Top » Catalog » Hardware » Adhesives/Resin/Epoxy » Resin/Gelcoat » R1121250

11.00EUR

Hardener Aero EPH 161 (250 g)
[R1121250]

Hardener Aero EPH 161 (250 g)

Hardener for Epoxy Resin L and L 20, EP Gel coat colourless and Mould Resin P
Contains no formaldehyde and no paraformaldehyde
Epoxy Resin L
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by hot curing for: approx. 10 h at 60 °C
Max. heat distortion temperature after annealing: 120 °C
Laminate structures for vehicle construction in combination with this product and epoxy resin L are approved by the TÜV-Süd. Process instructions/TÜV-Report (unfortunately only in German)
Epoxy Resin L 20
The combination of L 20 and Hardener EPH 161 yields a low-viscosity laminating resin that exhibits superior impregnating and wetting properties to glass, aramid, and carbon fibres. In conjunction with L 20, hardener EPH 161 results in a long service life for the resin compound with very high mechanical and dynamic strengths and perfect curing in both thick (> 2 cm) and thin (1,5 mm) laminates. Before they can obtain the specified mechanical properties, the laminates must be post-cured for about fifteen hours at 60 °C after their initial cold-curing period.
The system L 20 + EPH 161 is approved for the construction of gliders.
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by post-curing: for 15 h at 60 °C
Gel coat colourless
Processing time: 90 minutes
Mixing ratio:
100 : 24 parts by weight EP Gel coat : Hardener EPH 161
Curing time: 24 h at room temperature, afterwards hot curing approx. 10 h/60 °C (recommended, but not necessary).
Max. heat distorsion temperature after annealing: approx. 120 °C
Mould resin P
Processing time: 90 minutes
Mixing ratio:
100 : 17 parts by weight Mould Resin P : Hardener EPH 161
Gelling time: approx. 4 h
Curing time: 24 h at roomtemperature, afterwards hot curing: approx. 15 h/60 °C
Please order resin L and L 20, gel coatcolourless and mould resin P separately

under request

Reviews

Categories

* OFFER MONTH *
Planes->
Sailplanes->
Autogyros->
Helicopters->
UAVs - RPAs->
Multicopters->
Hardware->

  3D IMPRESION
  ABS Rods-Strips
  ABS/GFK/CFK plate
  Actuator
  Adapters->
  Adhesives/Resin/Epoxy->
    Cianocrylate->
    Epoxy->
    Resin/Gelcoat
    Glass Bubbles
    Contact adhesive
  Altimeters->
  Amperimeters
  Anemometer
  Auto-Pilot
  Bags/Covers
  Batteries->
  BEC/Cables/Conectors/Interruptor
  Bungee Launchers
  Cables
  Cameras->
  Carbon rod
  Carbon/Brass/Steel/ABS/Aluminium
  Catalogues
  Chargers->
  Clevis
  Combustible->
  Connectors
  Control horns
  Controlers->
  Coverings/Thermoretrac
  Decals
  Extension
  Extinguisher
  Ferritas
  Glasses
  Hardware
  Hinges
  Instruments / Panels
  Lights/Ilumination->
  Linkages
  Merchandising
  Motor
  Pilots
  Pinion extractor
  Power supply system/Data Recordi->
  Profiles
  Propelers->
  Screws
  Servos->
  Simulators
  Smoke/Rocketry/Fireworks
  Spinners->
  Spray/Painting/Dope/Solder Paste
  Steel/brass Rod/Aluminium
  Support/CG/Incidenc.
  Tapes/Closed/Bridles
  Tools
  Towing
  Transmitters/Receivers->
  Undercarriage->
  Wheels & Axles->
  Wing Joiner
  Wood
Car/Trucks->
Motors & Turbines->
Gas. Motor Paramotors
Acces. for Motors->
Paragliders/Parachutes/Windsock
Boats/Naval units->
FPV->
Robots->
CNC cut
Roof BOX
Crash kits
Outlet Zone->
Used
Merchandising HA

What's New?

