130.00EUR

Eachine EV800D 5 Inches 800x480 FPV VR Goggles Monitor
[ROIEV800D]


Gafas FPV Eachine EV800D

Dimension: 180*145*82mm
Weight: 362g without antenna
Belt : three-way adjustable belt

Specification
Build in DVR
Record up to 720*576px full frame rate video, no frame lost (C10 card required)
Replay in MENU
Require C10 card to record full frame rate
Diversity Super sensitiveness in 2pcs RX5808 PRO modules
Great performance when two types (Linear and Omni) antennas are used
Display Screen size: 5.0 inch
Screen resolution: 800*480(No blur after enlarge by the lens)
Screen brightness: 600cd/m2 with special high brightness backlight LED for outdoor FPV
View Angle: 140/120 degree(Horizontal/Vertical)
Lens 3x boost of the video to acquire intense feel-in-there video; 92% transparent rate distort if light;
Battery Built-in 7.4V/1200mAh battery;
Each battery circle offer around 2hr working time;
11-20V wide range recharging voltage range, typical recharging voltage is 12V 2S (7.4 V) /3S(11.1V) battery as back-up power t to have long working time.
Frequencies (5.8GHz, with RaceBand)
CH CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8
GROUP A or FR1 5865 MHZ 5845 MHZ 5825 MHZ 5805 MHZ 5785 MHZ 5765 MHZ 5745 MHZ 5725 MHZ
B or FR2 5733 MHZ 5752 MHZ 5771 MHZ 5790 MHZ 5809 MHZ 5828 MHZ 5847 MHZ 5866 MHZ
C or FR3 5705 MHZ 5685 MHZ 5665 MHZ 5645 MHZ 5885 MHZ 5905 MHZ 5925 MHZ 5945 MHZ
D or FR4 5740 MHZ 5760 MHZ 5780 MHZ 5800 MHZ 5820 MHZ 5840 MHZ 5860 MHZ 5880 MHZ
R or FR5 5658 MHZ 5695 MHZ 5732 MHZ 5769 MHZ 5806 MHZ 5843 MHZ 5880 MHZ 5917 MHZ

Features:
Built-in with super HD DVR record up to 720*576px resolution
Diversity RaceBand 40ch Auto-Searching
Two system (Display/Record duo core separated chipsets ) ensure no delay in displaying and no frame lost in recording(please use C10 super speed card to ensure the full frame recording)
Work friendly with pilot-OSD, no block on the important flying OSD information; Separable design, 5 inch screen can be used as small monitor on radio controller or with tripod;
HD high brightness 5 inch LCD specially tuned for FPV racing;
Diversity function, Built-in super sensitive 5.8GHz 40ch receiver module, with RaceRand;
Advanced auto-searching function and the working frequency show on screen;
Built-in 7.4V 1200mAh battery, each full charge offer 2 hours working time;
Wide range re-charge voltage 11-20V;
Accept 2S or 3S batteries as back-up power source, to prolong the working time; Nice ergonomic design and fit different faces;
Super-wide visible angle up to 82 degree;
