130.00EUR

Eachine EV800D 5 Inches 800x480 FPV VR Goggles Monitor
[ROIEV800D]


Gafas FPV Eachine EV800D

Dimension: 180*145*82mm
Weight: 362g without antenna
Belt : three-way adjustable belt

Specification
Build in DVR
Record up to 720*576px full frame rate video, no frame lost (C10 card required)
Replay in MENU
Require C10 card to record full frame rate
Diversity Super sensitiveness in 2pcs RX5808 PRO modules
Great performance when two types (Linear and Omni) antennas are used
Display Screen size: 5.0 inch
Screen resolution: 800*480(No blur after enlarge by the lens)
Screen brightness: 600cd/m2 with special high brightness backlight LED for outdoor FPV
View Angle: 140/120 degree(Horizontal/Vertical)
Lens 3x boost of the video to acquire intense feel-in-there video; 92% transparent rate distort if light;
Battery Built-in 7.4V/1200mAh battery;
Each battery circle offer around 2hr working time;
11-20V wide range recharging voltage range, typical recharging voltage is 12V 2S (7.4 V) /3S(11.1V) battery as back-up power t to have long working time.
Frequencies (5.8GHz, with RaceBand)
CH CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8
GROUP A or FR1 5865 MHZ 5845 MHZ 5825 MHZ 5805 MHZ 5785 MHZ 5765 MHZ 5745 MHZ 5725 MHZ
B or FR2 5733 MHZ 5752 MHZ 5771 MHZ 5790 MHZ 5809 MHZ 5828 MHZ 5847 MHZ 5866 MHZ
C or FR3 5705 MHZ 5685 MHZ 5665 MHZ 5645 MHZ 5885 MHZ 5905 MHZ 5925 MHZ 5945 MHZ
D or FR4 5740 MHZ 5760 MHZ 5780 MHZ 5800 MHZ 5820 MHZ 5840 MHZ 5860 MHZ 5880 MHZ
R or FR5 5658 MHZ 5695 MHZ 5732 MHZ 5769 MHZ 5806 MHZ 5843 MHZ 5880 MHZ 5917 MHZ

Features:
Built-in with super HD DVR record up to 720*576px resolution
Diversity RaceBand 40ch Auto-Searching
Two system (Display/Record duo core separated chipsets ) ensure no delay in displaying and no frame lost in recording(please use C10 super speed card to ensure the full frame recording)
Work friendly with pilot-OSD, no block on the important flying OSD information; Separable design, 5 inch screen can be used as small monitor on radio controller or with tripod;
HD high brightness 5 inch LCD specially tuned for FPV racing;
Diversity function, Built-in super sensitive 5.8GHz 40ch receiver module, with RaceRand;
Advanced auto-searching function and the working frequency show on screen;
Built-in 7.4V 1200mAh battery, each full charge offer 2 hours working time;
Wide range re-charge voltage 11-20V;
Accept 2S or 3S batteries as back-up power source, to prolong the working time; Nice ergonomic design and fit different faces;
Super-wide visible angle up to 82 degree;
92% transparent lens adopted, no distort, no blur on the edge of screen;
Light weight 375g with 3.5 hr 2000mAh battery, RTF for any scale racing game;
5 Inch 800*480px HD high brightness LCD

Package Included :
+ 1 x Eachine EV800D
+ 1 x Charger
+ 1 x 5.8G halfplanner antenna with RP-SMA connector
+ 1 x 5.8G RHCP cloverleaf antenna with RP-SMA connector
+ 1 x AVin cable
+ 1 x DCpower cabler to 3S balancer plug cable
+ 1 x Fresnel lens clearning kit
+ 1 x Instruction manual (English)