22x12 Falcon electric
105.00EUR

Information

Shipping & Returns
Privacy Notice
Conditions of Use
Financing
Point Program FAQ
Contact Us

We Accept

Quick Find

Shopping Cart

1 x	Epoxy Resin HT 2 + Hardener HT 2 (60 min) 1 kg
1 x	Mould Resin P + Hardener EPH 161-P, kit/ 585 g
1 x	Epoxy Resin L 285 + Hardener 285 (Aero), kit/ 1 kg
1 x	resin-hardener L-385 H-385 (625 g)
1 x	Hardener Aero EPH 161 (250 g)
1 x	MEKP Harderner 100 g
1 x	resin-hardener package L-385 with hardener H-385
1 x	Hardener Aero EPH 161 (500 g)
1 x	Threaded coupler ALU M2,5 Ø 4 (2 uds)
1 x	Clevis plastico I=44 mm / hole 3mm / pin 2 (2 pcs)
1 x	Z type of cable coupler Ø 1.8 (2 uds)
1 x	Ball link Aluminio M3 (6 uds) 27x11.9x5.9 mm
1 x	Threaded coupler ALU M3 Ø 4 (2 uds)
1 x	Threaded coupler ALU M2,5 Ø 3 (2 uds)
1 x	Couple M4 for wire (10 pcs)
1 x	Threaded coupler M2,5 Ø 2 mm (10 pcs)
1 x	Aluminium coupler M3/2 with ball bearing (1 pcs)
1 x	Threaded coupler M2,5 Ø 3 mm (10 pcs)
1 x	Ball Link ALU M3 - RH (1 pcs)
1 x	Threaded coupler ALU M3 Ø 6 (2 uds)
1 x	Threaded coupler M2 (10 uds)
1 x	Kwik link AL M3 con Clip (2 pcs)
1 x	Clevis plastico I=26 mm / hole 2mm / pin 1 (2 pcs)
1 x	Aluminium coupler M2/2 with ball bearing (1 pcs)
1 x	Threaded coupler ALU M2,5 Ø 6 (2 uds)
1 x	Aluminium blue ball links M3 V1 (10 pcs)
1 x	Brass ball links BS M3 V1 (10 pcs)
1 x	Crimping sleeves for 1.1 mm cable (10 pcs)
1 x	Threaded coupler ALU M3 Ø 5 (2 uds)
1 x	Threaded coupler Micro M2 Ø 0,8 mm (10 pcs)
1 x	Threaded coupler ALU M2 Ø 4 (2 uds)
1 x	LASER 73" 1.85m (05) PILOT
1 x	Propeller POWER-PROP 13x9 Izda
1 x	Propeller POWER-PROP 13x9
1 x	Sandwich carbon + poplar 4mm + carbon 480x290 mm
1 x	FALCON 20X9 CARBON PROPELLER (GAS)
1 x	20 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	RUDDOG Protection and Heat Shield Tape (2mx50mm)
2 x	Propeller POWER-PROP 14x9
1 x	SE Ring 450 mm (2 pcs)
1 x	Ring 320 mm length (5 pcs)
1 x	Tape GFK 50 mm
1 x	SE Ring HACKER 300 mm (2 pcs)
1 x	PIX Hawk with accesories
1 x	PPM Encoder Module
1 x	Digital Air Speed Sensor And Pitot Tube Set
1 x	Tube Pitot to PIXHAWK
1 x	Camera Sony 4140+673 CCD with Built-in 200mw TX + antenna
2 x	USB Mini Camera endoscope
1 x	800TVL CMOS camera for FPV
1 x	PARTALL® Hi-Temp Wax, 340 g
1 x	Extinguisher CO2 - 2 Kg
1 x	Cable S.BUS 3 salidas 100 mm
1 x	Cable silicona macho batt. receptor 30 cm (Futaba)
1 x	ABS tube 9.0x7.0x1000 mm
1 x	Horn 6/35 with M3 Bearing
1 x	White smoke canister 65 g
1 x	Ball link M3 RPA's-UAV's
1 x	M3 Maxi ball link (2 uds)
1 x	Truck-trailer for gliders 720 x 239 mm
1 x	Wire easy tensioner (red)
1 x	Turnbuckle M3 33x49 (2pcs)
1 x	Small kwik link (10 pcs)
1 x	resin-hardener L-385 H-385 (1250 g)
1 x	P 17×5.8 Prop-2PCS/PAIR
1 x	Ball Link M2 with Ball and Hardware, 10 pcs
1 x	Landing gear Rocket 400
1 x	1804 2400KV Brushless Motor Qav 250 mini
1 x	Epoxy Resin L 285 + Hardener 386, kit/ 1.35 kg
1 x	Mobile Terminal
2 x	Zurich Sport Sunglasse Dark Sensity BROWN Glasses
1 x	Angled clevis with threaded rod M3
