Top » Catalog » Acces. for Motors » Fuel/Smoke Pumps » POWER8015

186.00EUR

PowerBox Smokepump JETs 2x outside
[POWER8015]

Product description

The PowerBox Smokepump has been developed by PowerBox-Systems specifically for pumping smoke oil in model aircraft. The mechanical system and electronics are manufactured on our own premises, and the unit's high standard of quality is evident from its long effective life: the PowerBox Smokepump is the world's most durable smoke oil pump, as has been demonstrated in several long-term tests.

The mechanical pump system is assembled entirely from high-quality aluminium and brass parts. All our pumps are subjected to a running-in procedure during manufacture, ensuring that the gears mesh perfectly, and that the pump is 100% leak-free. Tight manufacturing tolerances eliminate the need for a separate cut-off valve with the PowerBox Smokepump.

The electronic circuit is infinitely variable within the range 0%-100%, allowing the pilot to fine-tune the flow rate to match the exact requirements of the model. The Smokepump can be powered either by a PowerBox or a separate battery.

If a separate battery is used, the electronic circuit switches to a "stand-by" mode if the receiver fails to pick up a signal. This means that it is not necessary to provide a separate switch to isolate the PowerBox Smokepump from the battery when you switch the model off.

The PowerBox Smokepump is available in a Standard version and a Jet version, the later with higher throughput and twin outlets.

The maximum flow rate of the Smokepump (Order No. 8010) is around 750 ml./min., while the Smokepump Jet (Order No. 8015) is capable of around 950 ml. The set includes all the necessary connecting leads and a length of heat-resistant hose. The standard set also contains a Y-piece which can be used to connect both silencers of an opposed-twin (boxer) engine.

Features
Durable metal-geared pump
Infinitely variable flow rate from 0-100%
No external cut-off valve required
High maximum flow rate
Can be operated directly from the receiver power supply
Stand-by cut-off when used with separate battery
Compact design
Low current drain
Mounting facility

Technical Data
Operating voltage 4.0V - 9.0V
Current drain Power-on state approx. 1.8 Ampere at 100%
Current drain Standby 10µA
Max. flow rate max. 950ml/min
Smoke medium Smokeöl „blue Max“ or 3W Smokeöl
Dimensions 79 x 31 mm
Weight 128g
Temperature range -30°C to +75°C

