17.00EUR

Hardener Aero EPH 161 (500 g)
[R11212505]

Hardener Aero EPH 161 (500 g)

Hardener for Epoxy Resin L and L 20, EP Gel coat colourless and Mould Resin P
Contains no formaldehyde and no paraformaldehyde
Epoxy Resin L
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by hot curing for: approx. 10 h at 60 °C
Max. heat distortion temperature after annealing: 120 °C
Laminate structures for vehicle construction in combination with this product and epoxy resin L are approved by the TÜV-Süd. Process instructions/TÜV-Report (unfortunately only in German)
Epoxy Resin L 20
The combination of L 20 and Hardener EPH 161 yields a low-viscosity laminating resin that exhibits superior impregnating and wetting properties to glass, aramid, and carbon fibres. In conjunction with L 20, hardener EPH 161 results in a long service life for the resin compound with very high mechanical and dynamic strengths and perfect curing in both thick (> 2 cm) and thin (1,5 mm) laminates. Before they can obtain the specified mechanical properties, the laminates must be post-cured for about fifteen hours at 60 °C after their initial cold-curing period.
The system L 20 + EPH 161 is approved for the construction of gliders.
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by post-curing: for 15 h at 60 °C
Gel coat colourless
Processing time: 90 minutes
Mixing ratio:
100 : 24 parts by weight EP Gel coat : Hardener EPH 161
Curing time: 24 h at room temperature, afterwards hot curing approx. 10 h/60 °C (recommended, but not necessary).
Max. heat distorsion temperature after annealing: approx. 120 °C
Mould resin P
Processing time: 90 minutes
Mixing ratio:
100 : 17 parts by weight Mould Resin P : Hardener EPH 161
Gelling time: approx. 4 h
Curing time: 24 h at roomtemperature, afterwards hot curing: approx. 15 h/60 °C
Please order resin L and L 20, gel coatcolourless and mould resin P separately

