Top » Catalog » Acces. for Motors » Starters/CDi » SETOKW

16.00EUR

Opto Gas Engine Kill Switch
[SETOKW]

This kill switch is double Optically Coupled to isolate your ignition system from your radio system (No Interference!!). It also consist an additional safety functions.

Device features
• Includes a remote mountable ultra bright LED to indicate when the ignition is armed or not, or if the safety sequence protection is active.
• The LED diode informs also if Fail-Safe occured during flight (even after landing).
• Safety sequence protection for engine ignition powering up after model preparation.
• Double optically Coupled input/output is Isolated.
• Turning engine ignition ON or OFF directly from RC Transmitter
• No need to use additional mechanical switch for disconnecting ignition battery.
• 8 Bit microcontroller powered directly from RC receiver.
• 3,0 - 24,0 Volt Li-Po/Li-Ion/A123/Ni-Mh/NiCad Input (receiver side).
• 3,0 - 20,0 Volt Li-Po/Li-Ion/A123/Ni-Mh/NiCad MOSFET Output (ignition side).
• Possible to use one battery setup (independent two batteries setup by default).
• Max. current output: 5 Amp continous, 16 Amp peak
• Fail-Safe engine kill when interference or signal lose is longer then 1 second. (this function can be turned OFF).
• PPM-PCM 2048 – 1024 & 2.4Ghz Interface Support.
• Low Voltage Drop – Less than 150mv.
• 100% Surface Mount Technology.
• Heavy Gauge Wires 22AWG, universal connectors Futaba/JR.
• Small and light weight – only 15 Grams!

This device plugs into a spare receiver channel.

This is a must have safety device for any gas powered plane! This device allows you to safely kill your engine at anytime (on the ground, or inthe air!)

