17.00EUR

Hardener Aero EPH 161 (500 g)
[R11212505]

Hardener Aero EPH 161 (500 g)

Hardener for Epoxy Resin L and L 20, EP Gel coat colourless and Mould Resin P
Contains no formaldehyde and no paraformaldehyde
Epoxy Resin L
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by hot curing for: approx. 10 h at 60 °C
Max. heat distortion temperature after annealing: 120 °C
Laminate structures for vehicle construction in combination with this product and epoxy resin L are approved by the TÜV-Süd. Process instructions/TÜV-Report (unfortunately only in German)
Epoxy Resin L 20
The combination of L 20 and Hardener EPH 161 yields a low-viscosity laminating resin that exhibits superior impregnating and wetting properties to glass, aramid, and carbon fibres. In conjunction with L 20, hardener EPH 161 results in a long service life for the resin compound with very high mechanical and dynamic strengths and perfect curing in both thick (> 2 cm) and thin (1,5 mm) laminates. Before they can obtain the specified mechanical properties, the laminates must be post-cured for about fifteen hours at 60 °C after their initial cold-curing period.
The system L 20 + EPH 161 is approved for the construction of gliders.
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by post-curing: for 15 h at 60 °C
Gel coat colourless
Processing time: 90 minutes
Mixing ratio:
100 : 24 parts by weight EP Gel coat : Hardener EPH 161
Curing time: 24 h at room temperature, afterwards hot curing approx. 10 h/60 °C (recommended, but not necessary).
Max. heat distorsion temperature after annealing: approx. 120 °C
Mould resin P
Processing time: 90 minutes
Mixing ratio:
100 : 17 parts by weight Mould Resin P : Hardener EPH 161
Gelling time: approx. 4 h
Curing time: 24 h at roomtemperature, afterwards hot curing: approx. 15 h/60 °C
Please order resin L and L 20, gel coatcolourless and mould resin P separately

under request

Reviews

Quick Find

Shopping Cart

1 x	Carbon fiber flat 1000x3.0x0.13 mm
2 x	Carbon fiber flat 1000x3.0x1.0 mm
1 x	Carbon fiber rod 2.5 mmx1000 mm
1 x	Carbon fiber flat 1000x6.0x0.8 mm
1 x	Carbon fiber rod 7.0 mmx1000 mm
2 x	Carbon fiber rod 1.5 mm x 1000 mm
3 x	Carbon fiber rod 5.0 mmx1000 mm
1 x	Carbon fiber rod 3.0 mm x 1000 mm
2 x	Carbon fiber rod 2.0 mmx1000 mm
1 x	DPS Switch JR/JR
2 x	2 LiPo XH>EH adapter
1 x	Balanceradapter JST-XH (Heli 47G) 2-6 c.
2 x	Adapter lead MPX/EC3
1 x	Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm)
1 x	DPSI Ampere battery backer
1 x	CC 02
1 x	Solvent Plasti Dip 1000 ml
1 x	ABS "T" angle 6.0x6.0x1000 mm
1 x	Nitroverdu 500 ml
1 x	Profile ABS triangular 4.0x1000 mm 90º
1 x	Threaded coupler M2 (10 uds)
1 x	SE Ring HACKER 300 mm (2 pcs)
1 x	M3-M4 rubber washer (8 pcs)
1 x	Conector JR Servo female (50 pcs)
1 x	Piloto RC Civil 1/5- 1/6 Scale 12"
1 x	Carbon rectangular rod 3.0 mm x 1.0 x 1000 mm
1 x	Carbon fiber rod 1.5 mm x 1000 mm
1 x	Carbon fiber rod 12 mm x 1000 mm
1 x	Carbon rectangular rod 10.0 mm x 1.0 x 1000 mm
1 x	Carbon fiber rod 14 mmx1000 mm
1 x	DYNAMOMETER S-1580
1 x	Balance "Y" Wire 5S, 2x JST-XH / 1x JST-EH
1 x	Circlick securite
1 x	Cabel charger transmitter GRAUPNER
1 x	4 LiPo XH>EH adapter
1 x	CC 01
1 x	APM2.6 Power module with 5.3V DC BEC
1 x	Copper lacquer wire Ø0,2 mm (5 m)
1 x	CM-3
1 x	Propeller APC 13x6.5 Electric
1 x	Propeller APC 11x4.7 SF Pusher
1 x	Propeller APC 10x5.5 MR Electric multirrotor PUSHER
1 x	Propeller APC 11x8.5 Electric
1 x	Propeller APC 11x8 Electric
1 x	Propeller APC 10x4.7
1 x	Propeller APC 13x10 Electric
1 x	Propeller APC 10x5.5 MR Electric multirrotor
1 x	Propeller APC 12x10 Electric
1 x	Propeller APC 11x4.5 Electric Pusher
1 x	Propeller APC 12x6 Electric
1 x	Propeller APC 13x4 Electric Pusher
1 x	20-25mm Servo Arm
1 x	Aluminum Bayonet / strongal D35 mm / 1 m
1 x	Blue metalic ball link M3/3 azul (2 pcs)
1 x	Long ball link M3 (6 uds)
1 x	Balance "Y" Wire 6S, 2x JST-XH / 1x JST-EH
1 x	BEC 3A FOXY
1 x	"Y" charging 4mm wire (2 IN-1 OUT).
1 x	CC 03
1 x	Dean "T" - Futaba Adapter
1 x	Adapter lead MPX/XT60
1 x	Black copper lacquer wire Ø0,2 mm (5 m)
1 x	Small aluminium horn gold (2pcs)
1 x	20 mm carbon horn
1 x	Servo GO-1023MG 7.0 kg.cm 0.09s/60º
1 x	Horn 16,5x20 mm (2 pcs)
1 x	Horn 20x28,5 mm (2 pcs)
1 x	6 mm red aluminium threaded horn with patella
1 x	Threaded coupler ALU Left M3 Ø 4 (2 uds)
1 x	LH long aluminium horn L31xH30 (2pcs)
1 x	Regulador Jeti Jes 045
1 x	Squared carbon wing joinner 5x5x220 mm
1 x	Cyanoacrylate MD GLUE plus 405, for extreme loads 20g
1 x	Digital scale up to 40 kg
1 x	TeXtreme® Carbon tape 38 g/m² (IM, unidirectional) 20 mm x 100m
1 x	Kavan Car 25% nitro 1l
1 x	Wing-connector: Glass / Carbon tube (13.7/12.5) x 1000 mm
1 x	Cyanocrylate MD GA460 odourless 20g

1,991.68EUR