92% transparent lens adopted, no distort, no blur on the edge of screen;
Light weight 375g with 3.5 hr 2000mAh battery, RTF for any scale racing game;
5 Inch 800*480px HD high brightness LCD

Package Included :
+ 1 x Eachine EV800D
+ 1 x Charger
+ 1 x 5.8G halfplanner antenna with RP-SMA connector
+ 1 x 5.8G RHCP cloverleaf antenna with RP-SMA connector
+ 1 x AVin cable
+ 1 x DCpower cabler to 3S balancer plug cable
+ 1 x Fresnel lens clearning kit
+ 1 x Instruction manual (English)


few units
few units

Reviews
We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x Propeller balancer
1 x GameCommander USB Universal
1 x Interface Realflight Simulator
1 x Silicone 0,50 qmm servos wire Futaba (100 m)
2 x Cable servo PREMIUM MAXI 100m (blanco/rojo/azul) PVC
1 x EasyFLY Addon
1 x Long ball link M1.6 (6 uds)
1 x Plasti Dip Liquid Tape 429 ml black
1 x Universal Colour Paste white 50 g
1 x Stickers-digit for marking
1 x Adapter lead MPX/EC3
1 x Aluminium rod Ø 4.0 mm x 3000 mm
1 x MPX-Dean "T" Adapter
1 x Strip 3,5x1,75x330 mm
1 x Receiver Hitec OPTIMA 9 2.4 GHz AFHSS 9ch
1 x PPM Encoder Module
1 x Carbon wing joinner 13,4 mm Ø 0,48 mm
1 x Ball link M3 RPA's-UAV's
1 x PROXXON - SANDING BELTS FOR BSL 220/E 180 GRIT (5 pcs)
1 x M2 5Diam black ball link V2 (2 pcs)
1 x DUPLEX R12 EPC receiver 2,4GHz
1 x M3 Maxi ball link (2 uds)
1 x Ball link M1.6 (6 uds)
1 x ABS Strip 1.0x3.0x1000 mm
1 x Carbon fiber rod 0.5 mmx1000 mm
1 x Brass rod Ø 1.5 mm x 1000 mm
1 x Socket head long ball link M3 (2 uds)
1 x Round Rod 1,0x1000 mm
1 x Paint gun for sprays
1 x PROXXON - SILICON CARBIDE BELTS FOR BSL 220/E
1 x Stainless steel cable Ø 0.62 mm (10 m)
1 x 67 mm cylidric hinge Ø 5 mm (4 pcs)
1 x Ball Link Plier
1 x Locking cable tie 4.6x203 (uds)
1 x AX-60 starters (5 pcs)
1 x 20 g tin paste
1 x Mahogany wood slat 2.0x2.0x1000 mm
1 x BEC 3A FOXY
1 x DUPLEX R12 receiver REX Assist
1 x Screwdriver for Hexagon 1,27mm
1 x BALSA trip 8.0x8.0x1000 mm
1 x 12V Car Adapter
1 x Copier 2x20 cm pcs
1 x 3,0x60 mm allen screwdriver
1 x Straightened rod Ø 5.5 mm x 1000 mm
1 x Sun Cover BULL Mo1 2.6 (Hispano Aviacion)
1 x Hot Glue Stick RED
1 x DUPLEX RC Droid Box - DC/DS
1 x BlueCom™ Adapter (Android / WP)
1 x MRPM-AC revolution sensor
1 x M3 INDUSTRIAL ball link (2 uds)
1 x Receiver DUPLEX R9 EX 2.4 GHz
1 x Long pinned hinge (6 uds)
1 x Pine wood slat 2.0x2.0x1000 mm
1 x Straightened threaded rod M2-1m
1 x Carbon fiber rod 6.0 mmx1000 mm
1 x Maleta transporte FUTABA 10PX
1 x Vacuum bag, 1200 mm x 50 m
1 x Battery FUTABA 18MZ
1 x Extension silicon 35 cm male (Futaba)