under request

Reviews

Quick Find

Shopping Cart

2 x	Beech dowels 4.0 x 1000 mm
1 x	Birch plywood plate 600x300x3.0 mm
1 x	Balsa panel 6.0x100x1000 mm
2 x	BALSA triangular 15x15x1000 mm
1 x	Balsa panel 2.5x100x1000 mm
1 x	quality beech plywood BIRCH 600x300x2.0 mm
1 x	A/C quality beech plywood 600x300x5.0 mm
1 x	BALSA trip 2.0x2.0x1000 mm
1 x	Balsa panel 3.0x100x1000 mm
1 x	Birch plywood plate 600x300x4.0 mm
1 x	BALSA trip 5.0x5.0x1000 mm
1 x	A/C quality beech plywood 600x300x0.6 mm
1 x	Beech dowels 3.0 x 1000 mm
1 x	A/C quality beech plywood 600x300x0.8 mm
1 x	Balsa panel 10x100x1000 mm
1 x	BALSA trip 4.0x4.0x1000 mm
1 x	A/C quality beech plywood BIRCH 600x300x1.0 mm
1 x	Balsa panel 4.0x100x1000 mm
1 x	Beech dowels 2.0 x 1000 mm
1 x	Balsa panel 2.0x100x1000 mm
2 x	Black copper lacquer wire Ø0,2 mm (5 m)
2 x	4 LiPo XH>EH adapter
1 x	Adapter lead MPX/EC3
1 x	Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH
1 x	Cable set PREMIUM, SUB-Done 4three fuselage/wing 160 cm
4 x	CC 05
1 x	Double conector with JR adapter and 200 mm extension
1 x	Cabel charger battery transmiter Futaba 2x0,5 qmm (50 cm)
2 x	Copper lacquer wire Ø0,2 mm (5 m)
1 x	Bec MR UBEC 5A (5v/6v/7v)
1 x	3 LiPo XH>EH adapter
1 x	Balanceradapter JST-XH (Heli 47G) 2-6 c.
2 x	DPSI Ampere battery backer
2 x	CellPRO 4S Adaptader (GP/KO up to 4S)
2 x	DPS Switch JR/JR
2 x	Balance "Y" Wire 7S, 2x JST-XH / 1x JST-EH
2 x	Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm)
1 x	BEC 3A FOXY
1 x	Circlick securite
1 x	Foil for sticking flaps and ailerons
1 x	RUDDOG Protection and Heat Shield Tape (2mx50mm)
1 x
3 x	SE Ring 330 mm (4 pcs)
1 x	20x1000 mm Ring Strap Back To Back
1 x	5 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x	20x200 mm battery rings
2 x	10 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x	Tape GFK 38 mm
2 x	SE Ring 360 mm (2 pcs)
1 x	SE Ring 480 mm (2 pcs)
1 x	SE Ring 450 mm (2 pcs)
1 x	Spikes Band (5 m)
2 x	SE Ring 350 mm (2 pcs)
1 x	SE Ring 400 mm (2 pcs)
1 x	14x60 mm Mini rings Tie Wraps (4 pcs)
1 x	13 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x	76 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs)
1 x	Cylidric hinge 33 mm Ø 2 mm (5 pcs)
1 x	Pin type hinge Al 3,0x50 mm (2 pcs)
1 x	Long pinned hinge (6 uds)
2 x	43 x 10 mm cylidric hinge Ø 2,5 mm (10 pcs)
2 x	Fast'n EZ-CA-Hinge (12 uds)
1 x	67 mm cylidric hinge Ø 5 mm (4 pcs)
1 x	Large flex hinge (12 uds)
1 x	Motor DLE 170 M- Paramotors
1 x	Pine wood slat 2.0x2.0x1000 mm
1 x	Ballast 700gr OPALE
1 x	Straightened rod Ø 2.5 mm x 1000 mm
1 x	Buy Perforated film 100 cm / 50 m
1 x	Breatex™ Non-woven absorber 300 g/m² Roll 41 m
1 x	Air pressure gauge
1 x	Skies 2x 335 mm + 1x Esqui 250mm
1 x	UBEC 6A KAVAN
1 x	Female prolonguer XH 30 cm 6 cell cable of silicone 0,25 mm
1 x	Exhaust elbow for SAITO FA65/72/80/82a/91S/100/
1 x	Male Prolonger TP 4/5S
1 x	SBEC 30 D
1 x	Connector Sub-D 2+5 Male
2 x	PowerBox Smokepump
2 x	Red copper lacquer wire Ø0,2 mm (5 m)
1 x	Electric Fuel Pump 12v
1 x	Cabling for Fox MDM1 wings
3 x	30 cm BEC cable (male)
1 x	PSC 6
1 x	Interruptor RX/Batterie
1 x	Pins M connect Multipin connectors AWG 20-24
1 x	Servo slow down unit (0,7-14,7 sec )
1 x	EXTREME FLIGHT BLUE MAGNETIC ROUND FILLER PLUG
