130.00EUR

Eachine EV800D 5 Inches 800x480 FPV VR Goggles Monitor
[ROIEV800D]


Gafas FPV Eachine EV800D

Dimension: 180*145*82mm
Weight: 362g without antenna
Belt : three-way adjustable belt

Specification
Build in DVR
Record up to 720*576px full frame rate video, no frame lost (C10 card required)
Replay in MENU
Require C10 card to record full frame rate
Diversity Super sensitiveness in 2pcs RX5808 PRO modules
Great performance when two types (Linear and Omni) antennas are used
Display Screen size: 5.0 inch
Screen resolution: 800*480(No blur after enlarge by the lens)
Screen brightness: 600cd/m2 with special high brightness backlight LED for outdoor FPV
View Angle: 140/120 degree(Horizontal/Vertical)
Lens 3x boost of the video to acquire intense feel-in-there video; 92% transparent rate distort if light;
Battery Built-in 7.4V/1200mAh battery;
Each battery circle offer around 2hr working time;
11-20V wide range recharging voltage range, typical recharging voltage is 12V 2S (7.4 V) /3S(11.1V) battery as back-up power t to have long working time.
Frequencies (5.8GHz, with RaceBand)
CH CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8
GROUP A or FR1 5865 MHZ 5845 MHZ 5825 MHZ 5805 MHZ 5785 MHZ 5765 MHZ 5745 MHZ 5725 MHZ
B or FR2 5733 MHZ 5752 MHZ 5771 MHZ 5790 MHZ 5809 MHZ 5828 MHZ 5847 MHZ 5866 MHZ
C or FR3 5705 MHZ 5685 MHZ 5665 MHZ 5645 MHZ 5885 MHZ 5905 MHZ 5925 MHZ 5945 MHZ
D or FR4 5740 MHZ 5760 MHZ 5780 MHZ 5800 MHZ 5820 MHZ 5840 MHZ 5860 MHZ 5880 MHZ
R or FR5 5658 MHZ 5695 MHZ 5732 MHZ 5769 MHZ 5806 MHZ 5843 MHZ 5880 MHZ 5917 MHZ

Features:
Built-in with super HD DVR record up to 720*576px resolution
Diversity RaceBand 40ch Auto-Searching
Two system (Display/Record duo core separated chipsets ) ensure no delay in displaying and no frame lost in recording(please use C10 super speed card to ensure the full frame recording)
Work friendly with pilot-OSD, no block on the important flying OSD information; Separable design, 5 inch screen can be used as small monitor on radio controller or with tripod;
HD high brightness 5 inch LCD specially tuned for FPV racing;
Diversity function, Built-in super sensitive 5.8GHz 40ch receiver module, with RaceRand;
Advanced auto-searching function and the working frequency show on screen;
Built-in 7.4V 1200mAh battery, each full charge offer 2 hours working time;
Wide range re-charge voltage 11-20V;
Accept 2S or 3S batteries as back-up power source, to prolong the working time; Nice ergonomic design and fit different faces;
Super-wide visible angle up to 82 degree;
92% transparent lens adopted, no distort, no blur on the edge of screen;
Light weight 375g with 3.5 hr 2000mAh battery, RTF for any scale racing game;
5 Inch 800*480px HD high brightness LCD

Package Included :
+ 1 x Eachine EV800D
+ 1 x Charger
+ 1 x 5.8G halfplanner antenna with RP-SMA connector
+ 1 x 5.8G RHCP cloverleaf antenna with RP-SMA connector
+ 1 x AVin cable
+ 1 x DCpower cabler to 3S balancer plug cable
+ 1 x Fresnel lens clearning kit
+ 1 x Instruction manual (English)


