130.00EUR

Eachine EV800D 5 Inches 800x480 FPV VR Goggles Monitor
[ROIEV800D]


Gafas FPV Eachine EV800D

Dimension: 180*145*82mm
Weight: 362g without antenna
Belt : three-way adjustable belt

Specification
Build in DVR
Record up to 720*576px full frame rate video, no frame lost (C10 card required)
Replay in MENU
Require C10 card to record full frame rate
Diversity Super sensitiveness in 2pcs RX5808 PRO modules
Great performance when two types (Linear and Omni) antennas are used
Display Screen size: 5.0 inch
Screen resolution: 800*480(No blur after enlarge by the lens)
Screen brightness: 600cd/m2 with special high brightness backlight LED for outdoor FPV
View Angle: 140/120 degree(Horizontal/Vertical)
Lens 3x boost of the video to acquire intense feel-in-there video; 92% transparent rate distort if light;
Battery Built-in 7.4V/1200mAh battery;
Each battery circle offer around 2hr working time;
11-20V wide range recharging voltage range, typical recharging voltage is 12V 2S (7.4 V) /3S(11.1V) battery as back-up power t to have long working time.
Frequencies (5.8GHz, with RaceBand)
CH CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8
GROUP A or FR1 5865 MHZ 5845 MHZ 5825 MHZ 5805 MHZ 5785 MHZ 5765 MHZ 5745 MHZ 5725 MHZ
B or FR2 5733 MHZ 5752 MHZ 5771 MHZ 5790 MHZ 5809 MHZ 5828 MHZ 5847 MHZ 5866 MHZ
C or FR3 5705 MHZ 5685 MHZ 5665 MHZ 5645 MHZ 5885 MHZ 5905 MHZ 5925 MHZ 5945 MHZ
D or FR4 5740 MHZ 5760 MHZ 5780 MHZ 5800 MHZ 5820 MHZ 5840 MHZ 5860 MHZ 5880 MHZ
R or FR5 5658 MHZ 5695 MHZ 5732 MHZ 5769 MHZ 5806 MHZ 5843 MHZ 5880 MHZ 5917 MHZ

Features:
Built-in with super HD DVR record up to 720*576px resolution
Diversity RaceBand 40ch Auto-Searching
Two system (Display/Record duo core separated chipsets ) ensure no delay in displaying and no frame lost in recording(please use C10 super speed card to ensure the full frame recording)
Work friendly with pilot-OSD, no block on the important flying OSD information; Separable design, 5 inch screen can be used as small monitor on radio controller or with tripod;
HD high brightness 5 inch LCD specially tuned for FPV racing;
Diversity function, Built-in super sensitive 5.8GHz 40ch receiver module, with RaceRand;
Advanced auto-searching function and the working frequency show on screen;
Built-in 7.4V 1200mAh battery, each full charge offer 2 hours working time;
Wide range re-charge voltage 11-20V;
Accept 2S or 3S batteries as back-up power source, to prolong the working time; Nice ergonomic design and fit different faces;
Super-wide visible angle up to 82 degree;
92% transparent lens adopted, no distort, no blur on the edge of screen;
Light weight 375g with 3.5 hr 2000mAh battery, RTF for any scale racing game;
5 Inch 800*480px HD high brightness LCD

Package Included :
+ 1 x Eachine EV800D
+ 1 x Charger
+ 1 x 5.8G halfplanner antenna with RP-SMA connector
+ 1 x 5.8G RHCP cloverleaf antenna with RP-SMA connector
+ 1 x AVin cable
+ 1 x DCpower cabler to 3S balancer plug cable
+ 1 x Fresnel lens clearning kit
+ 1 x Instruction manual (English)