1 x 1/4 Pilot "Heidi"
1 x Carbon fabric 200 g/m² (Aero, plain weave) 100 cm x 5m
1 x Carbon fabric 160 g/m² (plain weave) 100 cm x 3 m
1 x U Profile ABS 8,0x4,0x1000 mm
1 x Glass fabric tape 225 g/m² (Silane, plain) 30 mm X 100m
1 x Transmitter Balancer Futaba T-10CG
1 x 1/10 Pilot "Jimmy"
1 x Xplorer4 anemometro
1 x CNC FPV Display screen&Transmitter Holder Vertical
1 x Contest-S-Pult-Carbon mc-20/mc-24
2 x Cable servo PREMIUM MAXI 1 m (blanco/rojo/azul) PVC
1 x 50m servo "Premium" wire (white/red/blue)
1 x PVC 0,08 qmm Futaba servos wire (5 m)
1 x SIMtransmitter 6 Mode 2
1 x Cable servo PREMIUM MAXI 50m (blanco/rojo/azul) PVC
1 x Interface Jack Adapter IKARUS
1 x Vacuum pump P1-N
1 x Straightened rod Ø 3.0 mm x 1000 mm
2 x 5 line servos wire black (1 m)
1 x Carbon rectangular rod 3.0 mm x 1.0 x 1000 mm
1 x Receptor MINIMA 6S HITEC
1 x Extension for SensorSwitch 60cm
1 x Nylon hinge 20x15x0,3 (10 pcs)
1 x Fast'n EZ-CA-Hinge, lite (12 uds)
1 x Universal Colour Paste deep black 50 g
1 x Carbon fiber flat 1000x3.0x1.0 mm
2 x Cable servo PREMIUM MAXI 10m (blanco/rojo/azul) PVC
1 x 2,0x50 mm allen screwdriver
1 x Straightened rod Ø 4.5 mm x 1000 mm
1 x Straightened rod Ø 14.0 mm x 1000 mm
1 x Carbon fiber rod 12 mm x 1000 mm
1 x Flap hinge (6 pcs)
1 x Ball link M2 (10 pcs)
1 x Hobbylite Filler, Balsa colour
1 x Pin type hinge Al 4,5x70 mm to wire (2 pcs)
1 x Optical RPM Sensor
1 x Black smoke bombs AX-60 (5 pcs)
1 x Unmounted aluminium pin 6x98 mm (2 pcs)
1 x Straightened rod Ø 1.5 mm x 1500 mm
1 x ABS Strip 1.0x4.0x1000 mm
1 x "Y" charging 4mm wire (2 IN-1 OUT).
1 x Ball link M3 (10 pcs, flat ball)
1 x Circlik for shaft 1.2 mm (10 pcs)
1 x ABS angle 4,0x4,0x1000 mm
1 x 1/4 Pilot "Mike"
1 x SE Ring 300 mm (2 pcs)
1 x Receptor FUTABA R7003SB FASST
1 x Tray for FUTABA 14SG/16SZ
1 x SE Ring 240 mm (2 pcs)
1 x Premium servo extension 100cm
1 x 1/12 Pilot "Cougar"
1 x Carbon Non-Woven, 160 g/m² 127 cm 1 m
1 x AIREX® Sheets C 70.55 (YELLOW) 1200x550x1.2 mm (5 pcs)
1 x Futaba R7114SB 2.4GHz FASTT/FASSTest S.BUS Receiver
1 x Receiver bed (Blue)
1 x Tape GFK 25 mm
1 x Circlik for shaft 1.5 mm (10 pcs)
1 x TX 250 mW especial GOPRO
1 x Antenna FUTABA 2.4GHz 3PM/8FG/14SG/18SZ/18M
1 x Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 20 m
1 x Circlik for shaft 2.3 mm (10 pcs)
1 x SE Ring 400 mm (2 pcs)
1 x Aluminium wide washer M3 blue (4 pcs)
1 x Extension S-Bus 1-2 silicon 30 cm FUTABA
1 x Aluminium cap bolt washer M4 blue (8 pcs)
1 x Aluminium wide washer M4 Red (4 pcs)
1 x 10 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x Fibra carbono 3k tela 160g/m2 100 cm x 5m