temporarily out of stock

Reviews

Customers who bought this product also purchased

Spark motor OS nº 3

temporarily out of stock

Quick Find

Shopping Cart

2 x	40,0 mm hydro-propeller (left hydropropeller)
2 x	Servo HBS 690BB HV Digital
1 x	Hard brass tubing (L 1000 mm, Ø18.0 mm, Ø16.0 mm)
1 x	SERVO DES 707 BB MG
1 x	Soporte metal para servos
2 x	Carbon tube (L 1000 mm, Ø4 mm, Ø2,5 mm)
1 x	Straightened rod Ø 6.0 mm x 1000 mm
1 x	Hard brass tubing (L 1000 mm, Ø14.0 mm, Ø12.0 mm)
2 x	Carbon tube (L 1000 mm, Ø16 mm, Ø12 mm)
1 x	Switching module high voltage SXH
1 x	Carbon fiber rod 5.0 mmx1000 mm
2 x	Brass hexagonal rod Ø 3 mm x 1000 mm
1 x	Ring 320 mm length (5 pcs)
1 x	Hard brass tubing (L 1000 mm, Ø6.0 mm, Ø5.2 mm)
1 x	Hard brass tubing (L 1000 mm, Ø13.0 mm, Ø12.0 mm)
3 x	Brass rod Ø 0.5 mm x 1000 mm
1 x	Hard brass tubing (L 1000 mm, Ø11.0 mm, Ø10.0 mm)
1 x	Carbon fiber rod 0.5 mmx1000 mm
1 x	Straightened rod Ø 5.5 mm x 1000 mm
3 x	28 mm tailwheel unit
3 x	Bearing block for noseleg landing gear
3 x	Brass hexagonal rod Ø 5 mm x 1000 mm
2 x	Decorative caps, multicoloured
2 x	Beech dowels 3.0 x 1000 mm
2 x	Balanceradapter JST-XH (Heli 47G) 2-6 c.
3 x	Decorative caps, multicoloured, short
1 x	Brass rod Ø 0.8 mm x 1000 mm
1 x	Brass rod Ø 1.0 mm x 1000 mm
1 x	Flap hinge (6 pcs)
1 x	Coupling bush 5 - 5 mm
1 x	Adjustable brass horn threaded M3
2 x	Beech dowels 2.0 x 1000 mm
1 x	Brass hexagonal rod Ø 3.5 mm x 1000 mm
1 x	Aluminium tube (L 1000 mm, Ø4.0 mm, Ø3.1 mm)
1 x	Aluminium sheet 500x250x0,5mm
3 x	Brass hexagonal rod Ø 4 mm x 1000 mm
3 x	Canopy Latch
2 x	Hard brass tubing (L 1000 mm, Ø10.0 mm, Ø9.1 mm)
1 x	Transmitter GRAUPNER MZ-24 Pro
1 x	Steel tube (L 1000 mm Ø3 mm, Ø2,7 mm)
1 x	XH female balance (4S) connector (2 pcs)
1 x	Aluminium alloy coupler for carbon tube 6/M4
1 x	Canopy Lock V1 M3 Blue (2 pcs)
1 x	Horn with ball 55x40
1 x	Conector BEC male (10 pcs)
1 x	Aluminium rod Ø 4.0 mm x 3000 mm
1 x	Conector AS150 7mm antichispazo (Set: 2 pares)
1 x	UHU hart 35 g
1 x	Glases Flitemaster
1 x	Aluminium tube (L 1000 mm, Ø7.0 mm, Ø6.1 mm)
1 x	Straightened rod Ø 7.0 mm x 1000 mm
1 x	Connectors banna oro 2 mm (M/F)
1 x	Stickers-digit for marking
1 x	6 mm aluminium horn with patella
1 x	ABS tube 10.0x8.0x1000 mm
1 x	Cable with accesories
1 x	ABS tube 5.0x3.0x1000 mm
1 x	Steel tube (L 1000 mm Ø6 mm, Ø5,7 mm)
2 x	Aluminium tube (L 1000 mm, Ø3.0 mm, Ø2.1 mm)
1 x	CF tube set (Ø 38 mm y Ø 14 mm)
1 x	Steel tube (L 1000 mm Ø7 mm, Ø6,7 mm)
1 x	Nylon hinge for flaps 33x9 (2 pcs)
1 x	Pin type hinge Al 3,0x50 mm (2 pcs)
1 x	Miniature brass strap hinge, 1 m
1 x	Futaba male 40 cm extension
1 x	M3 black washers (4 pcs)
1 x	Quicklock washer 2 mm (10 pcs)
1 x	Extension silicon 75 cm (Futaba)
1 x	Extension silicon 30 cm male (Futaba)
1 x	Extension silicon 30 cm female (Graupner)
1 x	Cabel "Y" 15 cm
1 x	Futaba Female 40 cm extension
1 x	Lock washer 2.2 mm (20 pcs)
1 x	33 x 8 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x	25 mm reinforced hinge
1 x	Extension silicon 30 cm female (Futaba)
1 x	Cable S.BUS 3 salidas 300 mm
1 x	Cable silicona female batt. receptor 30 cm (Futaba)
1 x	Quicklock washer 4 mm (10 pcs)
1 x	67 mm cylidric hinge Ø 5 mm (4 pcs)
1 x	Circlik for shaft 1.9 mm (10 pcs)
1 x	Lock washer 2.7 mm (20 pcs)
1 x	0,14 mm PVC servo wire extension, ZH micro conector.
1 x	Extension 100 cm (Futaba)
1 x	Extension silicon 100 cm (Graupner)
1 x	Cabel "Y" 30 cm (graupner)
1 x	15 mm reinforced hinge
1 x	Quicklock washer 1 mm (10 pcs)
1 x	Extension 90 cm (Futaba)
1 x	43 x 10 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x	Flat washer 3.2 mm (20 pcs)
1 x	Circlick securite
1 x	Aluminium wide washer M3 red (4 pcs)
1 x	SERVO DES 568 MG
1 x	SC NAVY V15R
1 x	Propeller hub spacer 8/5.5
1 x	Distanzstück motor OS 120 AX
1 x	Brass rod Ø 1.5 mm x 1000 mm
1 x	Foam plastic plates (310x210x5 mm)
1 x	Receiver GRAUPNER GR-16 HoTT
1 x	Receiver replacement antenna, approx. 85
1 x	Manometer 4 mm
1 x	SERVO DES 658 BB MG
1 x	Recess mount-rem. glow plug set
1 x	GLOW 2C + accesories

1,993.49EUR