17.00EUR

Hardener Aero EPH 161 (500 g)
[R11212505]

Hardener Aero EPH 161 (500 g)

Hardener for Epoxy Resin L and L 20, EP Gel coat colourless and Mould Resin P
Contains no formaldehyde and no paraformaldehyde
Epoxy Resin L
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by hot curing for: approx. 10 h at 60 °C
Max. heat distortion temperature after annealing: 120 °C
Laminate structures for vehicle construction in combination with this product and epoxy resin L are approved by the TÜV-Süd. Process instructions/TÜV-Report (unfortunately only in German)
Epoxy Resin L 20
The combination of L 20 and Hardener EPH 161 yields a low-viscosity laminating resin that exhibits superior impregnating and wetting properties to glass, aramid, and carbon fibres. In conjunction with L 20, hardener EPH 161 results in a long service life for the resin compound with very high mechanical and dynamic strengths and perfect curing in both thick (> 2 cm) and thin (1,5 mm) laminates. Before they can obtain the specified mechanical properties, the laminates must be post-cured for about fifteen hours at 60 °C after their initial cold-curing period.
The system L 20 + EPH 161 is approved for the construction of gliders.
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by post-curing: for 15 h at 60 °C
Gel coat colourless
Processing time: 90 minutes
Mixing ratio:
100 : 24 parts by weight EP Gel coat : Hardener EPH 161
Curing time: 24 h at room temperature, afterwards hot curing approx. 10 h/60 °C (recommended, but not necessary).
Max. heat distorsion temperature after annealing: approx. 120 °C
Mould resin P
Processing time: 90 minutes
Mixing ratio:
100 : 17 parts by weight Mould Resin P : Hardener EPH 161
Gelling time: approx. 4 h
Curing time: 24 h at roomtemperature, afterwards hot curing: approx. 15 h/60 °C
Please order resin L and L 20, gel coatcolourless and mould resin P separately

