Top » Catalog » Acces. for Motors » Starters/CDi » SETOKW

16.00EUR

Opto Gas Engine Kill Switch
[SETOKW]

This kill switch is double Optically Coupled to isolate your ignition system from your radio system (No Interference!!). It also consist an additional safety functions.

Device features
• Includes a remote mountable ultra bright LED to indicate when the ignition is armed or not, or if the safety sequence protection is active.
• The LED diode informs also if Fail-Safe occured during flight (even after landing).
• Safety sequence protection for engine ignition powering up after model preparation.
• Double optically Coupled input/output is Isolated.
• Turning engine ignition ON or OFF directly from RC Transmitter
• No need to use additional mechanical switch for disconnecting ignition battery.
• 8 Bit microcontroller powered directly from RC receiver.
• 3,0 - 24,0 Volt Li-Po/Li-Ion/A123/Ni-Mh/NiCad Input (receiver side).
• 3,0 - 20,0 Volt Li-Po/Li-Ion/A123/Ni-Mh/NiCad MOSFET Output (ignition side).
• Possible to use one battery setup (independent two batteries setup by default).
• Max. current output: 5 Amp continous, 16 Amp peak
• Fail-Safe engine kill when interference or signal lose is longer then 1 second. (this function can be turned OFF).
• PPM-PCM 2048 – 1024 & 2.4Ghz Interface Support.
• Low Voltage Drop – Less than 150mv.
• 100% Surface Mount Technology.
• Heavy Gauge Wires 22AWG, universal connectors Futaba/JR.
• Small and light weight – only 15 Grams!

This device plugs into a spare receiver channel.

This is a must have safety device for any gas powered plane! This device allows you to safely kill your engine at anytime (on the ground, or inthe air!)