few units
few units

Reviews
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x Round Rod 1,25x1000 mm
1 x Strip 1,5x1,5x330 mm
1 x Strip 3,5x1,75x330 mm
1 x ABS Strip 1.5x3.0x1000 mm
1 x ABS Strip 1.0x4.0x1000 mm
1 x ABS Strip 1.5x4.0x1000 mm
1 x ABS I Strip 10x5x1000 mm
1 x Strip ABS 2.0x8.0x1000 mm
1 x Round Rod 1,0x1000 mm
1 x ABS Strip 1.0x3.0x1000 mm
1 x Strip ABS 2.0x5.0x1000 mm
1 x Round Rod 6,0x1000 mm
1 x ABS Strip 1.5x2.0x1000 mm
1 x ABS Strip 1.5x8.0x1000 mm
1 x Strip ABS 2.0x3.0x1000 mm
1 x Strip 2,5x1,25x330 mm
3 x Savox Highvoltage Brushless Servo SB-2272MG (Tail rotor)
2 x SAVOX SH 0254 servo
3 x Savox HV Brushless Servo SB-2270SG (Swashplate)
1 x Cierre cabina aluminio Ø5, I=16 mm
1 x Stainless steel cable Ø 0.5 mm (20 m)
2 x Aluminium alloy coupler for carbon tube 6/M4
1 x Canopy Lock V1 M3 Red (2 pcs)
1 x Locking cable tie 4.6x203 (uds)
2 x Screw-lock pushrod conn snap Ø 1.5 mm (2 uds)
1 x Crimping sleeves for cable 0.70 mm (10 pcs)
1 x 1/4 Pilot "Heidi"
1 x 1/6 Pilot "Tony"
1 x 1/6 Pilot "Cindy"
1 x Piloto WWII USAAF 12" Scale 1/6 - 1/5
2 x Civilian pilot "Curt" size 9cm (Slimline)
1 x Pilot JAN 1/4 Saiplanes
1 x Piloto Jet "Red" 1/6 Scale
1 x Piloto jet 130 mm
1 x 1/10 Pilot "Jimmy"
2 x Civilian pilot "Pamela" size 9cm (Slimline)
1 x 1/12 Pilot "Cougar"
1 x Civilian pilot "G-Man" size 9cm (Slimline)
2 x Piloto Jet "Green" 1/6 Scale
1 x 1/12 Pilot "Langley"
2 x 1/4 Pilot "Mike"
2 x Pilot WWII US Navy Pacific 12" Scale 1/6-1/5
1 x Civilian pilot "Gramps" size 9cm (Slimline)
1 x Piloto JET 1:3,5
1 x 1/6 Pilot "Garry"
1 x Pilot "Goose" (Slimline)
2 x Militarian pilot "Kamikaze" size 9cm (Slimline)
1 x MYLAR film A350 (1000x500 mm)
1 x Extension 90 cm (Futaba)
1 x Propadapter for motor A60-V2
1 x Shaft for A60-XS-V2 (112,5mm)
1 x JETImodel Addcap 820
1 x 10 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x Strip 2,0x2,0x330 mm
1 x TX 250 mW especial GOPRO
3 x Optical RPM Sensor
1 x ABS Strip 1.0x5.0x1000 mm
2 x Motor Moki S 250 cc 5 cyl with autostarter
1 x Split M1,2x10 (10 pcs)
1 x Tip wing protector 30x10 (2 pcs)
2 x Cable grommet Ø 5 mm (4 uds)
1 x Servo inverter
2 x Servo inverter
1 x 28x5 mm wires output (2 pcs)
1 x Micro screw-lock pushrod conn snap Ø 1 mm (2 uds)
1 x Steering arm 16 mm Ø 3 mm (2 uds)
2 x Allen wheel collar M4x4
1 x Fully Threaded Steel Rod SUS303 70mm M3 (2 pcs)
1 x Fully Threaded Steel Rod alumin 90 mm M3 (2 pcs) knurled
1 x Camera Sony 4140+673 CCD with Built-in 200mw TX + antenna
1 x U Profile ABS 5,0x10,0x1000 mm
1 x Profile ABS half cane 2.5x1000 mm
2 x Profile ABS Square 3 x 1000 mm
