17.00EUR

Hardener Aero EPH 161 (500 g)
[R11212505]

Hardener Aero EPH 161 (500 g)

Hardener for Epoxy Resin L and L 20, EP Gel coat colourless and Mould Resin P
Contains no formaldehyde and no paraformaldehyde
Epoxy Resin L
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by hot curing for: approx. 10 h at 60 °C
Max. heat distortion temperature after annealing: 120 °C
Laminate structures for vehicle construction in combination with this product and epoxy resin L are approved by the TÜV-Süd. Process instructions/TÜV-Report (unfortunately only in German)
Epoxy Resin L 20
The combination of L 20 and Hardener EPH 161 yields a low-viscosity laminating resin that exhibits superior impregnating and wetting properties to glass, aramid, and carbon fibres. In conjunction with L 20, hardener EPH 161 results in a long service life for the resin compound with very high mechanical and dynamic strengths and perfect curing in both thick (> 2 cm) and thin (1,5 mm) laminates. Before they can obtain the specified mechanical properties, the laminates must be post-cured for about fifteen hours at 60 °C after their initial cold-curing period.
The system L 20 + EPH 161 is approved for the construction of gliders.
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by post-curing: for 15 h at 60 °C
Gel coat colourless
Processing time: 90 minutes
Mixing ratio:
100 : 24 parts by weight EP Gel coat : Hardener EPH 161
Curing time: 24 h at room temperature, afterwards hot curing approx. 10 h/60 °C (recommended, but not necessary).
Max. heat distorsion temperature after annealing: approx. 120 °C
Mould resin P
Processing time: 90 minutes
Mixing ratio:
100 : 17 parts by weight Mould Resin P : Hardener EPH 161
Gelling time: approx. 4 h
Curing time: 24 h at roomtemperature, afterwards hot curing: approx. 15 h/60 °C
Please order resin L and L 20, gel coatcolourless and mould resin P separately

under request

Reviews

Quick Find

Shopping Cart

1 x	Paramotor BackPack XXS 2
1 x	Windsock Ozone L - 700 mm
1 x	Aramid 50 daN 50 m
1 x	Ballast 700gr OPALE
1 x	Trike XL motor set (motor+esc+prop)
1 x	Rescue 1,8m2 / BackPack
1 x	Parachute P4
1 x	Set cintas unión paracaídas 145 cm
1 x	Para-RC Mix
1 x	Paramotor Kit Camo H1.5/ Ben Red
1 x	Windsock Ozone L -1200 mm
2 x	Opale Rucksack
1 x	Para-RC "RC-Evo-Cross" Rescue
1 x	Parachute PV6 for F3J
1 x	Paramotor BackPack XXS (without accessories)
1 x	Connectors banna oro 2 mm (M/F)
1 x	XH male balance (2S) connector (2 pcs)
1 x	XH female balance (2S) connector (2 pcs)
1 x	Connectors banna oro 8,0 mm 5 pcs(Female)
1 x	Conector BEC female (10 pcs)
1 x	EC5-Set male, simple quality, 2 x female pin, 1 x blue housing
1 x	Connector CAN 15
1 x	Optotronix Aurora Plug
2 x	Connectors banna gold 5,5 mm (M/F)
1 x	Connectors banna oro 4 mm (M/F)
1 x	MPX Sub-D Adaptor
1 x	Connectors DEANS (T)
1 x	Banna gold connector 2,5 mm (100 M/F pairs)
1 x	SIMtransmitter 6 Mode 2
3 x	RF9 Flight Simulator with Spektrum Controller
1 x	Interface Jack Adapter IKARUS
1 x	GameCommander USB Universal
1 x	Long ball link M3 (6 uds)
1 x	USB HLS prog. interface
1 x	Straightened rod Ø 3.0 mm x 1000 mm
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x4.0 mm (5 pcs)
1 x	120x60 mm SLH KOVO wheel
1 x	Conector FUTABA Servo female BLUE silicon (10 pcs)
1 x	2 mm female connector (2 pcs) with safety connector
1 x	MR30 connector male
1 x	Connectors MPX male (PIN double)
1 x	30 cm MULTIPLEX female connector
1 x	2 mm male connector (2 pcs) with safety connector
1 x	XH female balance (4S) connector (2 pcs)
1 x	Connectors MPX black male
1 x	Connectors MPX black female
1 x	Wing OXY 0,5 pulgadas2
1 x	Servo KST BLS825 V8.0 HV 35Kg 8.4v
1 x	Servo KST X10-710 V8.0 7.5Kg HV
1 x	Brazo servo aluminio KST 25T-5V2,3515,325,125,135,145X10,X12,A13
1 x	Soporte servo KST X10 mini / DS135MG
1 x	1/7 Pilot "Japanese"
1 x	PVC 0,14 qmm servos wire Hitec/Mpx (5 m)
1 x	Carbon Fabric Prepreg 200 g/m² (twill 2/2) 100 cm, roll/ 1 m
1 x	Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 50 m
1 x	Carbon Non-Woven, 160 g/m² 127 cm 5m
2 x	Simulador RealFlight RF-9.5 S (sin emisora)
1 x	Black silicone 0,25 mm² wire (25 m)
1 x	Connectors MPX female
1 x	3 LiPo XH>EH adapter
1 x	SKY MASTER 3.000 mm ARF
1 x	White silicone 0,25 mm² wire (25 m)
1 x	CARBON CUB FX-3 100-200CC ARF, 165" - 4200 mm (Hangar9)
1 x	Bidule 170 ARF 3.48 m
1 x	PVC 0,25 qmm 4 line servos wire JR/Graupner (5 m)
1 x	Balance "Y" Wire 6S, 2x JST-XH / 1x JST-EH
1 x	PILATUS PC-6 Turbo Porter 33% 5.290 mm
1 x	PVC 0,08 qmm Futaba servos wire (5 m)
1 x	Connectors banna oro 4 mm (M/F) (ultralight)
1 x	Spinner plastic white fixed propeller 42 mm
1 x	40,0 mm hydro-propeller (left hydropropeller)
1 x	40 mm 1/4" Race propeller (rigth hydropropeller)
1 x	Brass rod Ø 1.5 mm x 1000 mm
1 x	Sun Cover PC 21 XXL (JMB Jets)
1 x	Spinner plastic white fixed propeller 30 mm
1 x	Spinner Alumin. fixed propeller 40 mm / 4,0 mm
1 x	45 mm white plastic spinner for fixed propeller
1 x	Beech dowels 2.0 x 1000 mm
1 x	Brass hexagonal rod Ø 4 mm x 1000 mm
1 x	Foam plastic plates (310x210x3 mm)
1 x	28 mm tailwheel unit
1 x	Charger LiPo Charger4
1 x	Foreman, scale 1:32
1 x	TeXtreme® Carbon tape 38 g/m² (IM, unidirectional) 20 mm x 100m
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x2.0 mm (20 pcs)
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x2.0 mm (10 pcs)
1 x	PARTALL® Hi-Temp Wax, 340 g

12,662.70EUR