1 x Profile ABS Square 2 x 1000 mm
1 x Medidor ángulos y/o incidencias
1 x Battery voltage telemetry
1 x WingFix ULTRA Black Edition
1 x OSD Telemetry sensor
1 x Truck-trailer for gliders 720 x 285 mm
1 x Angle of incidence meter
1 x Field folding model stand
1 x Field folding model stand SebArt
1 x Cabel PVC 2 x 0.25 mm2 (5 m) red-black
1 x JR silicone servo wire 0,35 qmm / 5m
1 x Green silicone 0,25 qmm wire (50 m)
1 x Silicone red 0,25 mm² wire (25 m)
1 x Silicone 0,14 qmm servos wire Graupner (5 m)
1 x PVC 0,14 qmm servos wire JR/Graupner (5 m)
1 x Cable Cargador FUTABA
1 x Simulador RealFlight RF-9.5 S (sin emisora)
1 x Silicone 0,14 qmm servos wire Graupner (100 m)
1 x PVC 0,14 qmm servos wire Hitec/Mpx (5 m)
1 x PVC 0,08 qmm Graupner servos wire (5 m)
1 x Silicone 0,25 qmm servos wire Graupner (5 m)
1 x PVC 0,35 qmm servos wire Graupner (100 m)
1 x 100m servo "Premium" wire (white/red/blue)
1 x Silicone 0,35 qmm servos cable Futaba (5 m)
2 x 1 m servo "Premium" wire (white/red/blue)
1 x Silicone 0,35 qmm servos wire Futaba (100 m)
1 x Silicone 0,50 qmm servos wire Graupner(5 m)
1 x White silicone 0,25 qmm wire (100 m)
1 x 10m servo "Premium" wire (white/red/blue)
1 x Silicone 0,35 qmm servos wire Graupner(100 m)
1 x White silicone 0,25 qmm wire (150 m)
1 x 3l Smoke oil
1 x SUS wire 3m (nylon coated)
1 x Spray YELLOW Inca Lexan 150ml
1 x DUPLEX 2,4GHz MRPM EX
1 x Sensor DUPLEX 2.4EX MUI 200
1 x M2,5 5Diam black ball link V2 (2 pcs)
1 x Hot Glue Stick GREEN
1 x JETImodel SINGLE BEC
1 x Spray Graphit 33
1 x BALSA trip 3.0x3.0x1000 mm
1 x DUPLEX 2.4EX MU 3 Sensor
1 x CC 05
1 x Dean "T" - Futaba Adapter
1 x Digital Air Speed Sensor And Pitot Tube Set
1 x ABS I Strip 10x5x1000 mm
1 x Gates hinge
1 x Carbon fiber rod 20 mmx1000 mm
1 x ABS I Strip 20x10x1000 mm
1 x JETImodel Addcap 820
1 x Pin type hinge Al 4,5x70 mm demount (2 pcs)
1 x Straightened rod Ø 6.0 mm x 1000 mm
1 x Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm)
1 x Walnut wood slat 2.0x2.0x1000 mm
1 x Painting GHT Lexan Black 150 ml
1 x Strip ABS 2.0x3.0x1000 mm
1 x 6 mm hexagonal ball link M3 (10 pcs)
1 x Stainless steel cable Ø 0.5 mm (20 m)
1 x M2/M1/6 3Diam long black ball link V1 (2 pcs)
1 x White smoke canister 140 g
1 x Straightened rod Ø 1.2 mm x 1500 mm
1 x DUPLEX R10 receiver 2,4GHz
1 x Receiver DUPLEX R5L EX 2.4 GHz
1 x 30 cm BEC cable (female)
1 x M2,5 / 5Diam metal short ball link V3 (2 pcs)
1 x Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm)
1 x Conector JR Servo male (10 pcs)
1 x Red copper lacquer wire Ø0,2 mm (5 m)
