16.00EUR

Opto Gas Engine Kill Switch
[SETOKW]

This kill switch is double Optically Coupled to isolate your ignition system from your radio system (No Interference!!). It also consist an additional safety functions.

Device features
• Includes a remote mountable ultra bright LED to indicate when the ignition is armed or not, or if the safety sequence protection is active.
• The LED diode informs also if Fail-Safe occured during flight (even after landing).
• Safety sequence protection for engine ignition powering up after model preparation.
• Double optically Coupled input/output is Isolated.
• Turning engine ignition ON or OFF directly from RC Transmitter
• No need to use additional mechanical switch for disconnecting ignition battery.
• 8 Bit microcontroller powered directly from RC receiver.
• 3,0 - 24,0 Volt Li-Po/Li-Ion/A123/Ni-Mh/NiCad Input (receiver side).
• 3,0 - 20,0 Volt Li-Po/Li-Ion/A123/Ni-Mh/NiCad MOSFET Output (ignition side).
• Possible to use one battery setup (independent two batteries setup by default).
• Max. current output: 5 Amp continous, 16 Amp peak
• Fail-Safe engine kill when interference or signal lose is longer then 1 second. (this function can be turned OFF).
• PPM-PCM 2048 – 1024 & 2.4Ghz Interface Support.
• Low Voltage Drop – Less than 150mv.
• 100% Surface Mount Technology.
• Heavy Gauge Wires 22AWG, universal connectors Futaba/JR.
• Small and light weight – only 15 Grams!

This device plugs into a spare receiver channel.

This is a must have safety device for any gas powered plane! This device allows you to safely kill your engine at anytime (on the ground, or inthe air!)

temporarily out of stock

Reviews

Customers who bought this product also purchased

Spark motor OS nº 3

temporarily out of stock

Quick Find

Shopping Cart

1 x	Cap Hispano Aviación
1 x	Softshell Hispano Aviación
1 x	Vest clothes Hispano Aviación
1 x	CellPRO 4S Adaptader (GP/KO up to 4S)
2 x	Cargador para AA/AAA Ni-MH & Ni-Cd
1 x	A/C quality beech plywood 498x247x1.2 mm
1 x	BALSA trip 3.0x3.0x1000 mm
1 x	Brass control horn M2 short for wire (2 pcs)
1 x	Gates hinge black 30x16 mm (2 pcs)
1 x	Gates hinge aluminium (1 pcs)
1 x	Horn 20x28,5 mm (2 pcs)
1 x	SIMtransmitter 6 Mode 2
1 x	Wing-connector: Glass / Carbon tube (26.5/25 x 25/23) x 1000 mm
1 x	Cable silicona macho batt. receptor 30 cm (Graupner)
1 x	ABS tube 4.0x3.0x1000 mm
1 x	Pin type hinge Al 4,5x70 mm (2 pcs)
1 x	Aluminun wheel collar 3.5 mm Ø (4 uds)
1 x	Nylon hinge for flaps/gates 27x10,5 (2 pcs)
1 x	Extension silicon 35 cm (Futaba)
1 x	Suncover 100cc Red
1 x	Cabel "Y" 30 cm (graupner)
1 x	Pin hinge 26x11 mm (10 uds)
1 x	Extension silicon 25 cm (Futaba)
1 x	ABS tube 7.0x6.0x1000 mm
1 x	Spikes Band (5 m)
1 x	Aluminun wheel collar 4 mm Ø (4 uds)
1 x	48 x 10 mm cylidric hinge Ø 3,0 mm (10 pcs)
1 x	M2/M1/6 3Diam short black ball link V1 (2 pcs)
1 x	ABS tube 16.0x14.0x1000 mm
1 x
1 x	BALSA trip 4.0x4.0x1000 mm
1 x	BALSA trip 2.0x2.0x1000 mm
1 x	Extension silicon 100 cm (Graupner)
1 x	Canopy Lock V1 M3 Red (2 pcs)
1 x	Joint with bearing M2 22x5,5
1 x	Allen wheel collar M3x5
1 x	A/C quality beech plywood 600x300x5.0 mm
1 x	Tape GFK 50 mm
1 x	33 x 8 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x	ABS tube 5.0x4.0x156 mm
1 x	Extension silicon 100 cm (Futaba)
1 x	ABS tube 3.0x2.0x330 mm
1 x	Carbon tube (L 1000 mm, Ø10 mm, Ø8 mm)
1 x	Carbon tube (L 1000 mm, Ø14 mm, Ø12 mm)
1 x	BALSA trip 6.0x6.0x1000 mm
1 x	Ball link M1.6 (6 uds)
1 x	Carbon fibre tube -TAPERED- 3k-PW (10 x 5 x 0.3) x 880 mm
1 x	BALSA triangular 8x8x1000 mm
1 x	Beech dowels 10 mm x 1000 mm
1 x	48 mm cylidric hinge Ø 2,5 mm (5 pcs)
1 x	Canopy Latch
1 x	20x1000 mm Ring Strap Back To Back
1 x	Gates hinge
1 x	ABS tube 9.0x7.0x1000 mm
1 x	Canopy Lock V1 M3 Blue (2 pcs)
1 x	Cable silicona macho batt. receptor 30 cm (Futaba)
1 x	A/C quality beech plywood BIRCH 600x300x1.0 mm
1 x	Balsa panel 1.5x100x1000 mm
1 x	Extension 7.5 cm
1 x	Horn micro type4 Ø 0,5 (2 pcs)
1 x	Horn mando small (2 pcs)
1 x	Cierre cabina aluminio Ø4, I=10 mm
1 x	Pad Screw Mount M3, up to 3mm / 0.12″, (10 pcs)
1 x	Aluminum Bayonet / strongal D12 mm / 0.5 m
1 x	Pin hinge 34x16 mm (10 uds)
1 x	Miniature brass strap hinge, 1 m
1 x	ABS tube 18.0x16.0x1000 mm
1 x	Extension silicon 50 cm (Graupner)
1 x	Cierre cabina aluminio Ø5, I=16 mm
1 x	Ball link M2 (10 pcs)
1 x	Tape GFK 38 mm
1 x	M2/M1/6 3Diam long black ball link V1 (2 pcs)
1 x	Hard aluminium thin-walled tube with fibreglass case ø30x1mm, 1m
1 x	6 mm aluminium horn with patella
1 x	Ball link M2,5 (10 pcs)
1 x	Fast'n EZ-CA-Hinge, lite (12 uds)
1 x	Horn 5/10 with M2 Bearing
1 x	Premium servo extension 100cm
1 x	Glases Nimbus "Black"
1 x	Green smoke canister 65 g
1 x	"S" set for planes
1 x	B4-0 rocket charges (6 pcs)
1 x	Glases Aspen
1 x	Red smoke canister 100 g
1 x	Central support Speed 280
1 x
1 x	Motor mount for 1200 mm models
1 x	Motor Mount for Multiplex FunJet
1 x	EasyFLY Addon
1 x	Micro Crystal RX 35.120 Ch 72
1 x	Hacker A30-S Radial Set
1 x	Crystal Universal RX 35.120 Ch 72
1 x	Receiver bed (Blue)
1 x	Ø 28 mm fiberglass motor-holder for electric motors
1 x	Indoor motor holder

1,042.96EUR