temporarily out of stock

Reviews

Customers who bought this product also purchased

Spark motor OS nº 3

temporarily out of stock

Quick Find

Shopping Cart

1 x	Recess mount-rem. glow plug set
2 x	RCEXL Electronic ignition twin A-02
3 x	Compact on-board starting system (9715)
2 x	DLE 30 complete electronic ignition
3 x	Aluminium ignition bad (blue)
2 x	Starter EM Gear Power 250
1 x	GLOW 9C + accesories
1 x	Compact on-board starting system (9512)
1 x	Opto Gas Engine Kill Switch
3 x	RCEXL Electronic ignition twin CM-6
1 x	Excentric gearbox for 3,2mm axis (4,1:1)
1 x	Excentric gearbox for 2,3mm axis (4,1:1)
1 x	STD excentric gearbox for 2,0mm axis (4,5:1)
2 x	Planetary gearbox(3,33:1)
1 x	STD excentric gearbox for 2,3mm axis (4,1:1)
1 x	Excentric gearbox for 2,0mm axis (4,5:1)
2 x	STD excentric gearbox for 2,0mm axis (5,0:1)
1 x	STD excentric gearbox for 2,0mm axis (3,75:1)
1 x	STD excentric gearbox for 2,3mm axis (3,5:1)
1 x	Planetary gearbox(3,8:1)
2 x	Excentric gearbox BB for motor 600, 3,2mm axis (2,8:1)
1 x	STD gearbox for Speed 480 3,2mm axis (2,33:1)
2 x	Excentric gearbox for 2,0mm axis (4,1:1)
3 x	Planetary gearbox(3,8:1)
1 x	Excentric gearbox BB for motor 600, 3,2mm axis (1,75:1)
1 x	STD excentric gearbox for 2,0mm axis (4,5:1)
1 x	STD excentric gearbox for 2,0mm axis (4,1:1)
2 x	Planetary gearbox(3,8:1)
2 x	Excentric gearbox for 2,3mm axis (2,33:1)
1 x	Excentric gearbox for 2,0mm axis (3,75:1)
1 x	Set cintas unión paracaídas 145 cm
1 x	Compact on-board starting system (9525)
1 x	Cable servo PREMIUM 1 m (blanco/rojo/negro) AWG21 + AWG26 TPE
1 x	SE Ring 400 mm (2 pcs)
1 x	STD excentric gearbox for 3,2mm axis (3,0:1)
1 x	Field folding model stand SebArt
1 x	STD excentric gearbox for 2,3mm axis (2,33:1)
1 x	Crimping tool
1 x	White silicone 0,25 qmm wire (150 m)
1 x	Silicone red 0,25 mm² wire (25 m)
1 x	Hexagonal ball head 2.0 x 50 mm
1 x	Black silicone 0,25 mm² wire (25 m)
1 x	Truck-trailer for gliders 720 x 239 mm
1 x	Electromotor starter EME 35cc
1 x	Spikes Band (5 m)
1 x	SE Ring 330 mm (4 pcs)
1 x	Excentric gearbox for 2,0mm axis (5,0:1)
1 x	200m servo "Premium" wire (white/red/blue)
1 x	Planetary gearbox(3,33:1)
1 x	Pad self adhesive, up to 3mm / 0.12″, (10 pcs)
1 x	Silicone 0,25 qmm servos wire Graupner (5 m)
1 x	Hot Glue Stick BLACK
1 x	BALSA triangular 15x15x1000 mm
1 x	Gates hinge aluminium (1 pcs)
1 x	48 mm cylidric hinge Ø 2,5 mm (5 pcs)
1 x	ABS tube 18.0x16.0x1000 mm
1 x	Blind nut M4 (10 pcs)
1 x	DPSI magnetic switch actuator (housing)
1 x	Tube Pitot to PIXHAWK
1 x	Carbon tube (L 1000 mm, Ø12 mm, Ø10 mm)
1 x	Aluminium cap bolt washer M3 black (8 pcs)
1 x	Excentric gearbox for 3,2mm axis (3,0:1)
1 x	CellPRO 4S Adaptader (GP/KO up to 4S)
1 x	STD excentric gearbox for 3,2mm axis (3,5:1)
1 x	Copper lacquer wire Ø0,2 mm (5 m)
1 x	Blind nut M4 (4 pcs)
1 x	Nylon hinge 15x0,3 (10 pcs)
1 x	ABS tube 2.0x1.0x1000 mm
1 x	Digital Air Speed Sensor And Pitot Tube Set
1 x	Pin hinge 39x20 mm (10 uds)
1 x	Balsa panel 2.5x100x1000 mm
1 x	Clip fixing for wing (2 pcs)
1 x	Connectors banana oro 6,0 mm Ultralight (M/F)
1 x	Excentric gearbox for 3,2mm axis (2,33:1)
1 x	ABS tube 3.0x1.0x1000 mm
