130.00EUR

Eachine EV800D 5 Inches 800x480 FPV VR Goggles Monitor
[ROIEV800D]


Gafas FPV Eachine EV800D

Dimension: 180*145*82mm
Weight: 362g without antenna
Belt : three-way adjustable belt

Specification
Build in DVR
Record up to 720*576px full frame rate video, no frame lost (C10 card required)
Replay in MENU
Require C10 card to record full frame rate
Diversity Super sensitiveness in 2pcs RX5808 PRO modules
Great performance when two types (Linear and Omni) antennas are used
Display Screen size: 5.0 inch
Screen resolution: 800*480(No blur after enlarge by the lens)
Screen brightness: 600cd/m2 with special high brightness backlight LED for outdoor FPV
View Angle: 140/120 degree(Horizontal/Vertical)
Lens 3x boost of the video to acquire intense feel-in-there video; 92% transparent rate distort if light;
Battery Built-in 7.4V/1200mAh battery;
Each battery circle offer around 2hr working time;
11-20V wide range recharging voltage range, typical recharging voltage is 12V 2S (7.4 V) /3S(11.1V) battery as back-up power t to have long working time.
Frequencies (5.8GHz, with RaceBand)
CH CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8
GROUP A or FR1 5865 MHZ 5845 MHZ 5825 MHZ 5805 MHZ 5785 MHZ 5765 MHZ 5745 MHZ 5725 MHZ
B or FR2 5733 MHZ 5752 MHZ 5771 MHZ 5790 MHZ 5809 MHZ 5828 MHZ 5847 MHZ 5866 MHZ
C or FR3 5705 MHZ 5685 MHZ 5665 MHZ 5645 MHZ 5885 MHZ 5905 MHZ 5925 MHZ 5945 MHZ
D or FR4 5740 MHZ 5760 MHZ 5780 MHZ 5800 MHZ 5820 MHZ 5840 MHZ 5860 MHZ 5880 MHZ
R or FR5 5658 MHZ 5695 MHZ 5732 MHZ 5769 MHZ 5806 MHZ 5843 MHZ 5880 MHZ 5917 MHZ

Features:
Built-in with super HD DVR record up to 720*576px resolution
Diversity RaceBand 40ch Auto-Searching
Two system (Display/Record duo core separated chipsets ) ensure no delay in displaying and no frame lost in recording(please use C10 super speed card to ensure the full frame recording)
Work friendly with pilot-OSD, no block on the important flying OSD information; Separable design, 5 inch screen can be used as small monitor on radio controller or with tripod;
HD high brightness 5 inch LCD specially tuned for FPV racing;
Diversity function, Built-in super sensitive 5.8GHz 40ch receiver module, with RaceRand;
Advanced auto-searching function and the working frequency show on screen;
Built-in 7.4V 1200mAh battery, each full charge offer 2 hours working time;
Wide range re-charge voltage 11-20V;
Accept 2S or 3S batteries as back-up power source, to prolong the working time; Nice ergonomic design and fit different faces;
Super-wide visible angle up to 82 degree;
92% transparent lens adopted, no distort, no blur on the edge of screen;
Light weight 375g with 3.5 hr 2000mAh battery, RTF for any scale racing game;
5 Inch 800*480px HD high brightness LCD

Package Included :
+ 1 x Eachine EV800D
+ 1 x Charger
+ 1 x 5.8G halfplanner antenna with RP-SMA connector
+ 1 x 5.8G RHCP cloverleaf antenna with RP-SMA connector
+ 1 x AVin cable
+ 1 x DCpower cabler to 3S balancer plug cable
+ 1 x Fresnel lens clearning kit
+ 1 x Instruction manual (English)