few units
few units

Reviews
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x 30 cm MULTIPLEX female connector
2 x Connectors banna oro 0,8 mm (M/F)
1 x Connectors banna oro 6,0 mm (M/F)
1 x Banna gold connector 2,5 mm (M/F)
1 x Conector FUTABA Servo male BLUE silicon (10 pcs)
1 x Connectors banna gold 5,5 mm (M/F)
1 x Conector JR Servo female (10 pcs)
1 x Connectors DEANS 4 pins (1 pair)
1 x Connectors banna oro 8,0 mm (M/F)
1 x Conector BEC male (10 pcs)
1 x Conector JR Servo male (10 pcs)
1 x 2 mm male connector (2 pcs) with safety connector
1 x Connectors banna oro 2 mm (M/F)
1 x Conector FUTABA Servo male (10 pcs)
1 x Connectors banna oro 3,5 mm (M/F)
1 x 2 mm female connector (2 pcs) with safety connector
1 x Connectors banna oro 8,0 mm (Male) 5 pcs.
1 x Conector JR Servo female (10 pcs)
1 x Connector CAN 15
1 x Connectors banana oro 6,0 mm Ultralight (M/F)
1 x Connectors banna oro 8,0 mm 5 pcs(Female)
1 x Connectors banna oro 4 mm (M/F) (ultralight)
1 x Conector JR/Uni Servo female BLUE silicon (10 pcs)
1 x Connectors banna oro 3 mm (M/F)
1 x Connectors banna oro 4 mm (M/F)
1 x Connectors DEANS (T)
1 x 30 cm DEANS female connector
1 x Bag connector 2 mm
1 x Disposable Injector Bags (30x16cm) 100 pcs
1 x Copier 5x20 cm pcs
2 x Propeller balancer
3 x 
1 x Propeller balancer
2 x Z Bender - S Type Tool
2 x Vacuum pump P1-N
2 x 3,0x60 mm allen screwdriver
1 x Surface Indicator Gauge Small
2 x Crimping tool
4 x PROXXON - SILICON CARBIDE BELTS FOR BSL 220/E
3 x PROXXON - SANDING BELTS FOR BSL 220/E 180 GRIT (5 pcs)
1 x 1,5x50 mm allen screwdriver
1 x Cut tube
2 x Digital precision scale up to 2000 g
2 x PROXXON - SANDING BELTS FOR BSL 220/E 120 GRIT (5 pcs)
1 x Hot Glue Stick GREEN
3 x Starter Sullivan-STAR 603 DINATRON
2 x Starter EM Gear Power 250
2 x 2,5x60 mm allen screwdriver
2 x Medidor ángulos y/o incidencias
2 x Screwdriver for Hexagon 1,5mm
1 x Copier 2x20 cm pcs
1 x Hot Glue Stick BLACK
1 x WingFix ULTRA Black Edition
2 x Hot Glue Stick RED
1 x Hexagonal ball head 2.0 x 50 mm
1 x Field folding model stand
1 x Ball Link Plier
2 x Screwdriver for Torx® TX6
2 x 2,0x50 mm allen screwdriver
2 x Vacuum Connection VA 1 (for hose Ø 6 mm)
2 x PROXXON - SANDING BELTS FOR BSL 220/E 80 GRIT (5 pcs)
3 x Starter 12v (Max 180 and 30ccm)
2 x BALSA triangular 10x10x1000 mm
1 x Walnut wood slat 2.0x2.0x1000 mm
1 x Pine wood slat 5.0x5.0x1000 mm
2 x Linden wood slat 2.0x2.0x1000 mm
2 x Walnut wood slat 3.0x3.0x1000 mm
1 x Beech dowels 2.0 x 1000 mm
1 x BALSA triangular 6x6x1000 mm
1 x Pine wood slat 3.0x7.0x1000 mm
2 x Pine wood slat 6.0x6.0x1000 mm
1 x Pine wood slat 3.0x10.0x1000 mm
1 x Pine wood slat 1.5x3.0x1000 mm
2 x BALSA trip 5.0x5.0x1000 mm
1 x Pine wood slat 3.0x5.0x1000 mm
2 x BALSA trip 4.0x4.0x1000 mm
1 x BALSA triangular 15x15x1000 mm
1 x Beech dowels 10 mm x 1000 mm
2 x Walnut wood slat 1.5x1.5x1000 mm
2 x BALSA trip 3.0x5.0x1000 mm
1 x BALSA triangular 8x8x1000 mm
1 x Beech dowels 4.0 x 1000 mm