under request

Reviews

Quick Find

Shopping Cart

1 x	30 cm DEANS female connector
1 x	PowerBox Evo
1 x	Gold antispark 5,5 mm plug
1 x	Conector BEC female (10 pcs)
1 x	Extension for SensorSwitch 30cm
1 x	PowerBox MagSensor black connector SRS/Champion
1 x	Connectors banna gold 5,5 mm (M/F)
1 x	PowerBox Champion SRS
1 x	Connectors banna oro 6,0 mm (M/F)
1 x	EC5-Set female, simple quality, 2 x female pin, 1 x blue housing
1 x	XH female balance (4S) connector (2 pcs)
1 x	Connectors banna oro 8,0 mm 5 pcs(Female)
1 x	MicroMatch PowerBox
1 x	Connectors banana oro 6,0 mm Ultralight (M/F)
1 x	XH male balance (2S) connector (2 pcs)
1 x	Hot Glue Stick RED
1 x	Starter Sullivan-STAR 603 DINATRON
1 x	Digital precision scale up to 2000 g
2 x	3,0x60 mm allen screwdriver
2 x	Starter EM Gear Power 250
1 x	Starter Sullivan-STAR 601
1 x	Screwdriver for Hexagon 1,27mm
1 x	Disposable Injector Bags (30x16cm) 100 pcs
1 x	Z Bender - S Type Tool
1 x	Ball Link Plier
1 x	PROXXON - SANDING BELTS FOR BSL 220/E 120 GRIT (5 pcs)
1 x	Screwdriver for Torx® TX8
1 x	Starter EM Gear Power 80
1 x
3 x	Vacuum pump 12 CFM
1 x	PROXXON - SANDING BELTS FOR BSL 220/E 80 GRIT (5 pcs)
2 x	Starter 12v (Max 90 and 15ccm)
1 x	Crimping tool
1 x	Vacuum pump P1-N
2 x	2,5x60 mm allen screwdriver
1 x	Z Bender - S Type Tool
2 x	PROXXON - SANDING BELTS FOR BSL 220/E 180 GRIT (5 pcs)
1 x	Starter 12v (Max 180 and 30ccm)
1 x	Cut tube
1 x	Hexagonal ball head 2.0 x 50 mm
2 x	Crimping tool
3 x	Tube Pitot to PIXHAWK
1 x	PPM Encoder Module
1 x	PIX Hawk with accesories
1 x	Cabel charger battery transmiter Graupner 2x0,5 qmm (50 cm)
1 x	CC 03
1 x	Bec MR UBEC 5A (5v/6v/7v)
1 x	4 LiPo XH>EH adapter
3 x	APM2.6 Power module with 5.3V DC BEC
1 x	Balanceradapter JST-XH (Heli 47G) 2-6 c.
1 x	TP/TopFuel - JST-EH 4/5S Adapter
1 x	"Y" charging 4mm wire (2 IN-1 OUT).
2 x	3 LiPo XH>EH adapter
2 x	Cabel charger battery transmiter Multiplex 2x0,5 qmm (50 cm)
2 x	2 LiPo XH>EH adapter
1 x	CM-3
1 x	5 LiPo XH>EH adapter
2 x	30 cm BEC cable (female)
1 x	Dean "T" - Futaba Adapter
1 x	Brass control horn M4 short for wire (10pcs)
1 x	Pilot "Anthony" (Slimline)
1 x	Threaded coupler ALU M3 Ø 6 (2 uds)
1 x	Green smoke canister 65 g
1 x	Straightened rod Ø 7.0 mm x 1000 mm
1 x	6 mm Quick clamp_S (10 pcs)
1 x	Carbon fibre tape 125 g/m², 3k, UD (25 mm) roll/ 50 m
1 x	Tapa estado carga XT-60 (6 pcs)
2 x	Support Flush MPX Conector (6 pcs)
1 x	Support FUEL DOT V3
1 x	Aro pasacable Ø20 mm (4 pcs)
1 x	Black copper lacquer wire Ø0,2 mm (5 m)
1 x	Tool for entel
1 x	Copier 5x20 cm pcs
1 x	Pistola termica MH 550 micro
1 x	Fabric scissors curved (offset handles), 16 cm / 6" length
1 x	Digital weight, angle and balance meter BASIC
1 x	Set brocas Ø 0.4-0.6-0.8-1.0 mm (4 pcs)
2 x	Roller cutter 28 mm
1 x	25 mm Sandpaper file
1 x	Propeller drill jig DA 100/85/120/150/200 and VM 60-210
1 x	Set brocas Ø 1.2-1.4-1.6-1.8 mm (4 pcs)
1 x	Vacuum Connection VA 1 (for hose Ø 6 mm)
1 x	Motor mount EDGE 540 48"
1 x	DPSI RV Mini 6 (2008)
1 x	Jet Afterburner Simulator NF-Jet2
1 x	Servo HBS 690BB HV Digital
1 x	Extension silicon 35 cm male (Futaba)
1 x	Cabel "Y" 30 cm (graupner)
1 x	Futaba Female 40 cm extension
1 x	Extension 90 cm (Futaba)
1 x	Antenna holder bracket double
1 x	White 2,4 GHz antenna exit guides (2 pcs)
1 x	XT-60 Plug Mold
1 x	Laminating brush 10 mm, pack/ 50 pcs
1 x	Set fresas corte Vanadium Ø 2.3/2.35 mm (3 pcs)
1 x	Copier 2x20 cm pcs
1 x	Spare round blades, 28 mm, pack/ 2 pcs.
1 x	Set brocas Ø 2.0-2.2-2.4-2.6 mm (4 pcs)
1 x	Set fresas corte acero-carburo Ø 1.8/2.3 mm (2 pcs)
1 x	Mini Infrared Thermomiter
1 x	Aramid fibre shears Proton®, 21 cm / 8" length
2 x	Set brocas Ø 1.5-2.0-2.5-3.0 mm (4 pcs)
1 x	HPP-21 PLUS PC Programmer for Hitec Digital Servos