few units
few units

Reviews
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x2.0 mm (20 pcs)
1 x Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 10 m
2 x Carbon Non-Woven, 160 g/m² 127 cm 1 m
1 x Vacuum bag, 1200 mm x 50 m
1 x Carbon fabric 160 g/m² (plain weave) 100 cm x 2 m
1 x Carbon Fabric Prepreg 200 g/m² (twill 2/2) 100 cm, roll/ 1 m
1 x Carbon fibre tape 200 g/m² (unidirectional) 50 mm
1 x Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 50 m
1 x Fibra carbono 3k tela 160g/m2 100 cm x 5m
1 x Glass fabric tape 225 g/m² (Silane, plain) 40 mm X 100m
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x2.0 mm (10 pcs)
1 x Carbon roving DowAksa / 24k / 1600 tex
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x4.0 mm (5 pcs)
1 x Carbon Non-Woven, 160 g/m² 100 cm 25 m
1 x Glass fabric tape 49 g/m² (Interglas 02037, finish FE 600/800, p
1 x Glass fabric tape 130 g/m² (Silane, plain) 25 mm / 100M
1 x Carbon Non-Woven, 160 g/m² 100 cm 10 m
1 x Carbon fabric 200 g/m² (Aero, plain weave) 100 cm x 3m
1 x Fibra carbono tela 160g/m2 100 cm x 2 m (twill weave)
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x1.2 mm (10 pcs)
1 x Bec MR UBEC 5A (5v/6v/7v)
2 x Black copper lacquer wire Ø0,2 mm (5 m)
1 x TP/TopFuel - JST-EH 4/5S Adapter
2 x Smoke set "M"
1 x Balanceradapter JST-XH (Heli 47G) 2-6 c.
1 x "S" set for boats
1 x Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm)
1 x CC 05
1 x "Y" charging 4mm wire (2 IN-1 OUT).
1 x Cabel charger transmitter GRAUPNER
1 x Cabel charger battery transmiter Futaba 2x0,5 qmm (50 cm)
1 x JETImodel SINGLE BEC
2 x Remote electric ignition system
2 x CM-3
1 x White smoke bombs AX-9 (10 pcs)
2 x Red smoke bombs AX-60 (5 pcs)
1 x 4 LiPo XH>EH adapter
1 x Red smoke canister 140 g
1 x Futaba External voltage input cable Futaba CA-RVIN-700
2 x Yellow smoke canister 140 g
1 x 2 LiPo XH>EH adapter
1 x "S" set for planes
2 x USB HLS prog. interface
1 x White smoke canister 140 g
1 x Copper lacquer wire Ø0,2 mm (5 m)
1 x Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH
1 x TrainerCord (master-learner)
1 x Ventral support for AX-18/AX-60
2 x BEC 3A FOXY
1 x 14x60 mm Mini rings Tie Wraps (4 pcs)
2 x Foil for sticking flaps and ailerons
1 x Crimping tool
1 x Vacuum pump P1-N
1 x Screwdriver for Torx® TX6
1 x Xplorer2 anemometro
1 x Screwdriver for Hexagon 1,27mm
1 x Stickers-digit for marking
1 x Z Bender - S Type Tool
1 x Hot Glue Stick BLACK
1 x 
1 x Ball Link Plier
1 x Starter 12v (Max 180 and 30ccm)
1 x Hot Glue Stick GREEN
1 x Propeller balancer
1 x Covered closure or fairings
1 x BALSA trip 3.0x5.0x1000 mm
1 x Profile ABS triangular 4.0x1000 mm 90º
1 x Straightened rod Ø 2.0 mm x 1000 mm
1 x 1/6 Pilot "Tony"
1 x Breatex™ Non-woven absorber 150 g/m² Roll 5 m
1 x Micro Switch button
1 x wing/fuselage connector for 16 pines AWG 20-24
1 x Short Switch On/Off micro