1 x Strip ABS 2.0x10.0x1000 mm
1 x USB HLS prog. interface
1 x DUPLEX 2.4EX MAlti (Rev.2)
1 x Short ball link M3 (6 uds)
1 x Pine wood slat 6.0x6.0x1000 mm
1 x Steering arm 12 mm Ø 4 mm
1 x DUPLEX 2.4EX MSpeed PITOT <300 Km/h
1 x M2/M1/6 3Diam short black ball link V1 (6 pcs)
1 x "S" set for planes
1 x Linden wood slat 2.0x2.0x1000 mm
1 x 6 mm ball link M3 (10 pcs)
1 x Receiver DUPLEX R4H EX 2.4 GHz
1 x Tube Pitot to PIXHAWK
1 x Carbon fiber rod 1.0 mm x 1000 mm
1 x Gates hinge 30x16 mm (2 pcs)
1 x Spray EC Red 400ml
1 x Carbon fiber flat 1000x6.0x0.8 mm
1 x Circlick securite
1 x OPTIC 8 opto Rx-servo insulation
1 x Screwdriver for Torx® TX6
1 x TP/TopFuel - JST-EH 4/5S Adapter
1 x Strip ABS 2.0x8.0x1000 mm
1 x Short ball link M1.6 (6 uds)
1 x Cockpit plastic closing
1 x Nylon hinge for flaps/gates 27x10,5 (2 pcs)
1 x Stainless steel cable Ø 0.5 mm (2 m)
1 x Carbon fiber rod 0.5 mmx1000 mm
1 x BALSA triangular 8x8x1000 mm
1 x BALSA triangular 10x10x1000 mm
1 x Battery charging cable XT60
1 x Joint with bearing M3 22x5,5
1 x Carbon fiber rod 7.0 mmx1000 mm
1 x Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH
1 x Yellow smoke canister 100 g
1 x Pine wood slat 3.0x7.0x1000 mm
1 x 2 LiPo XH>EH adapter
1 x Straightened rod Ø 8.0 mm x 1000 mm
1 x Carbon fiber flat 1000x3.0x0.5 mm
1 x Starter EM Gear Power 250
1 x BlueCom™ Adapter (iOS)
1 x M2/M1/6 3Diam long black ball link V1 (6 pcs)
1 x Brass hexagonal rod Ø 3.5 mm x 1000 mm
1 x Crimping sleeves for cable 0.85 mm (10 pcs)
1 x Stainless steel cable Ø 0.5 mm (10 m)
1 x Receiver DUPLEX R3L EX 2.4 GHz
1 x BALSA triangular 6x6x1000 mm
1 x Futaba External voltage input cable Futaba CA-RVIN-700
1 x Large flex hinge (12 uds)
1 x CC 01
1 x CC 03
1 x White smoke bombs AX-9 (10 pcs)
1 x Locking cable tie 3.2x142 (uds)
1 x ABS Strip 1.5x4.0x1000 mm
1 x ABS Strip 1.5x6.0x1000 mm
1 x BALSA leading edge 8x10x1000 mm
1 x Covered closure or fairings
1 x White smoke bombs AX-3 (10 pcs)
1 x Cut tube
1 x Digital scale up to 40 kg
1 x DUPLEX 2.4EX MULi 6s M
1 x Straightened rod Ø 5.0 mm x 1000 mm
1 x M2,5 Diam metal short ball link V3 (2 pcs)
1 x 3 copper lacquer wire Ø0,2 mm (1 m)
1 x Carbon rectangular rod 10.0 mm x 1.0 x 1000 mm
1 x Canopy Latch
1 x Electric spoiler 250 mm (2 pcs)
1 x "M" set
1 x Starter Sullivan-STAR 603 DINATRON
1 x Green smoke canister 140 g
1 x Round Rod 2,0x1000 mm
1 x White smoke canister 100 g
1 x AddCAP 10AS capacitors
1 x DUPLEX MUI 50 Sensor
1 x Vacuum pump 12 CFM
1 x Spray adhesive INFUTAC (Clear) 500 ml
1 x DUPLEX R10 receiver REX Assist
