84.90EUR

Battery LiFe TopFuel 3100 mAh 3s MTAG 30C
[HK93100351]

Product description and features
The TopFuel LiFe-EC cells are built in a flat, LiPo-like design and therefore fit perfectly into almost any existing battery compartment.
The main difference to LiPo and LiIon batteries is the lower voltage of 3.3 volts to a maximum of 3.6 volts per cell. LiFe batteries are significantly less sensitive to under- and over voltage. They are characterized by a very constant and flat discharge curve and a very high cycle stability.
The battery is readymade soldered with the XT60 connector system.
Connections
XT60 connector with gold contacts, suitable up to 60 amps permanent current.
XH balancer connector
Internal chip for battery telemetry
Battery data such as type, number of cells, capacity, C-rate or battery ID are stored on the passive MTAG chip. If desired* these values can be read out with an external NFC sensor such as the HACKER or JETI MTAG and be transferred to the transmitter telemetry system.
The built-in MTAG chip also offers the possibility of manually or automatically counting and storing the charging cycles. By using several identical batteries in serial or parallel operation, so more effective active battery management is possible.
*Note: It is up to the user if he wants to use the MTAG function or not. The TopFuel battery can be used without MTAG function like any ordinary battery.

Specifications
Battery type LiFe
Ausführung 3S
Cells 3
Nominal voltage [V] 9,9
Capacity [mAh] 3100
C rate 30C
Balancer connector XH
Dimensions and Weight
Length [mm] 136
Width [mm] 42
Height [mm] 23
Weight [g] 260

