54.24EUR

NF-3 RC set
[NF-3RC Set]



Funcionamiento del NF-3

Esquema de conexi�n
NF-3RC extends the capabilities of the NF-2RC unit with a greater number of circuits and more flash lights regimes. Just as NF-2RC it has two position lights circuits. It has also two landing lights circuits and two flash light circuits. Switching on/off of the second landing lights circuit is delayed by 1 second against he first circuit. That produces an effect of phased switching by the pilot. Eight different combinations of flashing can be selected for the two flash light circuits. Three couplers (jumpers) are used for selection.

One second is split into 16 parts. It is possible to set during which parts the light should be on (1) and off (0) to both flash circuits. Such a couple of sequences of 16 ones and zeros represents one combination of flashes. Eight such combinations (couples of sequences) are saved in the unit. By default, the unit contains six combinations of 1, 2 and three mutually shifted flashes plus two flashing modes 1:1, one with the period 1s, the other twice faster. The last two regimes are designed especially for helicopters owners.

A coupler is used for selection of 2- and 3-positional control regime as in NF-2RC. If the 2-position control is selected, in the first position the position and ant-collision lights light, in the second position the landing lights get switched on, too. In the three-position regime, in the first position, all lights are off, in the second position the position lights and anti-collision flash lights are on and in the third position, all lights are on. The unit can be used also in no-control mode. In that mode, position and flash lights are permanently turned on and the coupler for regime selection switches the landing lights.

Thanks to a galvanic separation of the receiver’s and power circuits (by an opto-member), the illumination can be powered both from a common source or from an independent accumulator. The NF-3RC unit can be used also as a basis for your own constructions for excitation of MOSFET power transistors.

The circuit is extended with detection of failure of the receiver's signal - it is indicated by permanent flashing of the anti-collision flash lights and the landing lights.

The NF-3RC, besides control circuit, includes 1x5 mm 20 mAh green LED, 2x5 mm 20 mAh red LEDs and 6x5 mm 20 mAh white LEDs