1 x	Mold plugs XT-30
1 x	Modelling compound (Plastilin), sculptor's quality 1 Kg
1 x	Heat Seal Iron
1 x	Tachometer HANGAR 9 digital
1 x	silverlot 45% - 1,50x500 mm solder rods (2 pcs)
1 x	wing/fuselage connector for 16 pines AWG 20-24
1 x	Cable-Tie 1.66x71mm / 0.07x2.8″ (20 pcs)
1 x	Circlick securite
1 x	CC 02
1 x	Copper lacquer wire Ø0,2 mm (5 m)
1 x	PSC 6
1 x	Female prolonguer XH 30 cm 6 cell cable of silicone 0,25 mm
1 x	Prolonguer for Balancer Thunder Power 6S
1 x	Connector CAN 15
1 x	89 mm INO spinner (carbon imitation)
1 x	Spinner INO 89 mm Chrome (Imitacion metal)
1 x	Spinner Alumin. fixed propeller 50 mm / 4,0 mm
1 x	Support conector MPX (6 pcs)
1 x	Support pumb/filter Xicoy X45
1 x	Spinner Alumin. fixed propeller 45 mm / 4,0 mm
1 x	SunCover 110/120/140 Class (SebART)
1 x	Avanti S 2.3m Jet YELLOW/BLACK & retract (SebArt)
1 x	A/C quality beech plywood BIRCH 600x300x1.0 mm
1 x	BALSA triangular 15x15x1000 mm
1 x	Balsa panel 10x100x1000 mm
1 x	Balsa panel 3.0x100x1000 mm
1 x	BALSA triangular 8x8x1000 mm
1 x	BALSA trip 2.0x10.0x1000 mm
1 x	Balsa panel 1.5x100x1000 mm
1 x	Support Filtro FESTO
1 x	Support ECU Xicoy X-45
1 x	Soporte grifo FESTO (2 pcs)
1 x	Spinner INOVA 63 mm White
1 x	Spinner INOVA 102 mm Black
1 x	Spinner INO 57 mm Chrome (Imitacion metal)
1 x	Spinner 82mm Black ventilado
1 x	82 mm INO spinner (carbon imitation)
1 x	F3A carbon 82 mm spinner for 12 mm axis
1 x	Spinner Alumin. fixed propeller 45 mm / 5,0 mm
1 x	Recessed MPX connector support (6 pcs)
1 x	57 mm INO spinner (carbon imitation)
1 x	Aro pasacable Ø25 mm (4 pcs)
1 x	Support Pitot JETI
1 x	Spinner Alumin. fixed propeller 50 mm / 3,2 mm
1 x	Spinner Alumin. fixed propeller 45 mm / 3,2 mm
1 x	F3A carbon 75 mm spinner for Hacker C-50
1 x	45 mm white plastic spinner for fixed propeller / 4,0 mm axi
1 x	Spinner Alumin. fixed propeller 50 mm / 5,0 mm
1 x	102 mm INO spinner (carbon imitation)
1 x	Spinner INO 70 mm Chrome (Imitacion metal)
1 x	75 mm INO spinner (carbon imitation)
1 x	Spinner INO 51 mm Chrome (Imitacion metal)
1 x	Support pump Xicoy X45
1 x	82 mm 12 mm axi 30 g F3A CF drilled spinner
1 x	Pasacables rectangular 40x15 mm (4 pcs)
1 x	51 mm INO spinner (carbon imitation)
1 x	Support Antena 2.4 Ghz (2 pcs)
1 x	38 mm white plastic spinner for fixed propeller / 4,0 mm axi
1 x	82 mm 12 mm axi 30 g F3A CF drilled spinner 3BL
1 x	Tube support Ø 6mm (10 pcs)
1 x	Spinner INO 63 mm Chrome (Imitacion metal)
1 x	Spinner INOVA 45 mm White
1 x	51 mm white plastic spinner for fixed propeller / 4,0 mm axi
1 x	Spinner INO 82 mm Chrome (Imitacion metal)
1 x	Avanti S Jet , Exhaust for JetCat P-140 (SebArt)
1 x	Avanti S 1.8m Jet FREECE TRICOLORI
1 x	Avanti XS Jet , Tricolore Canopy
1 x	Avanti XS Jet , Tank for Keroseno (SebArt)
1 x	Fundas para el transporte F3A alas
1 x	BAE HAWK Mini 1.29m MILITARY ARROW ARF +elec.L.Gear + 3 Microser
1 x	F-104 Starfighter Y/B Aniversary(SebArt)
1 x	Avanti S 1.8m Jet White/Blue
1 x	Receptor MINIMA 6S HITEC
1 x	SPS Remote switch actuator
1 x	SPARK Switch 5.9v
1 x	Opto Gas Engine Kill Switch
1 x	SunCover 2.6 Class (SebART)
1 x	Nose OPTIMA 2.200 mm (Elec or Glider)
1 x	Fresa corte diamante Ø 2.35mm (flame)
1 x	800TVL CMOS camera for FPV
1 x	Premium servo extension 100cm
1 x	290 mm M4 7/8x212 mm shaft ship
1 x	Propeller RABOESCH M4 30 mm (3 Blades) (Left hydropropeller)
1 x	Extension S-Bus 1-2 silicon 30 cm FUTABA
1 x	Propeller RABOESCH M4 40 mm (3 Blades) (Right hydropropeller)
1 x	Cable silicona macho batt. receptor 30 cm (Futaba)
1 x	Cabel "Y" 15 cm
1 x	Extension silicon 100 cm (Graupner)
1 x
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x6.0 mm (5 pcs)
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x4.0 mm (5 pcs)

17,684.02EUR