1 x White smoke bombs AX-60 (5 pcs)
1 x AX-60 starters (5 pcs)
1 x Initior Receiver FRX2 Wireless
1 x Black smoke bombs AX-60 (5 pcs)
1 x Male connector for 16 pines AWG
1 x White smoke bombs AX-3 (10 pcs)
1 x SPARK Switch 7.4v
2 x Red copper lacquer wire Ø0,2 mm (5 m)
1 x SPARK Switch 5.9v
1 x JETImodel Addcap 1640
1 x Male connector JST SH 1.0mm with 10 cm wire
1 x Female connector JST SH 1.0mm with 10 cm wire
1 x Blue smoke canister 100 g
1 x MPX-Dean "T" Adapter
1 x TP/TopFuel - XH 2/3S Adapter
1 x Adapter lead MPX/XT60
1 x Carbon Non-Woven, 160 g/m² 100 cm 5m
1 x Carbon Non-Woven, 160 g/m² 127 cm 5m
1 x SE Ring 450 mm (2 pcs)
1 x SE Ring 330 mm (4 pcs)
1 x 20x200 mm battery rings
1 x 20 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x SE Ring 350 mm (2 pcs)
1 x 
1 x Spikes Band (5 m)
1 x Pin 3,0 to cable coupler M3,0 ⌀ (6 pcs)
1 x Metal clevis M3 (10 uds)
1 x Kwik link aluminio IZD. M3 L: 30mm (6 uds) pin Ø 2 mm
1 x Micro clevis (10 uds)
1 x Pulley brass 5/1,5 (2 pcs)
2 x Metal ball clevis M3 (10 uds)
2 x Metal clevis M2 (10 uds)
1 x Kwik link with arm M3xM2xL24
1 x Kwik link aluminio IZD. M2.5 L: 23mm (2 uds) pin Ø 1.6
1 x Ø 0,5 mm Pull-Pull Kevlar Line (3 m)
1 x Pulley brass 16/2 (2 pcs)
1 x Carbon fiber rod 2.0 mmx1000 mm
1 x Carbon fiber rod 20 mmx1000 mm
1 x Servo TOPMODEL STANDARD S3217
1 x Servo MKS HV6130
1 x Brazo servo MKS Metal M3-L:30 (2 pcs)
1 x XTorque CFK Servohebel 38
1 x Futaba 30 mm servo rounded arm
1 x 90x60 mm standart servo cover
1 x HPP-21 PLUS PC Programmer for Hitec Digital Servos
1 x Servo FUTABA HPS-A700 Digital S-Bus
1 x Servo Digital HITEC HS-5065 MG
1 x Servo GO-10S41MG 10.5 kg.cm 0.075s/60º
1 x Servo arm with 6 mm hole to FEMA 9800A
1 x Screws set for Hitec MG arms servo
1 x Servo HITEC HS-325 BB
1 x Servo GO-09 9g
1 x Servo RHINO pro SHV digi 4
1 x Extension 2/3 lipos JST - JST/C
1 x Selfstart electronic switch
1 x Switc electronic 30 Amp
1 x SPS 70V 100/200 A
1 x Female prolonguer XH 30 cm 6 cell cable of silicone 0,25 mm
1 x SWTU2 switch
1 x Extension 5 lipos JST - JST/C
1 x Extension 5 lipos JST/C - JST
1 x Prolonguer for Balancer Thunder Power 6S
1 x MAX BEC
1 x 19.5x13 Falcon electric 3-Blade carbon prop (54 g)
1 x Wing tips support for AX-18/AX-60 (2 pcs)
1 x 9x4.7 * 22x12 carbon propeller
1 x Kwik link aluminio M3 L: 30mm (6 uds) pin Ø 2 mm
1 x Pulley brass 10/2 (2 pcs)
1 x Eachine EV800D 5 Inches 800x480 FPV VR Goggles Monitor
1 x 21x14 Falcon electric carbon prop (64 g)
1 x Propeller 12x6 Falcon electric
1 x Conector MR-60 (pareja)
1 x M4xM2,5xL30 nylon clevis and arm (10 uds)
1 x Pulley brass 4/1,5 (2 pcs)
1 x Porta Kwik link M4 3 mm (2 pcs)
1 x Pin 2,0 to cable coupler M2,0 ⌀ (6 pcs)
1 x CNC FPV Display screen&Transmitter Holder Vertical
7,577.30EUR
Manufacturers
Manufacturer Info
Roi-Import
Roi-Import Homepage
Other products
Languages
Español English
Currencies