under request

Reviews

Quick Find

Shopping Cart

1 x	Balance "Y" Wire 7S, 2x JST-XH / 1x JST-EH
1 x	Cabel charger transmitter GRAUPNER
2 x	Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm)
1 x	Balance "Y" Wire 6S, 2x JST-XH / 1x JST-EH
2 x	3 LiPo XH>EH adapter
1 x	Bec MR UBEC 5A (5v/6v/7v)
1 x	Red copper lacquer wire Ø0,2 mm (5 m)
1 x	CC 05
1 x	CM-3
1 x	CC 01
1 x	2 LiPo XH>EH adapter
1 x	APM2.6 Power module with 5.3V DC BEC
1 x	30 cm BEC cable (male)
1 x	Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm)
1 x	CC 03
2 x	JETImodel SINGLE BEC
1 x	Balanceradapter JST-XH (Heli 47G) 2-6 c.
2 x	Cabel charger battery transmiter Futaba 2x0,5 qmm (50 cm)
2 x	Dean "T" - Futaba Adapter
1 x	"Y" charging 4mm wire (2 IN-1 OUT).
1 x	13 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	Cinta Goldfix 1m
1 x	SE Ring 300 mm (2 pcs)
1 x	ABS Strip 1.5x6.0x1000 mm
1 x	20x1000 mm Ring Strap Back To Back
1 x	Strip ABS 2.0x10.0x1000 mm
1 x	ABS Strip 1.0x4.0x1000 mm
1 x	Round Rod 3,0x1000 mm
1 x	Round Rod 1,0x1000 mm
2 x	ABS Strip 1.5x2.0x1000 mm
1 x	Round Rod 2,0x1000 mm
1 x	14x60 mm Mini rings Tie Wraps (4 pcs)
1 x	ABS Strip 1.5x8.0x1000 mm
1 x	Round Rod 1,5x1000 mm
1 x	5 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x	Strip 2,5x1,25x330 mm
1 x	Round Rod 1,25x1000 mm
1 x	Strip ABS 2.0x5.0x1000 mm
1 x	Round Rod 2,5x1000 mm
2 x	SE Ring 360 mm (2 pcs)
1 x	SE Ring 400 mm (2 pcs)
2 x	Round Rod 6,0x1000 mm
1 x	SE Ring 350 mm (2 pcs)
1 x	SE Ring 480 mm (2 pcs)
1 x	Strip 1,5x1,5x330 mm
1 x	Strip 3,5x1,75x330 mm
1 x	13 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
2 x	Round Rod 4,0x1000 mm
1 x	SE Ring 200 mm (2 pcs)
1 x	Pad self adhesive, up to 3mm / 0.12″, (10 pcs)
1 x	RUDDOG Protection and Heat Shield Tape (2mx50mm)
3 x	ABS Strip 1.5x3.0x1000 mm
1 x
1 x	SE Ring 330 mm (4 pcs)
1 x	SE Ring 240 mm (2 pcs)
1 x	ABS Strip 1.0x5.0x1000 mm
1 x	Marker ties (20 pcs)
1 x	Spikes Band (5 m)
1 x	SE Ring HACKER 300 mm (2 pcs)
2 x	Round Rod 5,0x1000 mm
1 x	Strip 2,0x2,0x330 mm
1 x	ABS Strip 1.5x4.0x1000 mm
1 x	Horn 6/27 with M3 Bearing
1 x	Parachute expulsion foam
1 x	Parachutist
1 x	Oracover CARBON Metalic 1 m
1 x	SPS 70V 140/280 A
1 x	3 copper lacquer wire Ø0,2 mm (1 m)
1 x	5 LiPo XH>EH adapter
1 x	DPSI Ampere battery backer
1 x	Female prolonguer XH 30 cm 6 cell cable of silicone 0,25 mm
1 x	Copper lacquer wire Ø0,2 mm (5 m)
2 x	Adapter lead MPX/EC3
1 x	Extension 5 lipos JST/C - JST
1 x	Female connector JST SH 1.0mm with 10 cm wire
1 x	Double conector with JR adapter and 200 mm extension
1 x	Prolonguer for Balancer Thunder Power 6S
1 x	PWC4 wing/fuselage connector for 4 servos
1 x	TP/TopFuel - XH 2/3S Adapter
1 x	Servo slow down unit (0,7-14,7 sec )
1 x	SPS Remote switch actuator
1 x	SPARK Switch 7.4v
1 x	Landing gear Rocket 400
1 x	Helices DJI Mavic Air 2 STEALTH "Black" (4x Ud)
1 x	DUPLEX USBa USB-Adapter for Jeti Duplex Items
1 x	Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH
1 x	Tape GFK 38 mm
1 x	Sparkplug 1/4-32 EVO 10GX
1 x	GPS Expander Module
1 x	Y Cable
1 x	Spark motor OS Type F
1 x	Sparkplug NGK CM6
1 x	Gates hinge
1 x	Canopy hinges for Discus 2c, Discus 2a, Ventus 2cx (2pcs)
1 x	Pin type hinge Al 3,0x50 mm demount (2 pcs)
1 x	15 mm reinforced hinge
1 x	Nylon hinge for flaps/gates 27x10,5 (2 pcs)
1 x	Pin type hinge Al 4,5x70 mm (2 pcs)
1 x	Gates hinge 30x16 mm (2 pcs)
1 x	Large flex hinge (12 uds)
1 x	Nylon hinge 20x15x0,3 (10 pcs)
1 x	Pin hinge 34x16 mm (10 uds)
1 x	WingFix ULTRA Black Edition
1 x	Field folding model stand SebArt
1 x	120x60 mm SLH KOVO wheel
1 x	SIMtransmitter 6 Mode 2
1 x	67 x 12 mm cylidric hinge Ø 4,5 mm (10 pcs)
1 x	Interface Jack Adapter IKARUS
1 x	RF9 Flight Simulator with Spektrum Controller
1 x	Propeller balancer
1 x	26 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	Cable-Tie 1.66x71mm / 0.07x2.8″ (20 pcs)
1 x	ABS Strip 1.0x3.0x1000 mm
1 x	ABS I Strip 20x10x1000 mm
1 x	ABS Strip 1.0x2.0x1000 mm
1 x	20x200 mm battery rings
1 x	JETImodel Addcap 1640
1 x	Female connector for 20 pines AWG
1 x	Male prolonguer XH 30 cm 6 cell cable of silicone 0,25 mm
1 x	Extension 2/3 lipos JST - JST/C
1 x	Male connector for 10 pines AWG
1 x	JETImodel DPS 40
1 x	Aluminium Hub for folding Props 37 mm M8 Shaft 5 mm
1 x	Bearings for motors hacker A50

1,989.53EUR