133.50EUR

Rainbow Autogyro
[MEGARAIN]



Aut. Rainbow con 4 palas

Aut. Rainbow con 4 palas

Aut. Rainbow con 4 palas

Aut. Rainbow con 3 palas

Aut. Rainbow con 3 palas

Aut. Rainbow con 3 palas
Autogyro was first built in 1923 by Spanish engineer Juan de la Cierva. Its development went on during thirties and in Second World War II was used in armies usually for observation purposes. In Czechoslovakia was then flown by Bata company.
Autogyro model RAINBOW is designed for model builders who has basic experiences with motor modelc comntrolled by elevator and rudder (or ailerons). No problems with starts form hand or grassy field. Landing si easy even with autogyro flying only with autorotation. Thanks to relatively big rotor diameter is flying very straightforward. In the air you can handle situations in which other models would be practically lost. Side movements of autogyro RAINBOW are made by rotor tilt. Elevator works well in the whole range of speeds and in autorotation mode allows almost vertical and very slow landing. For trasportation of autogyro it is possible to turn rotor blades back over the airframe (by slackening of two blade bolts)
Flying time varies from 10 to 20 minutes (battery 3xLion,1350mAh , motor MEGA RC 400/15/7, propeller APC10x5 E). You can use rechargeable batteries with both higher or lower capacity.
It is absolutely necessary to take off and land against the wind!

Available Options:

Combos:



temporarily out of stock
temporarily out of stock

Reviews

Customers who bought this product also purchased
3 blades set
3 blades set

temporarily out of stock
temporarily out of stock

We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x Pin type hinge Al 3,0x50 mm (2 pcs)
1 x Nylon hinge 15x0,3 (10 pcs)
1 x Fast'n EZ-CA-Hinge, lite (12 uds)
1 x Flap hinge 33x9 mm (6 pcs)
1 x 48 x 10 mm cylidric hinge Ø 3,0 mm (10 pcs)
2 x Pin type hinge Al 4,5x70 mm (2 pcs)
1 x Nylon hinge 20x15x0,3 (10 pcs)
1 x Gates hinge 30x16 mm (2 pcs)
1 x Pin hinge 26x11 mm (10 uds)
1 x Cylidric hinge 43 mm Ø 2,5 mm (5 pcs)
1 x Pin hinge 34x16 mm (10 uds)
1 x Cylidric hinge 33 mm Ø 2 mm (5 pcs)
1 x Indoor hinge with servo arm integraded
1 x 67 mm cylidric hinge Ø 4,5 mm (5 pcs)
1 x Medium pin type hinge (12 uds)
1 x Long pinned hinge (12 uds)
1 x Pin type hinge Al 3,0x50 mm demount (2 pcs)
2 x Long pinned hinge (6 uds)
1 x 33 x 8 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x Nylon hinge for flaps 33x9 (2 pcs)
1 x Nylon hinge 20x20x0,3 (10 pcs)
2 x 43 x 10 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x Gates hinge
1 x Micro flex hinge (12 uds)
1 x 48 mm cylidric hinge Ø 2,5 mm (5 pcs)
1 x 18 mm reinforced hinge
1 x Pin hinge 39x20 mm (10 uds)
2 x Gates hinge aluminium (1 pcs)
1 x Balsa panel 10x100x1000 mm
1 x BALSA trip 3.0x3.0x1000 mm
1 x BALSA leading edge 8x10x1000 mm
1 x A/C economy plywood 600x300x6+.0 mm
1 x Balsa panel 5.0x100x1000 mm
1 x BALSA trip 8.0x8.0x1000 mm
1 x BALSA triangular 8x8x1000 mm
1 x A/C quality beech plywood 600x300x0.6 mm
1 x BALSA trip 4.0x4.0x1000 mm
1 x Balsa panel 3.0x100x1000 mm
1 x A/C quality beech plywood 1520x750x4.0 mm
1 x Beech dowels 10 mm x 1000 mm
1 x A/C quality beech plywood 600x300x5.0 mm
1 x BALSA triangular 10x10x1000 mm
1 x A/C quality beech plywood 498x247x1.2 mm
1 x BALSA trip 5.0x5.0x1000 mm
1 x A/C quality beech plywood 600x300x8.0 mm
1 x BALSA trip 10x10x1000 mm
1 x A/C quality beech plywood 600x300x0.8 mm
1 x BALSA trip 3.0x5.0x1000 mm
1 x BALSA triangular 15x15x1000 mm
1 x A/C quality beech plywood BIRCH 600x300x1.0 mm
1 x Aluminium wide washer M4 Red (4 pcs)
1 x Anodized alum. M4x0,7x20 mm Flat Head screw (4 blue pcs)
1 x 2,4x1000 mm 2:1 green termoretract tube
1 x 4,8x1000 mm 2:1 black termoretract tube
1 x Tank + hopper Kevlar ASPIRE 4 L Kero / 1.5 L Smoke
1 x Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 100 m
1 x Boeing (TX) T-7A Camo
1 x 67 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs)
1 x Canopy hinges for Discus 2c, Discus 2a, Ventus 2cx (2pcs)
1 x Sun Cover ULTIMATUM 2.0 (Hispano Aviacion)
1 x Boomerang SPRINT V2 Red/Yellow
1 x Fast'n EZ-CA-Hinge (12 uds)
1 x Rotorhead pushrod
1 x Washer 2.2×4
1 x Blades 330mm
1 x Side Plate
1 x VIPER JET 2.2m + Electric landig Gear Deco: 01 Red-Blac-kWhit
1 x Balls 4 mm
1 x Grub screw M3x3 shouldered (2 pcs)
1 x Bearing housing
8,843.77EUR
Manufacturers
Manufacturer Info
Mega Motor
Mega Motor Homepage
Other products
Languages
Español English
Currencies