1 x	550 cc gasoline fuel tank complet
1 x	Deposito DUBRO 3000cc-100oz
1 x	22m Fitting barb
1 x	Extra hard 1500 ccm complete gasoline fuel tank
1 x	1/4 x 1/8" VITON tube for gas, kerosene, smoke (30 cm)
1 x	EXTREME FLIGHT BLACK MAGNETIC ROUND FILLER PLUG
1 x	Deposito SECRAFT V2 1000 ml Gas
1 x	Balance "Y" Wire 6S, 2x JST-XH / 1x JST-EH
1 x	280 cc gasoline fuel tank complet
1 x	SE Ring 300 mm (2 pcs)
1 x	Tape GFK 25 mm
2 x	Connector Sub-D 2+5 Female
1 x	Pad Screw Mount M3, up to 3mm / 0.12″, (10 pcs)
1 x	26 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	Ring 320 mm length (5 pcs)
1 x	18 mm reinforced hinge
1 x	Gates hinge
1 x	25 mm reinforced hinge
1 x	Gates hinge aluminium (1 pcs)
1 x	Gates hinge black 30x16 mm (2 pcs)
1 x	Cylidric hinge 43 mm Ø 2,5 mm (5 pcs)
1 x	Pin type hinge Al 4,5x70 mm (2 pcs)
1 x	3,9 mm ZG20-ZG38 servo arm
1 x	Servo MKS 6100 DS
1 x	Servo MKS HBL599 SL
1 x	Micro flex hinge (12 uds)
2 x	CC 01
1 x	Servo MKS HV747
1 x	Brazo servo MKS X8 Metal L:1.25/1.5 inc
1 x	48 mm cylidric hinge Ø 2,5 mm (5 pcs)
1 x	Servo KST X10 V2.0 ala 10mm 28g 10.8Kg
1 x	Servo KST X10 MINI wing 10mm 23g 7.5Kg
1 x	Wheel Ø 90 mm (1 ud) Electron Retracts
1 x	Wheel 28 mm
1 x	4" - 102 x 45 mm Ø5 mm aluminium core wheel
1 x	20 mm tail wheel for 0,5-1 Kg models
1 x	Wheel 22 mm
1 x	Wheel FEMA 165 mm / 8 mm
1 x	Foam wheel Ø 38 mm (2 pcs)
1 x	Wheel FEMA 112 mm / 6 mm
1 x	152x46 Ø6.0 mm aluminium core wheel
1 x	Wheel 75 mm with electromagnet and brake disk (2 uds)
1 x	Wheel FEMA 140 mm / 6 mm
1 x	Wheel FEMA 152 mm / 8 mm
1 x	Anodized aluminium servo M3x16 screw (4 red pcs)
1 x	OBECHI sheet 2.0x3.0x1000 mm
1 x	Walnut wood slat 1.5x1.5x1000 mm
1 x	Mahogany wood slat 2.0x2.0x1000 mm
1 x	Linden wood slat 3.0x3.0x1000 mm
1 x	Servo KST BLS915 HV V8.0 25Kg 20mm 78g
1 x	Servo KST X20 8.4-50 V8.0 45kg 8.4v Softstar
1 x	Servo KST A15-1810 20kg/cm@8.4V / Coreless Motor
1 x	SBEC Jeti
1 x	USB Interface REVOLECTRIX for CellPRO 10s
1 x	JETImodel Addcap 1640
1 x	XICOY X45 rail
1 x	Magnetic Interruptor MULTIPLEX
1 x	SPS 70V 100/200 A
2 x	wing/fuselage connector for 12 pines AWG 20-24
1 x	Selfstart electronic switch
1 x	Tank ULTIMATUM 2.0 (3.2 L) PRO
1 x	Electric Landing Gear GS-200 ULTIMATUM 2.0 (Elektron Retracts)
1 x	Quick hose connector 6-4 mm
1 x	Big-Malibu XL Roof box with surfboard rack GREY
2 x	5 LiPo XH>EH adapter
1 x	PWC6 PowerWingConnector for 6 servos with fuselage socket
1 x	OPUS-V / Jet-CC-BF
1 x	Smoke pump RCEXL
1 x	Interruptor SAFET-SWITCH 12HV Twinbatt
1 x	SBEC 40
1 x	Male connector for 20 pines AWG
1 x	Tank GFK Opus/JEt 300 ml
1 x	Wings Bags JEEMO
1 x	JEEMO Kit ARF Basic (2 color Carbon finish) XTRALIGHT
1 x	JEEMO Kit ARF Basic (2 color) - XTRALIGHT
1 x	30 cm BEC cable (female)
2 x	wing/fuselage connector for 16 pines AWG 20-24
1 x	SPARK Switch 12v
1 x	"Y" charging 4mm wire (2 IN-1 OUT).
1 x	Female connector for 20 pines AWG
1 x	Electric Fuel pump
1 x	Interruptor SPS 70v 60/120A
1 x	SPS Remote switch actuator
1 x	Male connector for 16 pines AWG
1 x	DPSI magnetic switch actuator (housing)
1 x	Variable Flow Smoke Pump System
1 x	Secraft Fuel system v2, red color
1 x	Battery charging cable XT60
1 x	MAX BEC 2
1 x	JETImodel SINGLE BEC
1 x	Adapter lead MPX/XT60

13,913.42EUR