Inicio » Catálogo » Zona Outlet » Accesorios »

59.00EUR 19.90EUR

Servo Controller Fibra optica

Servo controller based on fibre-optic transmission, allows to place e.g. throttle servo right next to the ignition without anxiety about disruptions “transfer” to the RC receiver.

Fibre-optic servo controller was designed as complement to the fibre-optic ignition cutoff. However, nothing stands on the way to exploit it independently.

The main task of controller is a possibility to place throttle servo close to the engine, so the throttle control link is short. Typically disadvantage of such installation is small servo distance and its wires from the engine ignition unit. Taking into account the adverse impact of electromagnetic noise caused by the ignition, which could get to the RC circuit, controller communicates with the receiver exclusively by fibre-optic which is resistant to electromagnetic disruptions. Thanks to that there is a minimum 30 cm distance between the ignition and the RC circuit in the model. In this case throttle servo is powered by the same package as the ignition unit.

Fibre-optic servo controller can be used also for other purposes than controlling the throttle. It will work everywhere where long wires are adversely affecting the electronics operation. With its help it is possible to control the servo move being in a significant distance or everywhere where a galvanic isolation of implementation servo elements from steering electronics is required.

FORCE Servo controller correctly works with voltage range from 3.6 V on the RC receiver side, and 3.6 V on the servo power supply side. Maximum allowed supply voltage on both sides is 16.0 V. It is necessary to remember not to exceed the allowed servo voltage, and if necessary to use appropriate voltage regulator.

FORCE Servo controller consists of the fibre-optic transmitter module plugged in the RC receiver and powered directly from it. Fibre-optic receiver module powered from the ignition battery. Fibre-optic wire*. For correct operation the device requires separate channel from the receiver (in most cases CH3).

Technical data:
Fiber Optic transmitter
– dimensions: 35mm x 11mm x 13mm
– receiver plug: Futaba, female 300mm
– power supply: 3,6V – 13,0V
* 2 – 3 x (LiPo/Li-Ion/LiFe)
* 4 – 9 x (NiMh/NiCd)
– weight: ~ 10,0 gram

Fiber Optic receiver
– dimensions: 47mm x 21mm x 13 mm
– battery plug: Futaba / JR male 150mm
– servo plug: Futaba / JR male 150mm
– power supply: 3,6V – 13,0V
* 2 – 3 x (LiPo/Li-Ion/LiFe)
* 4 – 9 x (NiMh/NiCd)
– weight: ~ 15,0 gram
– load capacity: constant 5 A, temporarily 30 A