temporarily out of stock
temporarily out of stock

Reviews

Customers who bought this product also purchased
NF-1 RC set
NF-1 RC set

temporarily out of stock
temporarily out of stock

Connectors MPX female
Connectors MPX female

temporarily out of stock
temporarily out of stock

Connectors MPX male
Connectors MPX male

temporarily out of stock
temporarily out of stock

We Accept
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x 
1 x Me-163
1 x Waterproof adhesive tape, width 19mm, length 25m
1 x ABS angle 5,0x5,0x1000 mm
1 x Circlik for shaft 1.9 mm (10 pcs)
1 x Cross Connector 4.0 mm x 1000 mm
2 x CC 02
1 x SUS wire 3m (nylon coated)
1 x Walnut wood slat 2.0x2.0x1000 mm
1 x Hot Glue Stick RED
1 x BALSA triangular 8x8x1000 mm
1 x Jeti Black cap
1 x Monokote BLUE metalizado (1.8x0.65m)
2 x Short ball link M3 (6 uds)
1 x Oracover ROYAL RED 2m
1 x Canopy Latch
2 x Socket head long ball link M3 (2 uds)
1 x Steering arm 12 mm Ø 3 mm (2 uds)
1 x Pine wood slat 3.0x7.0x1000 mm
2 x Joint with bearing M2,5 22x5,5
1 x 76 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs)
2 x TP/TopFuel - JST-EH 4/5S Adapter
1 x Starter 12v (Max 90 and 15ccm)
1 x Glases Aspen
1 x Ball link M2,5 (10 pcs)
1 x Oracover Yellow CADMIO 10 m
1 x Walnut wood slat 3.0x3.0x1000 mm
1 x Zurich Sport Sunglasse Dark Sensity BROWN Glasses
2 x Futaba External voltage input cable Futaba CA-RVIN-700
2 x Ball link M3 (6 uds)
1 x Starter 12v (Max 180 and 30ccm)
1 x Cable silicona macho batt. receptor 30 cm (Futaba)
1 x Smoke set "Glider"
1 x Xplorer1 anemometro
1 x ABS tube 7.0x6.0x1000 mm
1 x ABS tube 6.0x5.0x1000 mm
1 x White smoke canister 140 g
1 x ABS tube 3.0x2.0x1000 mm
1 x Red smoke bombs AX-60 (5 pcs)
1 x Extension PVC 150 cm (Graupner)
1 x White silicone 0,25 qmm wire (150 m)
1 x Yellow smoke canister 100 g
1 x Cabel "Y" 15 cm
1 x Silicone 0,14 qmm servos wire Graupner (5 m)
1 x Xplorer2 anemometro
1 x Straightened rod Ø 1.5 mm x 1000 mm
1 x Straightened rod Ø 4.0 mm x 1000 mm
1 x Brass hexagonal rod Ø 4 mm x 1000 mm
1 x Aluminium rod Ø 4.0 mm x 3000 mm
1 x Propeller balancer
1 x Straightened rod Ø 2.0 mm x 1000 mm
1 x Straightened rod Ø 4.5 mm x 1000 mm
1 x Brass hexagonal rod Ø 3.5 mm x 1000 mm
1 x Propeller balancer
1 x L-Connector 1.0 mm x 1000 mm
1 x Profile ABS triangular 2.0x1000 mm 90º
1 x ABS "T" angle 10.0x10.0x1000 mm
1 x Profile ABS Square 4 x 1000 mm
1 x Autogyro Cierva C30 Spain
1 x Nut M2
1 x Bearing 3x6x2,5
1 x Bearing housing
1 x Side rudder
1 x Servo Fork
1 x Tail boom
1 x LA500 tail empennage
1 x Covered closure or fairings
1 x Schul-Malpinsel Gr.5
1 x Balance "Y" Wire 7S, 2x JST-XH / 1x JST-EH
1 x Male Prolonger TP 4/5S
1 x Set brocas Ø 1.2-1.4-1.6-1.8 mm (4 pcs)
1 x Dean "T" - Futaba Adapter
1 x PSC 5
1 x Male/Female prolonguer for Balancer Thunder Power 6S
1 x Set brocas Ø 1.5-2.0-2.5-3.0 mm (4 pcs)
1 x Multi-adapter balancer JST/C - TP
1 x Fully Threaded Steel Rod Duralumin 90 mm M3 (2 pcs)
1 x Pushrod greyline 3/2 with coupler M3 L: 1000 mm
1 x Birch plywood plate 600x300x3.0 mm
1 x Pushrod octagone 4/3
1 x M2,5 5Diam black ball link V2 (2 pcs)
1 x Birch plywood plate 600x300x2.0 mm
1 x 6 mm hexagonal ball link M3 (10 pcs)
1 x Birch plywood plate 600x300x2.5 mm
1 x Balsa panel 10x100x1000 mm
2 x Fully Threaded Steel Rod alumin 60 mm M3 (2 pcs) knurled
1 x 41x5,5 mm wires output (2 pcs)
1 x Balsa panel 6.0x100x1000 mm
1 x Joint with bearing M3 22x5,5
1 x Wheel collar 2 mm Ø (4 uds)
1 x M2 5Diam short black ball link V2 (2 pcs)
1 x M2/M1/6 3Diam short black ball link V1 (6 pcs)