2 x Mahogany wood slat 1.5x1.5x1000 mm
2 x Beech dowels 3.0 x 1000 mm
2 x Mahogany wood slat 2.0x2.0x1000 mm
2 x BALSA trip 10x10x1000 mm
2 x Pine wood slat 2.0x10.0x1000 mm
1 x LOWER TOW HOOK
1 x Conector JR Servo male (10 pcs)
1 x Pin type hinge Al 6x98 mm (2 pcs)
1 x Carbon fiber rod 0.8 mmx1000 mm
2 x A/C quality beech plywood 600x300x6.0 mm
1 x Straightened rod Ø 14.0 mm x 1000 mm
1 x Civilian pilot "G-Man" size 9cm (Slimline)
1 x Conector BEC female (10 pcs)
1 x BEC 3A FOXY
1 x "Y" charging 4mm wire (2 IN-1 OUT).
1 x Conector FUTABA Servo female (10 pcs)
2 x Dust collector for mould cleaning
2 x Starter EM Gear Power 80
2 x Z Bender - S Type Tool
1 x Fresa corte diamante Ø 2.35mm (flame)
2 x Soldering tip for KAVAN soldering iron KAV66.8338
2 x Fabric scissors curved Premium, 16 cm / 6" length
2 x Wooden mouth spatulas (150 x 18 x 1.5 mm), 100 pcs
1 x Set brocas Ø 2.0-2.2-2.4-2.6 mm (4 pcs)
3 x Propeller diller for DLE111 and DA85-150
1 x Truck-trailer for gliders 720 x 239 mm
2 x 120x60 mm SLH KOVO wheel
1 x Liferaft 47 mm
1 x Angle of incidence meter
1 x Ball Link Plier
2 x Angle measurer
2 x Vacuum pump 12 CFM
1 x BALSA trip 6.0x6.0x1000 mm
1 x A/C quality beech plywood 600x300x0.6 mm
1 x BALSA leading edge 8x10x1000 mm
1 x Balsa panel 1.0x100x1000 mm
1 x Linden wood slat 3.0x3.0x1000 mm
1 x Smoke set "S"
1 x Blue smoke canister 100 g
1 x Initior Receiver FRX2 Wireless
1 x Green smoke canister 140 g
1 x Electric rocket starters (6 pcs)
1 x Blue smoke canister 140 g
1 x Yellow smoke canister 100 g
1 x 800TVL CMOS camera for FPV
1 x Initior Transmitter FTX2 Wireless
1 x AX-60 starters (5 pcs)
1 x White smoke bombs AX-9 (10 pcs)
1 x 3l Smoke oil
1 x AX-60 starters (5 pcs)
1 x Softshell Hispano Aviación
1 x Balsa panel 1.5x100x1000 mm
1 x BALSA trip 2.0x2.0x1000 mm
1 x A/C quality beech plywood 1520x750x4.0 mm
1 x Balsa panel 2.5x100x1000 mm
1 x Balsa panel 3.0x100x1000 mm
1 x BALSA trip 8.0x8.0x1000 mm
1 x Pine wood slat 10x10x1000 mm
1 x Liston HAYA 10 x 10 x 1000 mm
1 x Balsa panel 2.0x100x1000 mm
1 x Bandera Frankr 4x6
1 x Ancla 35 x 22 mm (2 pcs)
1 x Sanyo RX Battery Eneloop RX 4,8 V Futaba
1 x MG cannon 1.8 cm (5 pcs)
1 x Fresa corte diamante Ø 2.7mm (bola)
2 x Set fresas corte Vanadium Ø 2.3/2.35 mm (3 pcs)
2 x PROXXON - SAW BLADE OZI/E, 65MM, 160 TOOTH
1 x Propeller diller for DLE170
2 x Rubber Insert hard, 1 Pcs.
1 x Screwdriver for Hexagon 1,27mm
2 x Tool for entel
1 x Carbon fiber rod 1.5 mm x 2000 mm
1 x CA Glue fast 20g
1 x Carbon fiber rod 3.0 mm x 1000 mm
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x1.2 mm (10 pcs)
1 x Carbon fiber flat 1000x6.0x0.8 mm
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x4.0 mm (5 pcs)
1 x Smart Soldering Iron 110W/230V AC
1 x Set fresas corte acero-carburo Ø 1.8/2.3 mm (2 pcs)
1 x Set fresas corte Vanadium Ø 2.3/2.35 mm (3 pcs)
1 x Sun Cover ULTIMATUM 2.0 (Hispano Aviacion)
2 x Sub-D Plug Mold
1 x 25 mm Sandpaper file
1 x Spare round blades, 28 mm, pack/ 2 pcs.
