133.50EUR

Rainbow Autogyro
[MEGARAIN]



Aut. Rainbow con 4 palas

Aut. Rainbow con 4 palas

Aut. Rainbow con 4 palas

Aut. Rainbow con 3 palas

Aut. Rainbow con 3 palas

Aut. Rainbow con 3 palas
Autogyro was first built in 1923 by Spanish engineer Juan de la Cierva. Its development went on during thirties and in Second World War II was used in armies usually for observation purposes. In Czechoslovakia was then flown by Bata company.
Autogyro model RAINBOW is designed for model builders who has basic experiences with motor modelc comntrolled by elevator and rudder (or ailerons). No problems with starts form hand or grassy field. Landing si easy even with autogyro flying only with autorotation. Thanks to relatively big rotor diameter is flying very straightforward. In the air you can handle situations in which other models would be practically lost. Side movements of autogyro RAINBOW are made by rotor tilt. Elevator works well in the whole range of speeds and in autorotation mode allows almost vertical and very slow landing. For trasportation of autogyro it is possible to turn rotor blades back over the airframe (by slackening of two blade bolts)
Flying time varies from 10 to 20 minutes (battery 3xLion,1350mAh , motor MEGA RC 400/15/7, propeller APC10x5 E). You can use rechargeable batteries with both higher or lower capacity.
It is absolutely necessary to take off and land against the wind!

Available Options:

Combos:



temporarily out of stock
temporarily out of stock

Reviews

Customers who bought this product also purchased
3 blades set
3 blades set

temporarily out of stock
temporarily out of stock

We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
2 x BALSA trip 2.0x2.0x1000 mm
1 x Balsa panel 1.0x100x1000 mm
1 x BALSA trip 4.0x4.0x1000 mm
2 x Beech dowels 3.0 x 1000 mm
1 x A/C quality beech plywood 498x247x2.0 mm
1 x A/C quality beech plywood 498x247x1.2 mm
1 x Balsa panel 2.0x100x1000 mm
1 x Balsa panel 3.0x100x1000 mm
1 x Beech dowels 4.0 x 1000 mm
1 x A/C quality beech plywood 600x300x1.5 mm
1 x Balsa panel 2.5x100x1000 mm
2 x Beech dowels 2.0 x 1000 mm
2 x BALSA triangular 10x10x1000 mm
1 x A/C quality beech plywood BIRCH 600x300x1.0 mm
2 x Balsa panel 1.5x100x1000 mm
1 x Balsa panel 10x100x1000 mm
2 x BALSA trip 3.0x3.0x1000 mm
1 x ABS tube 8.0x6.0x1000 mm
1 x Steel tube (L 1000 mm Ø7 mm, Ø6,7 mm)
1 x Aluminium tube (L 1000 mm, Ø4.0 mm, Ø3.1 mm)
1 x Pine wood slat 6.0x6.0x1000 mm
1 x Pine wood slat 3.0x5.0x1000 mm
1 x Steel tube (L 1000 mm Ø6 mm, Ø5,7 mm)
1 x ABS tube 10.0x8.0x1000 mm
1 x Steel tube (L 1000 mm Ø3 mm, Ø2,7 mm)
1 x BALSA triangular 15x15x1000 mm
1 x ABS tube 18.0x16.0x1000 mm
1 x ABS tube 9.0x8.0x1000 mm
1 x Steel tube (L 1000 mm Ø9 mm, Ø8,7 mm)
1 x Thinwall Stainless Steel Tubing 28x0.6x1000 mm
1 x BALSA leading edge 8x10x1000 mm
1 x Steel tube (L 1000 mm Ø12 mm, Ø11,7 mm)
1 x Walnut wood slat 1.5x1.5x1000 mm
1 x Pine wood slat 2.0x10.0x1000 mm
1 x Mahogany wood slat 2.0x2.0x1000 mm
1 x Liston HAYA 8 x 8 x 1000 mm
2 x Pine wood slat 3.0x10.0x1000 mm
1 x 14x60 mm Mini rings Tie Wraps (4 pcs)
1 x Pad self adhesive, up to 3mm / 0.12″, (10 pcs)
1 x Foil for sticking flaps and ailerons
1 x Tape GFK 50 mm
1 x SE Ring 300 mm (2 pcs)
1 x SE Ring 330 mm (4 pcs)
1 x Z type of cable coupler Ø 1 (2 uds)
1 x Aluminium coupler M3/2 with ball bearing (1 pcs)
1 x Aluminium red ball links M3 V1 (10 pcs)
1 x Kwik link AL M2,5 L:23 mm (2 pcs) + Pin Ø 1,6 mm
1 x Aluminium blue ball links M3 V1 (10 pcs)
1 x Kwik link AL M3 con Clip (2 pcs)
1 x Aluminium coupler M2,5/2 with ball bearing (1 pcs)
1 x Threaded coupler M2,5 Ø 2 mm (10 pcs)
1 x Brass ball links BS M3 V1 (10 pcs)
1 x Clevis plastico I=45 mm / hole 3mm / pin 1 (2 pcs)
1 x Aluminium coupler M2/2 with ball bearing (1 pcs)
1 x Couple M4 for wire (10 pcs)
1 x Threaded coupler ALU M2 Ø 4 (2 uds)
1 x Clevis plastico I=44 mm / hole 3mm / pin 2 (2 pcs)
1 x Ball Link ALU M3 - RH (1 pcs)
1 x Clevis plastico I=26 mm / hole 2mm / pin 1 (2 pcs)
1 x Z type of cable coupler Ø 1.8 (2 uds)
1 x Threaded coupler ALU M3 Ø 4 (2 uds)
1 x Crimping sleeves for 1.1 mm cable (10 pcs)
1 x Threaded coupler ALU M2,5 Ø 3 (2 uds)
1 x Ball link duraluminium M3 V1 (10 pcs)
1 x Ball link Aluminio M3 x 3 x 5 x 18mm (6 uds)
1 x Z type of cable coupler Ø 2 (2 uds)
1 x Angled clevis with threaded rod M3
1 x Threaded coupler ALU M2,5 Ø 6 (2 uds)
1 x Ball link Aluminio M3 (2 pcs)
1 x Threaded coupler M2,5 Ø 3 mm (10 pcs)
1 x Flat washer 2.2 mm (20 pcs)
1 x 1/7 Pilot "Japanese"
1 x Carbon fiber rod 1.5 mm x 1000 mm
1 x 120x60 mm SLH KOVO wheel
1 x 1/12 Pilot "Cougar"
1 x Birch plywood plate 600x300x3.0 mm
1 x A/C quality beech plywood 600x300x5.0 mm
1 x Head spacer
1 x Head runner
441.06EUR
Manufacturers
Manufacturer Info
Mega Motor
Mega Motor Homepage
Other products
Languages
Español English
Currencies