under request

Reviews

Quick Find

Shopping Cart

1 x	Stainless steel cable Ø 0.52 mm - 15 kp (10 m)
1 x	Steering arm 16 mm Ø 3 mm (2 uds)
1 x	Screw-lock connector Ø 2 mm (2 uds)
1 x	Stainless steel cable Ø 0.62 mm (10 m)
1 x	Locking cable tie 4.6x203 (uds)
1 x	Cockpit plastic closing
1 x	Steering arm 16 mm Ø 4 mm (2 uds)
1 x	Crimping sleeves for cable 0.85 mm (10 pcs)
1 x	Steering arm 12 mm Ø 4 mm
1 x	Steering arm 12 mm Ø 4 mm (2 uds)
1 x	Cabin latch Fox MDM1 4m (pair)
2 x	One touch canopy lock
1 x	Micro screw-lock pushrod conn snap Ø 1 mm (2 uds)
1 x	Stainless steel cable Ø 0.5 mm (2 m)
2 x	Stainless steel cable Ø 0.88 mm - 60 kp (10 m)
1 x	Screw-lock connector M2 (2 uds)
1 x	Vertical cockpit anchor "tipe F3A" (2 pcs)
1 x	Crimping sleeves for cable 0.70 mm (10 pcs)
1 x	Steering arm 16 mm Ø 4 mm
2 x	Jeti Black cap
1 x	EC5-Set male, simple quality, 2 x female pin, 1 x blue housing
1 x	Hot Glue Stick RED
1 x	Cable silicona macho batt. receptor 30 cm (Graupner)
1 x	20x200 mm battery rings
1 x	5 line servos wire black (1 m)
1 x	Civilian pilot "Gramps" size 9cm (Slimline)
1 x	Angle support XT60 conector
1 x	Support Antena 2.4 Ghz (2 pcs)
1 x	Tube support Ø 6mm (10 pcs)
1 x	Allen wheel collar M3x5
2 x	Cable tie mounts 4.3 (4 uds)
1 x	Cierre cabina aluminio Ø4, I=10 mm
1 x	45 mm rods set for direction control
1 x	Cable grommet Ø 6.4 mm (4 uds)
1 x	100 mm rods set for direction control
1 x	Locking cable tie 2.5x100 (uds)
1 x	Allen wheel collar M4x4
1 x	Fully Threaded Steel Rod M2,0 (2 uds) 250mm
1 x	Canopy Latch
1 x	Pushrod octagone 3/2
1 x	Snap for floding prop for 2 mm axi
1 x	Tip wing protector 28x10x12 (2 pcs)
1 x	Ventus 1:4 set of instruments
1 x	3x8W Triple-Spotlight, 12mm, T-Fuse White
1 x	Jet Afterburner Simulator NF-Jet3 RYS
1 x	Jet Afterburner Simulator NF-Jet1RY Set
1 x	LED blink wire flashing (orange - 2pcs)
1 x	LED wire (green - 2pcs)
1 x	Jet Afterburner Simulator NF-Jet2
1 x	Extractor piñones 2.3/3.2 mm
1 x	SERVO DES 806 Pignons
1 x	Heat sink for Optotronix LEDs
2 x	LED wire (white - 2pcs)
1 x	Cover cap drop-shaped paintable 43 mm
1 x	Resistor 3W 5% 2R2
1 x	Set luces Airliner 2.1m Wingspan Scale 1:14 Civil/Sport
1 x	LED lighting system High Power
1 x	Jet Afterburner Simulator NF-Jet3 YSW
1 x	Lense for Spotlights, 20mm
1 x	Resistor 3W 5% OR82
1 x	Xoar Electric Beechwood Prop 22x10
1 x	Xoar Electric Beechwood Prop 16x7
1 x	Xoar Electric Beechwood Prop 24x8
1 x	Xoar Electric Beechwood Prop 12x6
1 x	Xoar Electric Beechwood Prop 15x8
1 x	STEERING FRONT WHEEL SYSTEM BIDULE 55
1 x	Adapter 4,0 mm M8
1 x	Aluminun wheel collar 6 mm Ø (4 uds)
1 x	Motor OS 3805-1200 electric
1 x	Motor Mega AC 16/07/06
1 x	3 mm Long Prop Adapter M5
1 x	12 mm dogdrive props
1 x	Triple rod con. 2mm Pushrod (2 pcs)
1 x	Adapter 5,0 mm M6 for spinner 40 mm fixed propeller
1 x	3 mm Short Prop Adapter M5
1 x	Allen wheel collar M4x6
1 x	Aluminun wheel collar 2.5 mm Ø (4 uds)
1 x	Tip wing protector 40x14 (2 pcs)
1 x
1 x	Allen wheel collar M3x3
1 x	Wheel collar 3.5 mm Ø (4 uds)
1 x	5 mm Prop Adapter M6
1 x	Power MULTIlight
1 x	Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 100 m
1 x	Cyanocrylate MD GA460 odourless 20g
1 x	Release wax 250ml
1 x	Carbon roving DowAksa / 24k / 1600 tex
1 x	Straightened threaded rod M3 - 1m
1 x	Conector JR Servo female (50 pcs)
1 x	ESC PULSAR A-40
1 x	Jet Afterburner Simulator NF-Jet3 RY
1 x	NF-3X-80 liner Kit
1 x	ED Position Lights wireless (Set of 3)
1 x	Motor Mega AC 16/15/04
1 x	Wheel collar 6 mm Ø (4 uds)
1 x	Motor Mega AC 16/25/02
1 x	Horizontal cockpit anchor "tipe F3A" (2 pcs)
1 x	Aluminun wheel collar 3.5 mm Ø (4 uds)
1 x	Disposable Injector Bags (30x16cm) 100 pcs
1 x
1 x	Wing-connector: Glass / Carbon tube (26.5/25 x 25/23) x 1000 mm
1 x	CA Glue (medium) 20g
1 x	ARAMID honeycomb 1300x2600x2 mm
1 x	Carbon fibre tape 200 g/m² (unidirectional) 50 mm
1 x	Vacuum bag, 1200 mm x 50 m
1 x	Hardener Aero EPH 161 (250 g)
1 x	Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 50 m
1 x	Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 10 m
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x1.2 mm (10 pcs)
1 x	Hardener Aero EPH 161 (500 g)
1 x	FOX 2.300 mm V2 PNP (FMS)
1 x	Cyanoacrylate MD GLUE plus 405, for extreme loads 20g

3,573.62EUR