1 x DUPLEX 2.4GHz GPS
1 x Dust collector for mould cleaning
1 x Brass hexagonal rod Ø 4 mm x 1000 mm
1 x Smoke set "Glider"
1 x Cierre cabina aluminio Ø4, I=10 mm
1 x DUPLEX 2.4EX MUI 75
1 x 
1 x 76 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs)
1 x Red smoke canister 100 g
1 x Long pinned hinge (12 uds)
1 x DUPLEX MUI 30 Sensor
1 x Strip ABS 2.0x5.0x1000 mm
1 x M2,5 5Diam metal ball link V3 (2 pcs)
1 x Starter 12v (Max 180 and 30ccm)
1 x Beech dowels 4.0 x 1000 mm
1 x ABS Strip 1.0x5.0x1000 mm
1 x Multiplex True Air Speed + Vario Sensor to M-LINK
1 x Wingstabi 9 DR M-Link Receiver
1 x Small pinned hinge (12 uds)
1 x Yellow smoke bombs AX-60 (5 pcs)
1 x Suport PITOT
1 x 5 LiPo XH>EH adapter
1 x Pin type hinge Al 3,0x50 mm (2 pcs)
1 x Mahogany wood slat 1.5x1.5x1000 mm
1 x Hexagonal ball head 2.0 x 50 mm
1 x Disposable Injector Bags (30x16cm) 100 pcs
1 x DUPLEX 2.4 EX MBar
1 x Extension for SensorSwitch 30cm
1 x Squared carbon wing joinner 5x5x220 mm
1 x Crimping tool
1 x Pine wood slat 3.0x10.0x1000 mm
1 x DUPLEX USB Adapter
1 x M2 5Diam short black ball link V2 (2 pcs)
1 x ABS Strip 1.5x8.0x1000 mm
1 x M3 Maxi ball link (2 uds)
1 x Cap closure 33/23.5mm (2 uds)
1 x M2,5 Diam metal ball link V3 (2 pcs)
1 x DUPLEX 2.4EX Satellite receiver Rsat 2
1 x Yellow smoke canister 140 g
1 x 25 mm reinforced hinge
1 x Cierre cabina aluminio Ø5, I=16 mm
1 x Steering arm 12 mm Ø 4 mm (2 uds)
1 x Steering arm 16 mm Ø 4 mm
1 x PowerBox Smokepump JETs 2x outside
1 x DUPLEX 2.4EX RC Power Switch 10
1 x Pitot tube JETI MSpeed DUPLEX
1 x Copper lacquer wire Ø0,2 mm (5 m)
1 x CellPRO 4S Adaptader (GP/KO up to 4S)
1 x Cable set PREMIUM Maxi, SUB-Done 4three fuselage/wing 200 cm
1 x MT 125 temperature sensor
1 x Cylidric hinge 33 mm Ø 2 mm (5 pcs)
1 x 67 mm cylidric hinge Ø 4,5 mm (5 pcs)
1 x L cockpit anchor "tipe F3A" (2 pcs)
1 x 67 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs)
1 x 48 x 10 mm cylidric hinge Ø 3,0 mm (10 pcs)
1 x Nylon hinge 20x20x0,3 (10 pcs)
1 x Socket head ball link M3 (2 uds)
1 x Sensor DUPLEX 2.4EX MUI 200 MULi 6S for measuring voltage on LiX
1 x DUPLEX R6G indoor receiver 2,4GHz
1 x Universal Colour Paste deep black 250 g
1 x Carbon fiber rod 4.0 mmx1000 mm
1 x Round Rod 1,25x1000 mm
1 x Pine wood slat 10x10x1000 mm
1 x Transmitter Balancer SPK DX-8
1 x Spring lock washer 4.1 mm (20 pcs)
1 x Pilot "Goose" (Slimline)
1 x Fibra carbono tela 160g/m2 100 cm x 2 m (twill weave)
1 x Ant. Cable R606/17/08/14FS L:1500mm
1 x Quicklock washer 4 mm (10 pcs)
1 x Cable S.BUS 3 salidas 100 mm
1 x SE Ring 480 mm (2 pcs)
