy Resin L 285 + Hardener 386, kit/ 675g
1 x	White smoke bombs AX-9 (10 pcs)
1 x	14x60 mm Mini rings Tie Wraps (4 pcs)
1 x	Tape GFK 50 mm
1 x	AX-60 starters (5 pcs)
1 x	Super Light Wheels(Sponge Tyre) Ø 65mm x 19mm (2pcs) axis Ø 3.5m
1 x	Green smoke canister 140 g
1 x	Mixers smoke bombs AX-60 (5 pcs)
1 x	Wheel FEMA 140 mm / 6 mm
1 x	AX-60 starters (5 pcs)
1 x	10 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x	Red smoke bombs AX-60 (5 pcs)
1 x	White smoke bombs AX-60 (5 pcs)
1 x	Red smoke canister 140 g
1 x	76x23 Ø3.5 mm aluminium core wheel
1 x	Ring 320 mm length (5 pcs)
1 x	20 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	Red smoke canister 100 g
1 x	Tape GFK 38 mm
1 x	Single rim type C3 36/33,5/18,5 mm (pneumatics 55-70 mm)
1 x	SE Ring 300 mm (2 pcs)
1 x	Wheel 28 mm
1 x	Wheel FEMA 152 mm / 8 mm
1 x	13 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	SE Ring 450 mm (2 pcs)
1 x	PCARD Wireless System
1 x	Foil for sticking flaps and ailerons
1 x	4" - 102 x 45 mm Ø5 mm aluminium core wheel
1 x	Super Light Wheels(Sponge Tyre) Ø 50mm x 19mm (2pcs) axis Ø 3.5m
1 x	Blue smoke canister 140 g
1 x	127x43 Ø6.0 mm aluminium core wheel
1 x	Wheel FEMA 112 mm / 6 mm
1 x	"S" set for planes
1 x	Wheel FEMA 178 mm / 8 mm
1 x	Wheel 75 mm with electromagnet and brake disk (2 uds)
1 x	Yellow smoke canister 140 g
1 x	Super Light Wheels(Sponge Tyre) Ø 55mm x 19mm (2pcs) axis Ø 3.5m
1 x	SE Ring 400 mm (2 pcs)
1 x	Wheel 115 mm with electromagnet and brake disk + E-Brake (2 uds)
1 x	B4-0 rocket charges (6 pcs)
1 x	Blue smoke canister 100 g
1 x	60x25 mm tail wheel "type F3A"

2,275.83EUR