1 x	Oracover GREY Seafire Sea 2m
1 x	Servo Arm 25T M3 KAVAN 6.5 / 19.6 mm
1 x	Motor KAVAN PRO 2225-1600
1 x	Waterproof adhesive tape, width 19mm, length 25m
1 x	Prop Holder AXI 41xx V2
1 x	DJI Mavic Air Fly More Combo
1 x	Helices DJI Mavic Air STEALTH "Black" (4x Ud)
1 x	3.17 mm Prop Adapter CN-Spinner
1 x	2.3 mm Adapter for 30 mm spinners
1 x	10x7 tree blades propeller
1 x	15x7 tree blades propeller LEFT
1 x	10 mm Prop Adapter M12
1 x	25,0 mm 3-BL M4 hydro-propeller (rigth hydropropeller)
1 x	3 mm Prop Adapter M6
1 x	16x10 tree blades propeller Master Airscrew
1 x	10 mm portholes (10 pcs)
1 x	3,2 mm Prop Adapter M6
1 x	Motor A20-26 M EVO
1 x	Shaft for A60-20/22/24S (120 mm)
1 x	OS Engine 105HZ-R Heli with pipe 105
1 x	Motor OS 3820-1200 electric
1 x	MIG AC 400 /14
1 x	OS Engine 105HZ-R Heli
1 x	XPower XC4226/12 LS
1 x	Propeller electric carbon 10x8
1 x	ABS angle 2,0x2,0x1000 mm
1 x	ABS Strip 1.5x8.0x1000 mm
1 x	White smoke bombs AX-3 (10 pcs)
1 x	White smoke bombs AX-18 (5 pcs)
1 x	Size "L" motor holder for class 600
1 x	Actuador lineal HLS12-100210-7.4v
1 x	KIRA 600-22 6,7:1
1 x	KIRA 600-20 6,7:1
1 x	Motor B20-18 L + 4:1 gearbox
1 x	Motor A60-6XS V4 28-pole kv370
1 x	Shaft for A60-L (140mm)
1 x	Dumper propeller 6/8 mm
1 x	Parachute expulsion foam
1 x	ABS Strip 1.0x5.0x1000 mm
1 x	ABS "T" angle 8.0x8.0x1000 mm
1 x	290x4 mm M4 shaft ship
1 x	B4-0 rocket charges (6 pcs)
1 x	ABS Strip 1.0x2.0x1000 mm
1 x	ABS tube 14.0x10.0x1000 mm
1 x	Rocket D9-7
1 x	ABS tube 3.0x1.0x1000 mm
1 x	ABS angle 5,0x5,0x1000 mm
1 x	ABS rectangular profile 12x6.0x1000 mm
1 x	ABS tube 2.0x1.0x1000 mm
1 x	ABS Strip 1.5x6.0x1000 mm
1 x	Red smoke bombs AX-60 (5 pcs)
1 x	AX-60 starters (5 pcs)
1 x	ABS Strip 1.5x2.0x1000 mm
1 x	261 mm M4/M4 6.0x4.0 mm shaft ship
2 x	ABS "T" angle 6.0x6.0x1000 mm
1 x	Glases Stratus
1 x	Glases Moritz
1 x	Glases Innovation Plus
1 x	Glases Ace
1 x	Glases Nimbus
1 x	Receiver bed (Blue)
1 x	Size "M" motor holder for class 600
1 x	Ø 40 mm fiberglass motor-holder for electric motors
1 x	Central support Speed 280
2 x	Cable video GoPro
2 x	Propeller CFK 12.5x6.5
2 x	Propeller CFK 23x12
1 x	Propeller CFK 18x16
1 x	ABS I Strip 20x10x1000 mm
1 x	120x60 mm SLH KOVO wheel
1 x	ABS tube 18.0x16.0x1000 mm
1 x	Propeller CFK 15.5x10
1 x	AX-60 starters (5 pcs)
1 x	Propeller CFK 20x13
1 x	Propeller CFK 14x8
1 x	Propeller RF CFK 10x17
1 x	Propeller CFK 15x15
1 x	Propeller CFK 15x7
1 x	Propeller RF CFK 14.5x14
1 x	Propeller CFK 13x7.5
1 x	Propeller CFK 15x13
1 x	Propeller RF CFK 13x6.5
1 x	Propeller CFK 12.5x7
1 x	Propeller CFK 14x6.5
1 x	Propeller CFK 18x9
1 x	Propeller CFK 13x9
1 x	Propeller CFK 17x18
1 x	Propeller CFK 14x7
1 x	Propeller CFK 16x17
1 x	Propeller CFK 15x16
1 x	Propeller CFK 17x13
1 x	Propeller CFK 12.75x13
1 x	Propeller CFK 11x8
1 x	Propeller CFK 14x10
1 x	Propeller CFK 16x16 Slim
1 x	Propeller RF CFK 16x8,5 S
1 x	Propeller CFK 15x13 Slim
1 x	Propeller CFK 12X6
1 x	Propeller CFK 14x8 Slim

8,224.41EUR