few units
few units

Reviews
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x Vest clothes Hispano Aviación
1 x Softshell Hispano Aviación
1 x Ballast 700gr OPALE
1 x Waterproof adhesive tape, width 19mm, length 25m
1 x Giant Scale Muffler SLIMLINE D.A. 100 (2pcs)
1 x Silencer with rear exhaust DA-120
1 x Extension S-Bus 1-2 silicon 30 cm FUTABA
1 x Pin type hinge Al 4,5x70 mm to wire (2 pcs)
1 x Spinner Alumin. fixed propeller 45 mm / 3,2 mm
1 x SE Ring 200 mm (2 pcs)
1 x Cabel "Y" 30 cm (Futaba)
1 x Canister combo DLE 120 cc
1 x Spinner 82mm Black ventilado
1 x Micro flex hinge (12 uds)
1 x servo adapter lead, JST-SH socket - JR male Pin, for GR-12SH+HoT
1 x Cable S.BUS 3 salidas 100 mm
1 x Pad Screw Mount M3, up to 3mm / 0.12″, (10 pcs)
1 x Stainless Steel Silencer side outlet for ZG 20/23/26
1 x 2,0x50 mm allen screwdriver
3 x Adjustable brass horn threaded M3
1 x Receiver Crystal 35 Mc/s Ch 62
2 x ABS "T" angle 4.0x4.0x1000 mm
1 x Propeller G-Sonic 20x8
1 x Digital precision scale up to 2000 g
1 x Ignition for ZG 20/26
1 x Carburettor Intake Bend for ZG38
1 x Distanzstück motor OS 120 AX
1 x 42 mm black plastic spinner for fixed propeller
1 x Carburetor DLE 30
1 x Cylynder DLE 20-RA
1 x M3-M4 rubber washer (8 pcs)
1 x Ball Link Plier
2 x Flap hinge (6 pcs)
1 x Receiver replacement antenna, approx. 15
1 x Aluminium wide washer M4 Gold (4 pcs)
1 x DLE 111 Carb gasket (V1)
2 x Streamline Stainless Steel Tubing 9.0x5.0x1000 mm
1 x 55% silver electrodes (2 pcs)
2 x Motor DA 150
2 x ABS "T" angle 10.0x10.0x1000 mm
2 x Motor DA 85
1 x Dremel 3000 130W
2 x 25 mm Sandpaper file
1 x DLE 85/111/120 Crankshaft keyway
1 x Canister combo DLE 120 cc
1 x Medidor ángulos y/o incidencias
1 x Horn DUBRO 1/2A
1 x Motor UMS Radial-5-150cc gas
1 x Cable grommet Ø 3.2 mm (4 uds)
1 x Rear cover O-ring 26/30 cc
2 x Horn mando small (2 pcs)
1 x 80 mm rods set for direction control
2 x Brass control horn M4 short for wire (4 pcs)
1 x Horn 20x28,5 mm (2 pcs)
2 x Brass control horn M2 short for wire (2 pcs)
1 x Carbon fibre sleeve 12k 170 mm x 5m
1 x Spinner NUT M5
1 x 140 mm rods set for direction control
1 x Ball link Aluminio M4 x 4 x 6 x 26mm (4 uds)
1 x Spinner NUT M5
1 x Kwik link AL M2,5 L:23 mm (2 pcs) + Pin Ø 1,6 mm
1 x Cable coupler M2 (10 uds)
1 x Surface Indicator Gauge Small
1 x Piston ring EME 35cc
1 x Propeller pad and output shaft EME 55/60 cc
1 x Compact Silencer KOLM BX-155
1 x EME ignition free wheel
1 x One Way bearing for EME55 starkit with key
2 x VBar NEO VLink 6.x Express, neon-yellow
1 x Piñon motor autostarter 35cc
1 x Pitts Mufflers EME 35 cc
1 x VBar Control Touch, midnight black
1 x 115x29 mm (4.50") Type jets aluminium core wheel
1 x 1/10 Pilot "Jack"
1 x Modulo telemetria 500 mW/100 mw Radio aire/Tierra Modulo 915 MHz
1 x ALPHA 1000mm BL ARTR
2 x TX 250 mW especial GOPRO
1 x TMM 2512-3S heli
2 x F9F COUGAR Grey ARF 1.562 mm
1 x L-39 Albatros Scale 1:4.75 1991 mm
1 x Electric Landing Gear ASPIRE
1 x Electric Landing Gear ODYSSEY (Elektron Retracts)
1 x Propeller POWER-PROP 7x7
1 x Bags de Luxe ASPIRE
1 x HAWKER HUNTER 1:5,8 Desert (1.770mm)
1 x HAWKER HUNTER 1:5,8 (1.770mm)
1 x 200 mm extensión servo HITEC/JR
1 x 20x200 mm battery rings