1 x Streamline Stainless Steel Tubing 7.5x4.5x1000 mm
1 x U Profile ABS 3,0x6,0x1000 mm
1 x ABS angle 4,0x4,0x1000 mm
2 x Profile ABS Square 2 x 1000 mm
1 x Profile ABS Square 1 x 1000 mm
1 x T-Connector 4.0 mm x 1000 mm
1 x Profile ABS half cane 2.0x1000 mm
1 x ABS angle 6,0x6,0x1000 mm
1 x Streamline Stainless Steel Tubing 15.5x8.5x1000 mm
1 x Short ball link M1.6 (6 uds)
1 x M2,5 Diam metal short ball link V3 (2 pcs)
1 x M2/M1/6 3Diam short black ball link V1 (2 pcs)
1 x Long ball link M3 (6 uds)
1 x SSPS105 Super Hi-Power servo
2 x Interruptor RX/Batterie
2 x "Y" charging 4mm wire (2 IN-1 OUT).
2 x Balanceradapter JST-XH (Heli 47G) 2-6 c.
1 x Female connector for 6 pines AWG
1 x BULL MØ1 2.600mm BLUE
2 x Fully Threaded Steel Rod alumin 50 mm M3 (2 pcs)
1 x Fully Threaded Steel Rod Duralumin 120 mm M3 (2 pcs)
1 x Fully Threaded Steel Rod SUS303 65 mm M3 (2 pcs)
1 x Pushrod greyline 4/3 with coupler M3
1 x Motor DLE 30 cc V2
1 x ZENOAH ZG 26SC with magneto ignition
1 x Motor UMS Radial-7-50cc gas
1 x Cylinder-piston Assembly 30cc
1 x Rear cover O-ring 26/30 cc
1 x Head Gasket 30cc (3 pcs)
1 x Motor DLE 55 RA
1 x Carburador DA-35, DA-50R-DA-100L , VM-60/70
1 x Piston ring for DA-85 and DA-170
1 x Motor NGH GF 150 R5
1 x Cylinder DA-50R, DA-100, DA-100L
1 x Electric starter suitable for the DLE111, DLE120 and DLE85.
1 x Ignition KOLM BX-155-2 Engine
2 x Drilling-template set for Moki engines Moki S150, S180, S215, S2
1 x Stainless Steel Bend D 15x0,4mm
1 x Giant Scale Muffler D.A. 170 (2 pcs)
1 x Tufnol Choke Lever Arm d=4,7mm
2 x Motor Moki S 400 cc 5 cylinders
1 x DA 70 Twin Gas Engine
1 x DYNAMOMETER S-1580
2 x Female connector JST SH 1.0mm with 10 cm wire
2 x TrainerCord (master-learner)
1 x Adapter 3,0 mm M8
1 x 2 mm Prop Adapter M5
1 x Adapter 3,2 mm M5 for spinner 30 mm fixed propeller
1 x Landing gear frontal support 29x26x13,5
1 x Sparkplug Champion RCJ-7Y for ZG
1 x Sparkplug NGK CM6
1 x Connector CAN 15
1 x PSC 6
1 x 30 cm BEC cable (female)
1 x Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm)
1 x Woodruff key for DA50/85/100/150 and DA 200
1 x Joint for DA-50 reed valv
1 x Escape Moki 100 BVT
2 x Motor Moki 180
1 x Motor MOKI S 250 cc 7-cylindrer
1 x Carburator Moki S400
2 x Pick up for motor Moki 250 cc 7 cylinders
1 x MOKI S250 Intake Bend
1 x Adapter 5,0 mm M8
1 x Aluminun wheel collar 3 mm Ø (4 uds)
1 x Adapter 3,2 mm M8
1 x Adapter 3,2 mm M6
1 x Professional Servo tester
1 x 4 mm Prop Adapter M6
1 x Fully Threaded Steel Rod M3
1 x Tip wing protector 28x10x12 (2 pcs)