1 x Carbon fibre tape 200 g/m² (unidirectional) 50 mm
1 x Switch Cap L (silver)
1 x Cable silicona macho batt. receptor 30 cm (Futaba)
1 x Interruptor FUTABA FX-MZ (2 Posic. corto)
1 x U Profile ABS 5,0x10,0x1000 mm
1 x PT 21x13 EL Propeller
1 x Cabel "Y" 30 cm (Futaba)
1 x Extension 90 cm (Futaba)
1 x Foil for sticking flaps and ailerons
1 x Ring 320 mm length (5 pcs)
1 x 1/6 Pilot "Cindy"
1 x Quicklock washer 2.5 mm (10 pcs)
1 x 1/12 Pilot "Fighter"
1 x Charger FUTABA SQN30W12P-08 220v
1 x Decorative caps, multicoloured
1 x Spring lock washer 2.1 mm (20 pcs)
1 x SE Ring 250 mm (2 pcs)
1 x Aluminium wide washer M4 Gold (4 pcs)
1 x Switch Cap L (Blue)
1 x Extension silicon 10 cm (Futaba)
1 x Tape GFK 38 mm
1 x RUDDOG Protection and Heat Shield Tape (2mx50mm)
1 x 13 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x Streamline Stainless Steel Tubing 12.3x7.7x1000 mm
1 x 1/6 Pilot "Garry"
1 x Carbon Non-Woven, 160 g/m² 100 cm 25 m
1 x Extension 30 cm (Futaba)
1 x Waterproof adhesive tape, width 19mm, length 25m
1 x Carbon fabric 160 g/m² (twill weave) 127 cm, roll/ 10 m
1 x Extension silicon 30 cm female (Futaba)
1 x Futaba R3008SB T-FHSS 2.4GHz S.Bus2 8/32 Channel Receiver
1 x VBar Control RX-Satellite
1 x 20 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x 
1 x Glass fabric tape 225 g/m² (Silane, plain) 40 mm
1 x Flat washer 4.3 mm (20 pcs)
1 x Receiver FUTABA R7014SB FASST Test
1 x Ventus 1:4 set of instruments
1 x Lock washer 2.2 mm (20 pcs)
1 x Streamline Stainless Steel Tubing 9.0x5.0x1000 mm
1 x MULTIPLEX ALUMINUM CASE "M-LINK"
1 x Extension lead 15 cm Multiplex
1 x Flat washer 3.2 mm (20 pcs)
1 x ABS angle 2,0x2,0x1000 mm
1 x Piloto Jet "Green" 1/6 Scale
1 x Futaba Female 40 cm extension
1 x Carbon Non-Woven, 160 g/m² 127 cm 5m
1 x Extension silicon 100 cm (Futaba)
1 x ABS angle 3,0x3,0x1000 mm
1 x Xplorer1 anemometro
1 x Streamline Stainless Steel Tubing 10.5x5.7x1000 m
1 x Receptor FUTABA R7208SB FASSTest SBus2
1 x Streamline Stainless Steel Tubing 6.3x3.5x1000 mm
1 x Streamline Stainless Steel Tubing 11.5x6.5x1000 m
1 x 20x1000 mm Ring Strap Back To Back
1 x Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 10 m
1 x Civilian pilot "Curt" size 9cm (Slimline)
1 x ABS "T" angle 8.0x8.0x1000 mm
1 x Antena FUTABA receptor Standard 2.4 GHz ( 200 mm aprox.)
1 x Flat washer 2.2 mm (20 pcs)
1 x Switch Cap M (blue)
1 x Lock washer 2.7 mm (20 pcs)
1 x Extension PVC 150 cm (Graupner)
15,100.06EUR
Manufacturers
Manufacturer Info
Roi-Import
Roi-Import Homepage
Other products
Languages
Español English
Currencies