16.00EUR

Opto Gas Engine Kill Switch
[SETOKW]

This kill switch is double Optically Coupled to isolate your ignition system from your radio system (No Interference!!). It also consist an additional safety functions.

Device features
• Includes a remote mountable ultra bright LED to indicate when the ignition is armed or not, or if the safety sequence protection is active.
• The LED diode informs also if Fail-Safe occured during flight (even after landing).
• Safety sequence protection for engine ignition powering up after model preparation.
• Double optically Coupled input/output is Isolated.
• Turning engine ignition ON or OFF directly from RC Transmitter
• No need to use additional mechanical switch for disconnecting ignition battery.
• 8 Bit microcontroller powered directly from RC receiver.
• 3,0 - 24,0 Volt Li-Po/Li-Ion/A123/Ni-Mh/NiCad Input (receiver side).
• 3,0 - 20,0 Volt Li-Po/Li-Ion/A123/Ni-Mh/NiCad MOSFET Output (ignition side).
• Possible to use one battery setup (independent two batteries setup by default).
• Max. current output: 5 Amp continous, 16 Amp peak
• Fail-Safe engine kill when interference or signal lose is longer then 1 second. (this function can be turned OFF).
• PPM-PCM 2048 – 1024 & 2.4Ghz Interface Support.
• Low Voltage Drop – Less than 150mv.
• 100% Surface Mount Technology.
• Heavy Gauge Wires 22AWG, universal connectors Futaba/JR.
• Small and light weight – only 15 Grams!

This device plugs into a spare receiver channel.

This is a must have safety device for any gas powered plane! This device allows you to safely kill your engine at anytime (on the ground, or inthe air!)

temporarily out of stock

Reviews

Customers who bought this product also purchased

Spark motor OS nº 3

temporarily out of stock

Quick Find

Shopping Cart

1 x	Nose OPTIMA 2.200 mm (Elec or Glider)
1 x	Motor mount VANQUIST 48" F3A
1 x	Metalic nose for PROJETI
1 x	Motor mount class 48"
1 x	Motor mount EDGE 540 48"
1 x	105 mm PVC transparent battery termo-retract 68 mm (1 m)
1 x	Cable silicona macho batt. receptor 30 cm (Graupner)
1 x	20 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	Kwik link AL M4 L:40 mm (2 pcs) + Pin Ø 2,5 mm
1 x	Aluminium tube (L 1000 mm, Ø7.0 mm, Ø6.1 mm)
1 x	200 mm extensión servo HITEC/JR
1 x	Aluminium tube (L 1000 mm, Ø3.0 mm, Ø2.1 mm)
1 x	Crystal Universal RX 35.030 Ch 63
1 x	Crystal TX 35.010 Ch 61
1 x	Straightened rod Ø 6.0 mm x 1000 mm
1 x	ABS tube 7.0x5.0x1000 mm
1 x	Crystal Universal RX 35.090 Ch 69
1 x	Hard aluminium thin-walled tube with fibreglass case ø30x1mm, 1m
1 x	Plasti Dip Liquid Tape 429 ml orange
1 x	PPM Encoder Module
1 x	Spannlack 1000 ml
1 x	Hobbylite Filler, Balsa colour
1 x	Paint gun for sprays
1 x	Wing-connector: Glass / Carbon tube (13.7/12.5) x 1000 mm
1 x	White smoke bombs AX-3 (10 pcs)
1 x	ABS "T" angle 10.0x10.0x1000 mm
1 x	Rubber profile 8-2 mm 2M
1 x	ABS angle 1.5x1.5x1000 mm
1 x	110x55 mm SLH KOVO wheel
1 x	White smoke canister 65 g
1 x	Profile ABS triangular 6.0x1000 mm 90º
1 x	10 mm floating pad (72 pcs)
1 x	Streamline Stainless Steel Tubing 10.5x5.7x1000 m
1 x	Profile ABS triangular 2.0x1000 mm 90º
1 x	Cross Connector 4.0 mm x 1000 mm
1 x	Parachute expulsion foam
1 x	Brass control horn M4 long for wire (4 pcs)
1 x	Duralumium F3A horn 30x10x23,5 mm (2 pcs)
1 x	Aluminium cap bolt washer M4 green (8 pcs)
1 x	20 mm carbon horn
1 x	Rubber profile 10-2 mm 2M
1 x	1/10 Pilot "Jimmy"
1 x	Ventral support for AX-18/AX-60
1 x
1 x	Opto Gas Engine Kill Switch
1 x	1/6 Pilot "Garry"
1 x	Joint with bearing M2 22x5,5
1 x	Ball link M2 (10 pcs)
1 x	M2/M1/6 3Diam short black ball link V1 (2 pcs)
1 x	Joint with bearing M2,5 22x5,5
1 x	M2 5Diam short black ball link V2 (2 pcs)
1 x	1/6 Pilot "Buddy"
1 x	1/4 Pilot "Heidi"
1 x	Joint with bearing M3 22x5,5
1 x	M2 5Diam black ball link V2 (2 pcs)
1 x	M2/M1/6 3Diam short black ball link V1 (6 pcs)

509.30EUR