1 x	Blind nut M6 (4 pcs)
1 x	Cabel charger transmitter GRAUPNER
1 x	Medium pin type hinge (12 uds)
1 x	Large flex hinge (12 uds)
1 x	Aluminun wheel collar 2 mm Ø (4 uds)
1 x	15 mm reinforced hinge
1 x	Dean "T" - Futaba Adapter
2 x	Aluminium wide washer M4 Red (4 pcs)
1 x	Aluminium cap bolt washer M3 red (8 pcs)
1 x	45 mm rods + T patellas set for direction control
1 x	ABS tube 5.0x4.0x156 mm
1 x	Aluminium wide washer M3 red (4 pcs)
1 x	Aluminium tube (L 1000 mm, Ø3.0 mm, Ø2.1 mm)
1 x	Cylidric hinge 33 mm Ø 2 mm (5 pcs)
1 x	80 mm rods set for direction control
1 x	A/C quality beech plywood 1520x750x3.0 mm
1 x	ABS tube 12.0x10.0x1000 mm
1 x	Ferrita 17x10x6.5 mm
1 x	11 mm Rubber pads (14 pcs)
1 x	A/C economy plywood 600x300x6+.0 mm
1 x	A/C quality beech plywood 600x300x8.0 mm
1 x	STD excentric gearbox for 2,0mm axis (3,5:1)
1 x	DPSI Ampere battery backer
1 x	Micro flex hinge (12 uds)
1 x	Carbon tube (L 1000 mm, Ø16 mm, Ø14 mm)
1 x	Anodized aluminium servo M4x5/8 screw (4 lilac pcs)
1 x	Conector JAPAN G2 Set 5 pares
1 x	Excentric gearbox for 2,0mm axis (5,0:1)
1 x	ABS tube 3.0x2.0x1000 mm
1 x	Aluminium cap bolt washer M4 red (8 pcs)
1 x	Balance "Y" Wire 6S, 2x JST-XH / 1x JST-EH
1 x	BALSA trip 3.0x3.0x1000 mm
1 x	Ferrita 14x8x5.5 mm
1 x	30 cm BEC cable (male)
1 x	Planetary gearbox(3,33:1)
1 x	67 mm cylidric hinge Ø 4,5 mm (5 pcs)
1 x	Carbon tube (L 1000 mm, Ø18 mm, Ø15 mm)
1 x	Cable grommet Ø 5 mm (4 uds)
1 x	Balanceradapter JST-XH (Heli 47G) 2-6 c.
1 x	5 LiPo XH>EH adapter
1 x	DPS Switch JR/JR
1 x	Aluminium M2x12 mm screw (4 pcs)
1 x	Conector AS150 7mm antichispazo (Set: 2 pares)
1 x	Bec MR UBEC 5A (5v/6v/7v)
1 x	Aluminium wide washer M3 gold (4 pcs)
1 x	12 mm floating pad (49 pcs)
1 x	Allen wheel collar M3x5
1 x	Connector CAN 15
1 x	Blind nut M2 (10 pcs)
1 x	Conector JR Servo female (10 pcs)
1 x	Adapter lead MPX/XT60
1 x	Blind nut M3 (4 pcs)
1 x	250 mm / 16 mm Airbrakes
1 x	2.3 mm Adapter for 30 mm spinners
1 x	2,3 mm Prop Adapter M6
1 x	29,0 mm propeller (rigth propeller)
1 x	29,0 mm propeller (left propeller)
1 x	3.2 mm Prop Adapter M6
1 x	"L" servo arm 65x49 mm (2 pcs)
1 x	3 mm Leader (L 100 mm)
1 x	3 mm Prop Adapter M6
1 x	25,0 mm 3-BL M4 hydro-propeller (rigth hydropropeller)
1 x	28 mm turnbuckle
1 x	14 mm Portholes for screws (10 pcs)
1 x	15x7 tree blades propeller LEFT
1 x	25 mm fenders (10 pcs)
1 x	25,0 mm 3-BL M4 hydro-propeller (left hydropropeller)
1 x	3 mm Prop Adapter M6
1 x	290 mm M4/4 mm Prop shaft
1 x	3,2 mm Prop Adapter M6
1 x	11x7 tree blades propeller
1 x	15x7 tree blades propeller
1 x	12 mm mast holder
1 x	3.2 mm Prop Adapter M8
1 x	12x8 tree blades propeller
1 x	3,2 mm Prop Adapter M8
1 x	31,0 mm propeller (rigth propeller)
1 x	12 mm portholes (10 pcs)
1 x	3.17 mm Prop Adapter CN-Spinner
1 x	14 mm portholes (10 pcs)
1 x	33 x 8 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x	Extension MPX-MPX 20 cm
1 x	aluminium servo arm V2-JR 2,0 inch M3
1 x	Crystal Universal RX 35.140 Ch 74
1 x	Connectors banna oro 2 mm (M/F)
1 x	30 mm gas motor standoff
1 x	45 mm gas motor standoff
1 x	15 mm floating pad (30 pcs)
1 x	6 mm Quick clamp_S (10 pcs)
1 x	Crystal Universal RX 35.120 Ch 72

4,841.28EUR