1 x Aluminun wheel collar 2 mm Ø (4 uds)
1 x Aluminun wheel collar 3 mm Ø (4 uds)
1 x Hitec 38 mm servo arm with ball link
1 x DPSI Micro - DualBat 5.9V / 7.2V JR-JR (Dual Power Supply)
1 x Thixotropic agent TM 100, tin/ 75 g (approx. 1 l)
1 x Carbon tube (L 1000 mm, Ø4 mm, Ø3 mm)
1 x Hitec 25 mm servo arm with ball link
1 x CF tube (L 1000 mm Ø0,7 mm, Ø0,3 mm)
1 x DPSI LR-S (with push buttons)
1 x Carbon tube (L 1000 mm, Ø3 mm, Ø2 mm)
1 x OPTOTRONIX Aurora LCU
1 x ABS tube 9.0x8.0x1000 mm
1 x Glass Bubbles (0.12g) 400 G (aproxx 3.3 l)
1 x Carbon tube (L 1000 mm, Ø4 mm, Ø2,5 mm)
1 x Fuel bottle 500 ccm
2 x Fully Threaded Steel Rod Duralumin 70 mm M3 (2 pcs)
1 x Fully Threaded Steel Rod alumin 90 mm M3 (2 pcs)
1 x Crimping sleeves for cable 0.70 mm (10 pcs)
1 x Cockpit metalic closing
1 x TrainerCord (master-learner)
1 x JETImodel DPS 40
1 x MAX BEC 2D plus EX
1 x Long Switch On/Off micro
1 x PROXXON - SANDING BELTS FOR BSL 220/E 120 GRIT (5 pcs)
1 x "Y" charging 4mm wire (2 IN-1 OUT).
1 x CC 05
1 x Set brocas Ø 2.0-2.2-2.4-2.6 mm (4 pcs)
1 x Interruptor SPS 70v 60/120A
1 x Cabel charger transmitter GRAUPNER
1 x Switc electronic 30 Amp
1 x Fresa corte diamante Ø 1.4mm (bola)
1 x Circlick securite
1 x Precision wrench L100 mm
1 x Extension 2/3 lipos JST - JST/C
1 x Dust collector for mould cleaning
1 x Universal Filter
1 x Sealing Iron Sleeve STD
1 x SPS 70V 100/200 A
1 x Handle for PERMAGRIT lime
1 x 25 mm Sandpaper file
1 x Battery charging cable XT60
1 x Steel brush wheel with 2.35mm
1 x CC 01
1 x Red copper lacquer wire Ø0,2 mm (5 m)
1 x Black copper lacquer wire Ø0,2 mm (5 m)
1 x Concave-Convex sandpaper file 13 mm
1 x SPS 70V 140/280 A
1 x Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm)
1 x 22 mm Cut Disc Proxxon/Dremmel
1 x PROXXON - SILICON CARBIDE BELTS FOR BSL 220/E
1 x Fresa corte diamante Ø 2.35mm (flame)
1 x 30 cm BEC cable (female)
1 x Selfstart electronic switch
1 x Opto Gas Engine Kill Switch
1 x SBEC 30 D
1 x SBEC Jeti
1 x Pins M connect Multipin connectors AWG 20-24
1 x Balanceradapter JST-XH (Heli 47G) 2-6 c.
1 x Cabel charger battery transmiter Futaba 2x0,5 qmm (50 cm)
1 x MPX-Dean "T" Adapter
1 x Female prolonguer XH 30 cm 6 cell cable of silicone 0,25 mm
1 x Mini-handed clamp
1 x Sealing Iron Sleeve PROF
1 x 30 cm BEC cable (male)
1 x 2,0x50 mm allen screwdriver
1 x DPSI magnetic switch actuator (housing)
1 x Copper lacquer wire Ø0,2 mm (5 m)
1 x Hot Glue Stick BLACK
1 x 2 LiPo XH>EH adapter
1 x SBEC 40
1 x 5 LiPo XH>EH adapter
1 x 4 LiPo XH>EH adapter
1 x 3 LiPo XH>EH adapter
1 x Bec MR UBEC 5A (5v/6v/7v)
1 x Fresa corte diamante Ø 2.3mm (bola)
1 x MAX BEC
1 x Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH
1 x USB HLS prog. interface
1 x 
1 x PROXXON - SANDING BELTS FOR BSL 220/E 80 GRIT (5 pcs)
1 x Electronic switch JETI SP06 Opto
1 x 3 copper lacquer wire Ø0,2 mm (1 m)
1 x Male prolonguer XH 30 cm 6 cell cable of silicone 0,25 mm
1 x Set fresas corte Vanadium Ø 2.3/2.35 mm (3 pcs)
1 x SWTU2 switch
1 x Multi-adapter balancer JST - TP
1 x TP/TopFuel - XH 2/3S Adapter
1 x Adapter lead MPX/XT60
1 x APM2.6 Power module with 5.3V DC BEC
1 x Set brocas Ø 0.4-0.6-0.8-1.0 mm (4 pcs)
1 x DUPLEX USBa USB-Adapter for Jeti Duplex Items
1 x Adapter lead MPX/EC3
1 x CC 03
1 x Magnetic Interruptor MULTIPLEX
1 x Fully Threaded Steel Rod alumin 60 mm M3 (2 pcs)
1 x Balsa panel 2.0x100x1000 mm
1 x 28x5 mm wires output (2 pcs)
1 x 11 mm Rubber pads (14 pcs)
1 x Birch plywood plate 600x300x1.5 mm
1 x M2,5 Diam metal short ball link V3 (2 pcs)