pocas unidades

Comentarios

Búsqueda Rápida

Cesta de Compras

1 x	Motor DLE 170 M - Paramotores
1 x	Corona grade autoarranque DLE-170M
2 x	Corona pequeña autoarranque DLE-170M
2 x	Motor DLE 200cc Premium Muffler
2 x	Motor DLE 200cc Std
1 x	Carena ruedas de carbono Katana Mini (2 pcs)
1 x	Prisionero aluminio 5 mm Ø (4 uds)
2 x	Prisionero aluminio 4 mm Ø (4 uds)
1 x	Prisionero aluminio 2 mm Ø (4 uds)
2 x	Prisionero aluminio 6 mm Ø (4 uds)
1 x	Prisionero 2 mm Ø (4 uds)
2 x	Prisionero aluminio 3 mm Ø (4 uds)
1 x	Prisionero 4 mm Ø (4 uds)
1 x	Rótula M3 con tornillo y tuerca(6 uds)
1 x	Rótula V3 aluminio M2,5 5Diam (2 pcs)
1 x	Rótula INDUSTRIAL con bola M3 (2 uds)
1 x	Rótula M3 RPA's-UAV's
1 x	Rótula larga M1.6 con bola/base (6 uds)
1 x	Rótula con rodamiento M2 22x5,5
1 x	Rótula larga M2 con bola/tornillo (6 uds)
1 x	Rótula MAXI con bola/tornillo M3 (2 uds)
3 x	Rótula con bola M2 (10 pcs)
2 x	Rótula con bola M2,5 (10 pcs)
1 x	Rótula corta M2 con bola/tornillo (6 uds)
1 x	Bungee HLG Premium
1 x	Pasacable de goma Ø 6.4 mm (4 uds)
1 x	Prisionero aluminio 2.5 mm Ø (4 uds)
2 x	Plancha de balsa 1,5x100x1000 mm
2 x	Plancha contrachapado Abedul 600x300x0,8 mm
1 x	Plancha contrachapado Abedul 600x300x0,8 mm
1 x	Listón de BALSA 2,0x2,0x1000 mm
1 x	Listón de BALSA 5,0x5,0x1000 mm
2 x	Prisionero aluminio 3.5 mm Ø (4 uds)
1 x	Clips para fijar Ala (2 pcs)
1 x	Pasacable de goma 9.5 mm (4 uds)
1 x	Conjunto bieleta 140 mm para dirección
1 x	Cierre cabina tipo FOX MDM1 4m (1 par)
1 x	Plancha contrachapado Abedul 600x300x6,0 mm
1 x	Cierre cabina 33/23.5mm (2 uds)
1 x	Listón triangular de BALSA 8x8x1000 mm
1 x	Plancha contrachapado ABEDUL 600x300x1,0 mm
1 x	Pasacable de goma Ø 3.2 mm (4 uds)
1 x	Bateria arranque incl. compresor inflado
1 x	Ferrita 17x10x6.5 mm
1 x	Crimping sleeves para cables de 1.1 mm (10 pcs)
1 x	Ruedas ligeras 76 mm (2 pcs)
1 x	Piloto LUCAS ARTF
1 x	Extension silicona 30 cm hembra (Graupner)
1 x	Helice FALCON 32,5x11 PUSHER Carbono
1 x	Motor DLE 430 cc - Paramotores
2 x	Polo Hispano Aviación
1 x	Rótula corta M3 con bola/tornillo (6 uds)
1 x	Rótula con rodamiento M2,5 22x5,5
1 x	Rótula V3 aluminio M3/5 Diam con base corta (2 pcs)
1 x	Prisionero 5 mm Ø (4 uds)
1 x	Varilla mando doble roscada aluminio M3 90 mm (2 pcs) knurled
1 x	Rueda de cola de 28 mm
1 x	Pin largo M2 (10 uds)
1 x	Brazo direccional 16 mm Ø 3 mm
1 x	Liston de BALSA 8,0x8,0x1000 mm
1 x	Varilla mando doble roscada aluminio M3 40 mm (2 pcs)
1 x	Liston de BALSA 10 x 10 x 1000 mm
2 x	Protector punta ala 40x14 (2 pcs)
1 x	Plomo con adhesivo (2 pcs)
1 x	Varilla mando doble roscada aluminio M3 50 mm (2 pcs)
1 x	Varilla mando doble roscada duraluminio M3 130 mm (2 pcs)
2 x	Pasador 1.6x16 mm (10 uds)
1 x	Cierre para cabinas aluminio 5.4g
1 x	Varilla mando doble roscada duraluminio M3 40 mm (2 pcs)
1 x	Brazo direccional 16 mm Ø 4 mm
1 x	Varilla mando doble roscada aluminio M2,5 40 mm (2 pcs)
1 x	Listón de NOGAL 1,5x1,5x1000 mm
1 x	Varilla mando doble roscada duraluminio M3 60 mm (2 pcs)
1 x	Pin M1 (10 uds)
1 x	Listón de PINO 6,0x6,0x1000 mm
1 x	Combustible KAVAN CAR 25% 1 litro
1 x	IKURA GPS 4.28 m
1 x	Varilla mando doble roscada aluminio M3 90 mm (2 pcs)
1 x	Prisionero allen M4x6
1 x	Casquillo para grimpar cable de 0,85 mm (10 pcs)
1 x	Cierre para cabinas aluminio
1 x	Goma cierre cabinas Type H 2.5x0.5 (2m)
1 x	Listón de PINO 3,0x5,0x1000 mm
1 x	Listón de TILO 3,0x3,0x1000 mm
1 x	Listón triangular de BALSA 10x10x1000 mm
2 x	Mando control rueda delantera (MINI)
1 x	Brazo direccional 12 mm Ø 4 mm
1 x	Varilla mando doble roscada aluminio M2,5 60 mm (2 pcs)
1 x	Plancha contrachapado ABEDUL 600 x 300 x 2,0 mm
1 x	Listón de NOGAL 2,0x2,0x1000 mm
1 x	Cierre de plástico para cabinas
1 x	Manómetro de 4 mm