1 x Fully Threaded Steel Rod alumin 80 mm M3 (2 pcs)
1 x Fully Threaded Steel Rod alumin 60 mm M2,5 (2 pcs)
1 x Steering arm 12 mm Ø 4 mm
1 x Pushrod octagone 4/3
1 x Press fitting for 0,5 diam. steel cable (10 pcs)
1 x Locking cable tie 2.5x100 (uds)
1 x 800TVL CMOS camera for FPV
1 x ABS "T" angle 2.0x2.0x1000 mm
1 x ABS "T" angle 8.0x8.0x1000 mm
1 x Profile ABS triangular 6.0x1000 mm 90º
1 x Sparkplug 1/4-32 EVO 10GX
1 x Sparkplug 1/4-32 Glow
1 x Sparkplug DLE CM6
1 x DLE 111 pipe plug
1 x Bujia OS G5 gasolina
1 x Male connector for 6 pines AWG
1 x Connector Sub-D 2+5 Female
1 x CellPRO 4S Adaptader (GP/KO up to 4S)
1 x Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm)
1 x 30 cm BEC cable (male)
1 x 3 LiPo XH>EH adapter
1 x Copper lacquer wire Ø0,2 mm (5 m)
1 x PSC 5
1 x CC 03
1 x Prolonguer for Balancer Thunder Power 6S
1 x USB interface ALTIS
1 x Black copper lacquer wire Ø0,2 mm (5 m)
1 x Male Prolonger TP 4/5S
1 x 4 LiPo XH>EH adapter
1 x Red copper lacquer wire Ø0,2 mm (5 m)
1 x 2 LiPo XH>EH adapter
1 x Cabel charger battery transmiter Futaba 2x0,5 qmm (50 cm)
1 x Female prolonguer XH 30 cm 6 cell cable of silicone 0,25 mm
1 x CC 01
1 x Fully Threaded Steel Rod M2,5 (2 uds)
1 x 41x5,5 mm wires output (2 pcs)
1 x Clip fixing for wing (2 pcs)
1 x 250 mm / 16 mm Airbrakes
1 x Cockpit aluminium closing
1 x 140 mm rods + T patellas set for direction control
1 x Wing bolts M6 Steel screw Red (2 pcs)
1 x Gasket carburetor carrier->crankcase DA-85 DA-100L DA-120 DA-200
1 x Carburetorgasket DA-85, DA-100, DA-100L and DA-120
1 x Gasket, Carburetor DA-150/170
1 x Gasket for motor DA 50-R
1 x Metal gasket elbow/cilinder DA60R/DA120
1 x Gasket, from red carb carrier to crankcase DA-150L/170
1 x Reed valves with doubler, set for DA 85/100/120
2 x Flange gasket MOKI carburetor
1 x Motor DA 50-R
1 x Pilot "Anthony" (Slimline)
1 x SCHARNHORST Battleship 1:200
2 x Moki Carburetor Throttle Arm with Extension
2 x Baffles for Radial Moki S180/320 mm
1 x Motor Moki S 300 cc 5 cylinders
1 x 1/7 Pilot "Japanese"
2 x Motor MOKI 160 BVT boxer 4-stroke
1 x Carburator gasket MOKI
1 x Moki Exhaust Bend 50VT
1 x Carburator Moki S 180
1 x Carburator Moki S250
1 x Motor MOKI S 350 cc 7 cylinder
1 x Baffles for Radial Moki S250/330 mm
1 x Motor Moki S 250 cc 5 cylinders
1 x Motor Moki 100 BVT
1 x Moki Pushrod S250 (1 pcs)
1 x Flat Connector 4.0 mm x 1000 mm
1 x Regler autostarter MOKIS250
1 x Air filter MOKI
1 x La Capitania di Venetia 1:50
69,472.12EUR
Manufacturers
Manufacturer Info
Roi-Import
Roi-Import Homepage
Other products
Languages
Español English
Currencies