1 x 280 cc gasoline fuel tank complet
1 x 
1 x Cilinder joint for G230RC/G260RC
1 x Sparkplug Champion RCJ-7Y for ZG
1 x Profile ABS Square 1 x 1000 mm
1 x Savox Brushless Servo SC-1251 MG
1 x Servo SAVOX SH 0257 MG
1 x Bearing block for noseleg landing gear
1 x ABS angle 5,0x5,0x1000 mm
2 x U Profile ABS 2,0x4,0x1000 mm
2 x Profile ABS Square 4 x 1000 mm
2 x Streamline Stainless Steel Tubing 17.8x12.4x1000 mm
1 x Brass rod Ø 0.5 mm x 1000 mm
1 x ALU servo arm 3 mm shaft
1 x Hard brass tubing (L 1000 mm, Ø10.0 mm, Ø9.1 mm)
1 x Savox Brushless Servo SC-1267 SG
1 x U Profile ABS 1,0x2,0x1000 mm
1 x SAVOX SH 0255 MG servo
1 x Propeller CFK 17x18
1 x Servo RHINO pro SHV digi 4
1 x Propeller RF CFK 16x8,5 S
1 x Propeller CFK 23x12
1 x Propeller CFK 15x13
1 x Propeller CFK 12.5x7
1 x Propeller CFK 16x13
1 x Propeller CFK 14x8
1 x EC-Cutter
1 x Tachometer Hyperion Multi-pala
1 x Brass control horn M4 long for wire (4 pcs)
1 x Porta Kwik link M4 4 mm (2 pcs)
1 x Horn F3A de Titanium 16 mm (2 units)
1 x MVVS exhaust gasket 26cc
1 x Horn micro type4 Ø 0,5 (2 pcs)
1 x 6 mm aluminium horn with patella
1 x Turbina KINGTECH K70G4
1 x Fixing Ring with Base 40 mm
1 x Cylinder gasket ZG22 / ZG23 / G2D70 / G2D96-D
1 x Stainless Steel Bend D 20x0,6mm
1 x Gasket Carburetor-Insulator ZG22/23/26/ZG231/G2D96-D/G230R
1 x Gyro 3-Ejes REFLEX V2 FMS
1 x Servo Robbe FS 128 BB MG HV Digital
1 x Extra long Prop Bolt for ZG 45/62/74/80, with M5 threaded hole
1 x Servo AN-20 MGBBA
1 x SAVOX SH 1250 MG servo digi
1 x Profile ABS half cane 4x1000 mm
1 x Rubber profile 6-2 mm 2M
1 x 28 mm tailwheel unit
1 x Foreman, scale 1:32
2 x Profile ABS half cane 3x1000 mm
1 x Servo SAVOX SV-1270 TG
1 x Flap hinge 33x9 mm (6 pcs)
1 x Streamline Stainless Steel Tubing 6.3x3.5x1000 mm
1 x Brass hexagonal rod Ø 3 mm x 1000 mm
2 x Streamline Stainless Steel Tubing 19.5x9.8x1000 mm
1 x Brass hexagonal rod Ø 4 mm x 1000 mm
1 x Profile ABS half cane 2.0x1000 mm
1 x SAVOX SH 1290 MG servo digi
1 x Streamline Stainless Steel Tubing 11.5x6.5x1000 m
1 x Servoarm SH-81, two sides, aluminium
1 x Carbon fiber rod 5.0 mmx1000 mm
1 x ABS "T" angle 8.0x8.0x1000 mm
1 x L-Connector 1.0 mm x 1000 mm
1 x ALU double servo arm 3 mm shaft
2 x Profile ABS Square 3 x 1000 mm
2 x Profile ABS Square 2 x 1000 mm
1 x Decorative caps, multicoloured, short
2 x Streamline Stainless Steel Tubing 14.5x9.6x1000 mm
1 x Servo SAVOX SV-1260 MG
2 x L-Connector 1.5 mm x 1000 mm
1 x Profile ABS half cane 7.0x1000 mm
2 x U Profile ABS 8,0x4,0x1000 mm
1 x 40 mm 1/4" Race propeller (rigth hydropropeller)
1 x Streamline Stainless Steel Tubing 15.5x8.5x1000 mm
1 x ALU servo arm 90º 3 mm shaft
1 x Carbon tube (L 1000 mm, Ø4 mm, Ø2,5 mm)
1 x Servo SAVOX SA-1256 TG
1 x Profile ABS half cane 8.0x1000 mm
1 x Profile ABS triangular 6.0x1000 mm 90º
2 x L-Connector 4.0 mm x 1000 mm
1 x Charger LiPo Charger4
1 x ABS "T" angle 2.0x2.0x1000 mm
1 x Savox Highvoltage Brushless Servo SB-2272MG (Tail rotor)
1 x ABS angle 6,0x6,0x1000 mm
1 x Streamline Stainless Steel Tubing 10.5x5.7x1000 m
1 x Streamline Stainless Steel Tubing 7.5x4.5x1000 mm
1 x Servo SAVOX SB-2290 SG
1 x U Profile ABS 5,0x10,0x1000 mm
2 x Beech dowels 3.0 x 1000 mm
1 x Aluminium tube (L 1000 mm, Ø3.0 mm, Ø2.1 mm)