1 x	Tren retractil MINI neumático
1 x	Guardabarros ruedas 112/127 mm
1 x	Tren de cola (clase 60-120)
1 x	Brazo direccional 12 mm Ø 3 mm ( 2 uds)
1 x	Pasador M1,2x10 (10 pcs)
1 x	Rueda de cola para modelos de 8 a 12 kg
1 x	Listón de PINO 1,5x3,0x1000 mm
1 x	Válvula de doble acción PRO-HV
1 x	Cierre/Anclaje Ala M6 Rojo (2 pcs)
1 x	Listón de PINO 5,0x5,0x1000 mm
1 x	Anclaje cabina de soporte vertical "tipo F3A" (2 pcs)
2 x	Rueda de cola para modelos de 5 a 8 kg
1 x	Aero frenos eléctricos para veleros 250 mm (2 pcs)
1 x	Tren retráctil neumático tripata (Jet Legend)
1 x	Varilla mando doble roscada duraluminio M3 80 mm (2 pcs)
1 x	Sistema salvaservos rueda delantera BIDULE 55
1 x	Medidor de presión del aire
1 x	Desdoblador de mando 2mm (2 pcs)
1 x	Plancha contrachapado Abedul 600x300x1,5 mm
1 x	Pin para hélice plegable para eje 2 mm
1 x	Tren retráctil neumático tripata (Aero-Naut)
1 x	Listón de PINO 10x10x1000 mm
1 x	Varilla mando doble roscada aluminio M3 80 mm (2 pcs)
1 x	Aro pasacable Ø25 mm (4 pcs)
1 x	Bayoneta de carbono cuadrada 5x5x220 mm
1 x	Bisagra cilíndrica 43 mm Ø 2,5 mm (5 pcs)
1 x	Barra pegamento caliente Negro
1 x	Eje ruedas Ø 8 mm (2 uds)
1 x	Helice carbono 9x4.7 * 22x12
1 x	Cono NUT 1/4x28
1 x	Cono NUT M4
1 x	Cono NUT M6
1 x	Brazo servo 25 mm Futaba con rótula
1 x	Brazo servo 25 mm Hitec con rótula
1 x	Helice FIALA 15x8 3-Blade
1 x	Helice FIALA 23x8 Electric
1 x	Gorra Hispano Aviación
1 x	Plancha de goma espuma (310x210x3 mm)
1 x	Conector JAPAN G2 Set 5 pares
1 x	Plancha de balsa 6,0x100x1000 mm
2 x	Plancha contrachapado Abedul 600x300x1,5 mm
1 x	Plancha contrachapado Abedul 600x300x5,0 mm
1 x	Cierre/Anclaje Ala M3 Azul (2 pcs)
1 x	Actuador electrico 25 mm
1 x	Plancha contrachapado Abedul 600x300x0,6 mm
1 x	Plancha de balsa 10x100x1000 mm
1 x	Plancha contrachapado Abedul 600x300x6,0 mm
1 x	Albatros, cabina (Top Model)
1 x	Cono aluminio 34 mm / 4 mm helice plegable
1 x	Adaptador (GP/KO hasta 4S) para CellPRO 4S
1 x	Varilla mando doble roscada duraluminio M3 70 mm (2 pcs)
1 x	Cierre cabina V1 M3 Rojo (2 pcs)
1 x	Listón de CAOBA 3,0x3,0x1000 mm
1 x	Varilla mando doble roscada duraluminio M3 110 mm (2 pcs)
1 x	Varilla mando doble roscada duraluminio M3 50 mm (2 pcs)
1 x	Cono NUT M8x1,25
1 x	Cono Aluminio hélice fija 40 mm diámetro / eje 4,0 mm
1 x	Cono NUT M5
1 x	Cono Aluminio hélice fija 40 mm diámetro / eje 5,0 mm
1 x	Cono NUT M6
1 x	Cono Aluminio hélice fija 30 mm diámetro / eje 3,2 mm
1 x	Cono NUT M10x1
1 x	Cono NUT M5
1 x	Cono Aluminio hélice fija 40 mm diámetro / eje 3,0 mm
1 x	Cono Aluminio hélice fija 30 mm diámetro / eje 3,0 mm
1 x	Cono Aluminio hélice fija 40 mm diámetro / eje 3,2 mm
1 x	Brazo servo doble pull-pull 76/92 mm Futaba con rótulas
1 x	Terminales riostras M6x66 (2 uds)
1 x	Brazo servo 17 mm con rótula DES Graupner
1 x	Varilla latón hexagonal Ø 3.5 mm x 1000 mm
1 x	Helice Race 40 mm 1/4"(hélice derecha)
1 x	Plancha aluminio 500x250x0.5 mm
1 x	Muñeco Operario 1:32
1 x	Hélice RABOESCH M4 55 mm (5 Palas) (Hélice Izquierda)
1 x	Listón triangular de BALSA 15x15x1000 mm
1 x	Conjunto bieleta 90 mm y rótulas T. para dirección
1 x	Plancha de balsa 4,0x100x1000 mm
1 x	Plancha contrachapado Abedul 600x300x5,0 mm
1 x	Plancha contrachapado "Economy" 600x300x6,0 mm
1 x	Plancha de balsa 8,0x100x1000 mm
1 x	Plancha contrachapado Abedul 600x300x2,5 mm
1 x	Medidor de incidencias
1 x	Albatros rojo/blanco (Top Model)
1 x	Avia, cabina azul(Top Model)
1 x	Bidule 111 3000 mm
1 x	Cargador LiPo Charger4

24,697.89EUR

Fabricantes

Información del Fabricante


-	SETLO Página Principal
-	Otros productos

Notificaciones

Notifiqueme de cambios de Servo Controller Fibra optica

Comentarios

Escribir un comentario de este producto!

Idiomas

Monedas

Seguros