1 x Tube bender
2 x Set brocas Ø 0.4-0.6-0.8-1.0 mm (4 pcs)
2 x Screwdriver for Torx® TX8
2 x Schul-Malpinsel Gr.5
1 x Pump hose (Ø 6/8 mm) transparent
1 x PROXXON - SAW BLADE HSS (50MM - 100T) (28020)
1 x PERMAGRIT Sanding Block 45° 140x51 mm
1 x HPP-21 PLUS PC Programmer for Hitec Digital Servos
1 x Mini Lock Grips 2PCS
2 x XT-60 Plug Mold
2 x Sealing Iron STANDARD
1 x Digital scale up to 40 kg
1 x Universal Filter
2 x PROXXON - SAW BLADE DIAMOND OZI/E
1 x Roller cutter 28 mm
1 x Llave dinamomterica 74 Z 0 0 21
1 x Modelling compound (Plastilin), sculptor's quality 1 Kg
1 x Propeller diller for EME35 and DLE35
2 x Pistola termica MH 550 micro
2 x MPX plug mold V1
1 x Propeller drill jig DA-35/50/60/70
2 x Mini Infrared Thermomiter
1 x Propeller drill jig DA 100/85/120/150/200 and VM 60-210
1 x Fabric scissors curved (offset handles), 16 cm / 6" length
2 x Mold plugs XT-90
1 x Mini-handed clamp
1 x Propeller diller for DLE30/DLE35RA/DLE40/DLE55/DLE61/EME 55/DA-5
1 x Welder 100W/200V
1 x PROXXON - SAW BLADE (50MM - 20T) (28017)
1 x Tachometer HANGAR 9 digital
1 x Propeller diller 5/6,3/8/9
1 x Tool for entel
1 x Sandpaper file 13 mm
1 x Rubber Insert soft, 1 Pcs.
1 x Starter 12v (Max 90 and 15ccm)
1 x Propeller diller for DA50, DLE55 red
1 x Laminating brush 10 mm, pack/ 50 pcs
2 x MPX 8 pins plug mold
1 x Extra Hard Titanium Herxagon Screwdrivers
2 x Sealing Iron Profi LCD
1 x Heat Seal Iron
2 x PROXXON - TRIANGLE / DELTA SANDING MACHINE OZI/E
1 x Carbon fabric 160 g/m² (plain weave) 100 cm x 2 m
1 x Buy Perforated film 100 cm / 20 m
1 x Carbon fabric 68 g/m² (style 493 aero, plain weave) 100 cm
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x2.0 mm (10 pcs)
1 x Buy Perforated film 145 cm / 50 m
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x2.0 mm (20 pcs)
1 x Carbon fabric 200 g/m² (Aero, plain weave) 100 cm x 5m
1 x Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 50 m
1 x Breatex™ Non-woven absorber 300 g/m² Roll 41 m
1 x Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 10 m
1 x Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 50 m
1 x CA Glue (medium) 20g
1 x Breatex™ Non-woven absorber 150 g/m² Roll 20m
1 x Breatex™ Non-woven absorber 150 g/m² Roll 50m
1 x Buy Perforated film 100 cm / 50 m
1 x Carbon fabric 160 g/m² (twill weave) 127 cm, roll/ 10 m
1 x Carbon Fiber TeXtreme® 80 g/m² (plain) 100 cm, roll/ 10 m
1 x A/C quality beech plywood 600x300x0.8 mm
1 x Carbon fabric 160 g/m² (plain weave) 100 cm x 3 m
1 x Buy Perforated film 100 cm / 10 m
1 x Set brocas Ø 1.5-2.0-2.5-3.0 mm (4 pcs)
1 x Steel brush wheel with 2.35mm
1 x PROXXON - SAW BLADE 8MM 0ZI220E
1 x Sealing Iron Sleeve STD
1 x Set fresas corte acero-carburo Ø 0.5/1.8 mm (2 pcs)
1 x FOXY G2 C3530-700
1 x Sun Cover BULL Mo1 2.6 (Hispano Aviacion)
1 x Cable video GoPro and 5V cable
11,862.27EUR
Manufacturers
Manufacturer Info
Roi-Import
Roi-Import Homepage
Other products
Languages
Español English
Currencies