1 x Rubber profile 10-2 mm 2M
1 x Flat Connector 4.0 mm x 1000 mm
1 x Servo SAVOX SV-1273 TG
1 x Profile ABS half cane 4x2.5x1000 mm
1 x Cross Connector 4.0 mm x 1000 mm
1 x SAVOX SH 0254 servo
1 x Rubber profile 8-2 mm 2M
1 x Profile ABS triangular 2.0x1000 mm 90º
1 x Brass hexagonal rod Ø 3.5 mm x 1000 mm
1 x Servo mounting frame SV-1260MG
1 x Savox Brushless Servo SB-2271SG
1 x Brass rod Ø 1.0 mm x 1000 mm
1 x Profile ABS half cane 6.0x1000 mm
1 x Brass hexagonal rod Ø 5 mm x 1000 mm
1 x Servo SAVOX SV-1254 MG HiVolt Low Profile
1 x Brass rod Ø 0.8 mm x 1000 mm
1 x Carbon fiber rod 0.5 mmx1000 mm
1 x Balanceradapter JST-XH (Heli 47G) 2-6 c.
2 x Streamline Stainless Steel Tubing 12.3x7.7x1000 mm
1 x Beech dowels 4.0 x 1000 mm
1 x Propeller RF CFK 14.5x14
1 x Propeller RF CFK 13x7
1 x Propeller CFK 16x16 Wide
1 x Propeller CFK 15x7
1 x Propeller CFK 14x7
1 x Propeller CFK 18x9
1 x Propeller CFK 11x8
1 x Propeller CFK 14x10
1 x Motor DA 50-R
1 x Alu servo arm double RHINO
1 x Propeller RF CFK 10x17
1 x DA 70 Twin Gas Engine
1 x Propeller CFK 20x13
1 x Propeller CFK 15x15
1 x Propeller CFK 16x17
1 x Boxed KIT OF 7 Rotary Burrs FINE
1 x Pump hose (Ø 6/8 mm) transparent
1 x Set fresas corte Vanadium Ø 2.3/2.35 mm (3 pcs)
1 x Welder 100W/200V
1 x Tachometer HANGAR 9 digital
1 x Set fresas corte Vanadium Ø 2.3/2.35 mm (3 pcs)
1 x Fabric scissors curved (offset handles), 16 cm / 6" length
1 x 
1 x Fabric scissors curved Premium, 16 cm / 6" length
1 x silverlot 45% - 1,50x500 mm solder rods (2 pcs)
1 x 5 mm M2 variable horn
1 x OS GT15 W/E-4040 for airplane
1 x Micro clevis (10 uds)
1 x Pin 3,0 to cable coupler M3,0 ⌀ (6 pcs)
1 x Rear bearing for motor 35/40 cc
1 x Horn 16,5x20 mm (2 pcs)
1 x 6 mm M3 variable inclined horn
1 x Pulley brass 4/1,5 (2 pcs)
1 x Ø 1,6 mm pin for Kwik link MPJ2160/2161 (6 pcs)
1 x 6 mm M3 variable horn
1 x Duralumium F3A horn 30x10x23,5 mm (2 pcs)
1 x Kwik link aluminio IZD. M3 L: 30mm (2 uds) pin Ø 2 mm
1 x Cable control set
1 x MVVS presuritation conection 26-175 cc
1 x Brass control horn M4 short for wire (10pcs)
1 x Horn 5/10 with M2 Bearing
1 x Pulley brass 5/1,5 (2 pcs)
1 x Metal clevis M2,5 (10 uds)
1 x Horn with ball 40x30
1 x Extra-long adjustable aluminium control horn 2,8x34
1 x Pulley brass 14/2 (2 pcs)
1 x Kerostarter K30G
1 x Motor NGH GT-9 V2
1 x KingTech Turbineoil 1L
1 x GSU Kingtech
1 x Power Pack SE Series JETCENTRAL
1 x Electric starter BEE (old)
1 x BALSA trip 2.0x2.0x1000 mm
1 x Walnut wood slat 1.5x1.5x1000 mm
1 x Battery LiFe -2100/25C-3S 9.9V
1 x JETCENTRAL ECU LIFE BATTERY 3800 MAH
1 x Walnut wood slat 3.0x3.0x1000 mm
1 x BLUE Colored Liquid smoke for turbine 0.75 l
1 x Pine wood slat 6.0x6.0x1000 mm
1 x BALSA leading edge 8x10x1000 mm
1 x Trailing edge BALSA 35x8x1000 mm
1 x BALSA trip 10x10x1000 mm
1 x Pine wood slat 1.5x3.0x1000 mm
1 x Aro pasacable Ø25 mm (4 pcs)
1 x Propeller FOXY 34x12 2-Bl
1 x Walnut wood slat 2.0x2.0x1000 mm
1 x Propeller FALCON 5-BL 24x23.5
1 x DIVA cabin cruiser
1 x 20x15 Falcon electric V2
1 x Blade Holder (3 blades)
1 x Blade Holder Full (4 blades)
33,110.22EUR
Manufacturers
Manufacturer Info
Roi-Import
Roi-Import Homepage
Other products
Languages
Español English
Currencies