1 x M2,5 5Diam short black ball link V2 (2 pcs)
1 x Blue metalic ball link M3/3 azul (2 pcs)
1 x Fully Threaded Steel Rod Duralumin 130 mm M3 (2 pcs)
1 x Fully Threaded Steel Rod alumin 40 mm M2,5 (2 pcs)
1 x Pushrod octagone 3/2 with coupler M2
1 x Fully Threaded Steel Rod alumin 80 mm M3 (2 pcs)
1 x Balsa panel 8.0x100x1000 mm
1 x Long ball link M1.6 (6 uds)
1 x Fully Threaded Steel Rod alumin 100 mm M3 (2 pcs)
1 x A/C quality beech plywood 600x300x5.0 mm
1 x M2,5 5Diam metal ball link V3 (2 pcs)
1 x quality beech plywood BIRCH 600x300x2.0 mm
1 x Balsa panel 1.5x100x1000 mm
1 x Fully Threaded Steel Rod Duralumin 110 mm M3 (2 pcs)
1 x Soporte grifo FESTO vertical (1 pcs)
1 x Socket head ball link M3 (2 uds)
1 x Blue metalic ball link M2/2 azul (2 pcs)
1 x Pushrod greyline 3/2 with coupler M2 L: 1000 mm
1 x Fully Threaded Steel Rod alumin 70 mm M3 (2 pcs)
1 x Pushrod octagone 3/2
1 x M2,5 Diam metal ball link V3 (2 pcs)
1 x Long ball link M2 (6 uds)
1 x Fully Threaded Steel Rod M2,5 (2 uds)
1 x Socket head long ball link M3 (6 uds)
1 x Ball link M2 (10 pcs)
1 x Landing gear frontal support 25x32x16
1 x Fully Threaded Steel Rod Duralumin 120 mm M3 (2 pcs)
1 x Birch plywood plate 600x300x1.2 mm
1 x Tip wing protector 30x10 (2 pcs)
1 x A/C quality beech plywood 600x300x0.6 mm
1 x Socket head ball link M3 (2 uds)
1 x Fully Threaded Steel Rod Duralumin 40 mm M3 (2 pcs)
1 x Long ball link M3 (6 uds)
1 x Fully Threaded Steel Rod alumin 50 mm M3 (2 pcs)
1 x Allen wheel collar M3x3
1 x Fully Threaded Steel Rod SUS303 65 mm M3 (2 pcs)
1 x A/C quality beech plywood 600x300x0.8 mm
1 x Balsa panel 1.0x100x1000 mm
1 x A/C quality beech plywood BIRCH 600x300x1.0 mm
1 x Cable tie mounts 4.3 (4 uds)
1 x A/C quality beech plywood 1520x750x3.0 mm
1 x Short ball link M2 (6 uds)
1 x Lite Plywood panel 600x300x2.0 mm
1 x Ball link M3 (10 pcs, flat ball)
1 x STEERING FRONT WHEEL SYSTEM BIDULE 111
1 x Fully Threaded Steel Rod Duralumin 34 mm M3 (2 pcs)
1 x Fully Threaded Steel Rod alumin 70 mm M2,5 (2 pcs)
1 x 6 mm ball link M3 (10 pcs)
1 x M3 Maxi ball link (2 uds)
1 x A/C quality beech plywood 600x300x6.0 mm
1 x Fully Threaded Steel Rod SUS303 70mm M3 (2 pcs)
1 x Tip wing protector 40x14 (2 pcs)
1 x A/C quality beech plywood 600x300x6.0 mm
1 x 38x4,5 mm wires output (2 pcs)
1 x M2/M1/6 3Diam long black ball link V1 (2 pcs)
1 x M3 Maxi ball link (2 uds)
1 x Joint with bearing M2 22x5,5
1 x Fully Threaded Steel Rod alumin 70 mm M3 (2 pcs) knurled
1 x A/C quality beech plywood 600x300x1.5 mm
1 x Wheel collar 6 mm Ø (4 uds)
1 x Birch plywood plate 600x300x3.0 mm
1 x Pushrod greyline 4/3 with coupler M3
1 x Fully Threaded Steel Rod alumin 80 mm M3 (2 pcs)
1 x A/C quality beech plywood 600x300x8.0 mm
1 x ABS tube 10.0x8.0x1000 mm
1 x ABS tube 2.0x1.0x1000 mm
1 x Hitec 20 mm servo arm
1 x Carbon tube (L 1000 mm, Ø18 mm, Ø16 mm)
2 x CF tube (L 1000 mm, Ø1 mm, Ø0,5 mm)
1 x Aluminium tube (L 1000 mm, Ø5.0 mm, Ø4.1 mm)
1 x 
1 x Carbon tube 3K-PW (L 1000 mm, Ø25 mm, Ø21 mm)
1 x DPSI OCP Overload protection
1 x DPSI Micro MPS
1 x Carbon tube (L 1000 mm, Ø12 mm, Ø10 mm)
1 x Futaba 25 mm servo arm with ball link
1 x Futaba 52 mm servo arm
1 x DPSI Ampere & Voltage bundle
1 x Hitec 30 mm servo rounded arm
1 x FUTABA 20 mm servo arm with ball link
1 x Aluminium tube (L 1000 mm, Ø7.0 mm, Ø6.1 mm)
1 x Glass Bubbles 0.19 g/cm³ Panda, tin/ 120 g (approx. 1 l)
1 x ABS tube 5.0x3.0x1000 mm
1 x Cotton Flocks, bag/ 500 g
4,774.74EUR
Manufacturers
Manufacturer Info
Night Fly
Night Fly Homepage
Other products
Languages
Español English
Currencies