330.00EUR

ZENOAH ZG 26SLH Helicopter Engine
[TC2666]


Titan ZG 26SLH Helicopter Engine 26 ccm

New cylinder for considerably more power and efficient cooling.
Very thin piston ring for minimal friction and maximum power.
Magneto-electronic ignition with separate power coil and ignition coil, giving maximum power and smooth running.
Small Champion spark plug RZ7C with 10 mm thread.
Compact diecast crankcase.
Double counterbalanced crankshaft, very accurately aligned for the necessary concentric running, supported in three ballbearings. Needle roller bearings in conrod.
Walbro carburetor fitted with a priming pump to fill the carburetor for starting and a efficient airfilter intake silencer with integrated choke flap.
Robust pullcord starter

The new cylinder with the very thin high performance single piston ring is adapted from the extremely high power G230RC car engine for helicopter use. This new cylinder has four retaining screws as apposed to two for the G230RC cylinder. The extremely wide cooling fins are invaluable for helicopter use.
Other components are also optimized for helicopters, for example the crankshaft is very accurately aligned for the necessary concentric running. There is a very robust pullcord starter as well as very efficient airfilter intake silencer fitted to this engine. The carburettor is fitted with small priming pump to fill the carburettor for starting.
The Walbro carburettor is extremely reliable, is designed for the higher rpm involved, the completely dependable magneto ignition without contact breaker, the clean running due to low dilution full synthetic oil resulting in the absence of the smelly smoke trail, the availability of the fuel at every filling station with it?s very low price. These are some of the arguments resulting in the popularity of first the ZG 22 and then the ZG 23SLH, are now exactly relevant to the ZG 26SLH.

Specifications:
Capacity: 25,4 ccm
Bore: 34 mm
Stroke: 28 mm
Compression ratio: 8.8 eff.
Power: 2.2 hp/1.62 kW
Torque: 1,48 Nm
Power with tuned pipe: >3.0 hp/>2.2 kW
Weight: 1580 g without muffler
Fuel: 1:40 BEL RAY H1-R / Petrol


Reviews
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x USBCOM 5i
1 x CC 11 Conector
1 x HBC 10035-3 32-Bit
1 x FALCON 20X9 CARBON PROPELLER (GAS)
1 x DUPLEX 2.4EX Central Box 210
1 x Propeller POWER-PROP 13x9
1 x Straightened rod Ø 14.0 mm x 1000 mm
1 x Propeller POWER-PROP 14x9
1 x Propeller POWER-PROP 13x9 Izda
1 x Carbon plate 350x150x1.0 mm
1 x Piston EME 35cc
1 x Diaphragm Set Walbro 116/152cc
1 x EME ignition free wheel
1 x Piñon motor autostarter 35cc
1 x Collector screw DA
1 x Carb Carrier, red DA-85, DA-100L and DA-120
1 x Motor NGH GT-17
2 x Propeller hub EME 60cc
1 x PCI-HV ignition conversion set with Zenoah rubber plug cap for Z
1 x Cylinder head, left for VM 170/210
1 x Cylinder-piston Assembly 30cc
1 x Carburetor diaphragm set DA-150/170
1 x Exhaust gasket DA-60/120
1 x Carburador DA-35, DA-50R-DA-100L , VM-60/70
1 x Crankcase gasket DA 170
1 x Rear cover O-ring 26/30 cc
1 x DA-50R motor alumine support
1 x Flex-headers for Valach VM 85B2-FS
2 x Motor EME 35 cc with electric starter
1 x Pick up EME 55/60 cc
1 x Stainless steel flange for VM 60/70/120/140
1 x A/C quality beech plywood 600x300x6.0 mm
1 x Sandwich carbon + poplar 3mm + carbon 480x290 mm
1 x ESC MEZON 115 Opto
1 x Waterproof adhesive tape, width 19mm, length 25m
1 x L ELBOW 90º ø 25 mm
1 x CDI EME 55/60 cc
1 x Power supply NT 40 Amp.
1 x Motor EME 35 cc
1 x 
1 x L ELBOW DA-150 "normal" (2 pcs)
1 x Gasket, from reed valve carrier to carb carrier DA-150L/170
1 x Gasket carburetor carrier->crankcase DA-85 DA-100L DA-120 DA-200
1 x Ignition unit for DA-70/100/120/150/170/200
1 x 10 mm dogdrive props
1 x Pick up DA50/100/150
1 x BATTWIN BATTERY REDUNDANCY SYSTEM
1 x Power supply NT 25 Amp.
1 x HITEC Power Supply 30A. Max. 540w
4,562.48EUR
Manufacturers
Manufacturer Info
Toni Clark
Toni Clark Homepage
Other products
Languages
Español English
Currencies