17.00EUR

Hardener Aero EPH 161 (500 g)
[R11212505]

Hardener Aero EPH 161 (500 g)

Hardener for Epoxy Resin L and L 20, EP Gel coat colourless and Mould Resin P
Contains no formaldehyde and no paraformaldehyde
Epoxy Resin L
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by hot curing for: approx. 10 h at 60 °C
Max. heat distortion temperature after annealing: 120 °C
Laminate structures for vehicle construction in combination with this product and epoxy resin L are approved by the TÜV-Süd. Process instructions/TÜV-Report (unfortunately only in German)
Epoxy Resin L 20
The combination of L 20 and Hardener EPH 161 yields a low-viscosity laminating resin that exhibits superior impregnating and wetting properties to glass, aramid, and carbon fibres. In conjunction with L 20, hardener EPH 161 results in a long service life for the resin compound with very high mechanical and dynamic strengths and perfect curing in both thick (> 2 cm) and thin (1,5 mm) laminates. Before they can obtain the specified mechanical properties, the laminates must be post-cured for about fifteen hours at 60 °C after their initial cold-curing period.
The system L 20 + EPH 161 is approved for the construction of gliders.
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by post-curing: for 15 h at 60 °C
Gel coat colourless
Processing time: 90 minutes
Mixing ratio:
100 : 24 parts by weight EP Gel coat : Hardener EPH 161
Curing time: 24 h at room temperature, afterwards hot curing approx. 10 h/60 °C (recommended, but not necessary).
Max. heat distorsion temperature after annealing: approx. 120 °C
Mould resin P
Processing time: 90 minutes
Mixing ratio:
100 : 17 parts by weight Mould Resin P : Hardener EPH 161
Gelling time: approx. 4 h
Curing time: 24 h at roomtemperature, afterwards hot curing: approx. 15 h/60 °C
Please order resin L and L 20, gel coatcolourless and mould resin P separately

under request

Reviews

Quick Find

Shopping Cart

1 x	ABS tube 6.0x5.0x1000 mm
3 x	ABS tube 12.0x10.0x1000 mm
1 x	Carbon tube (L 1000 mm, Ø2 mm, Ø1 mm)
5 x	ABS tube 8.0x7.0x1000 mm
2 x	Carbon tube (L 1000 mm, Ø22 mm, Ø21 mm)
3 x	ABS tube 9.0x8.0x1000 mm
1 x	Carbon tube (L 1000 mm, Ø12 mm, Ø10 mm)
2 x	ABS tube 14.0x10.0x1000 mm
2 x	ABS tube 7.0x5.0x1000 mm
1 x	Aluminium tube (L 1000 mm, Ø5.0 mm, Ø4.1 mm)
2 x	ABS tube 5.0x3.0x1000 mm
1 x	ABS tube 9.0x7.0x1000 mm
2 x	Aluminium tube (L 1000 mm, Ø3.0 mm, Ø2.1 mm)
2 x	ABS tube 3.0x2.0x1000 mm
3 x	ABS tube 3.0x1.0x1000 mm
2 x	Aluminium tube (L 1000 mm, Ø7.0 mm, Ø6.1 mm)
3 x	Aluminium tube (L 1000 mm, Ø4.0 mm, Ø3.1 mm)
3 x	ABS tube 8.0x6.0x1000 mm
2 x	ABS tube 3.0x2.0x330 mm
3 x	ABS tube 4.0x2.0x1000 mm
2 x	ABS tube 10.0x8.0x1000 mm
1 x	Carbon tube (L 1000 mm, Ø16 mm, Ø14 mm)
2 x	ABS tube 4.0x3.0x1000 mm
2 x	Carbon tube (L 1000 mm, Ø16 mm, Ø12 mm)
4 x	ABS tube 6.0x4.0x1000 mm
1 x	CF tube (L 1000 mm, Ø1 mm, Ø0,5 mm)
2 x	CF tube (L 1000 mm Ø0,7 mm, Ø0,3 mm)
2 x	ABS tube 18.0x16.0x1000 mm
1 x	Hard brass tubing (L 1000 mm, Ø5.0 mm, Ø4.1 mm)
1 x	Hard brass tubing (L 1000 mm, Ø2.0 mm, Ø1.2 mm)
2 x	Fiberglass tube 6/4x1000mm
2 x	Hard brass tubing (L 1000 mm, Ø6.0 mm, Ø5.2 mm)
2 x	ABS tube 20.0x18.0x1000 mm
1 x	Camera Sony 4140+673 CCD with Built-in 200mw TX + antenna
1 x	USB Mini Camera endoscope
1 x	Steel tube (L 1000 mm Ø9 mm, Ø8,7 mm)
1 x	Steel tube (L 1000 mm Ø4 mm, Ø3,7 mm)
1 x	Steel tube (L 1000 mm Ø8 mm, Ø7,7 mm)
2 x	Strip ABS 2.0x10.0x1000 mm
2 x	Round Rod 4,0x1000 mm
2 x	ABS Strip 1.5x3.0x1000 mm
1 x	Steel tube (L 1000 mm Ø7 mm, Ø6,7 mm)
1 x	CF tube set (Ø 38 mm y Ø 14 mm)
1 x	Steel tube (L 1000 mm Ø6 mm, Ø5,7 mm)
3 x	Strip ABS 2.0x3.0x1000 mm
1 x	Steel tube (L 1000 mm Ø12 mm, Ø11,7 mm)
1 x	Steel tube (L 1000 mm Ø10 mm, Ø9,7 mm)
1 x	Round Rod 6,0x1000 mm
1 x	ABS Strip 1.5x8.0x1000 mm
1 x	ABS Strip 1.0x5.0x1000 mm
1 x	ABS Strip 1.5x2.0x1000 mm
1 x	Strip 3,5x1,75x330 mm
1 x	Motor DLE 430 cc - Paramotors
2 x	Small Crow DLE-170M
1 x	Big Crow DLE-170M
1 x	Optotronix Aurora Plug
1 x	Banna gold connector 2,5 mm (100 M/F pairs)
1 x	Connectors DEANS 4 pins (1 pair)
1 x	Connectors banna oro 6,0 mm (M/F)
2 x	Banna gold connector 2,5 mm (M/F)
1 x	Connectors banna oro 3 mm (M/F)
1 x	Connectors banana oro 6,0 mm Ultralight (M/F)
1 x	XH male balance (4S) connector (2 pcs)
1 x	XH male balance (2S) connector (2 pcs)
1 x	30 cm DEANS female connector
1 x	XH female balance (2S) connector (2 pcs)
1 x	Connectors banna oro 2 mm (M/F)
1 x	XH female balance (5S) connector (2 pcs)
1 x	XH female balance (3S) connector (2 pcs)
1 x	2 mm female connector (2 pcs) with safety connector
1 x	XH female balance (4S) connector (2 pcs)
1 x	Conector BEC male (10 pcs)
1 x	Conector AS150 7mm antichispazo (Set: 2 pares)
1 x	Gold antispark 5,5 mm plug
1 x	Connectors banna oro 2 mm (M/F) (ultralight)
1 x	Propeller POWER-PROP 13x9 Izda
1 x	Straightened rod Ø 1.5 mm x 1000 mm
1 x	Prolongador S-Bus JR/JR 10cm
1 x	Ball link V1 Ø7 M4/3 (6 uds)
1 x	Carbon tube 3K (L 1000 mm, Ø 8 mm, Ø 7 mm)
1 x	30 cm BEC cable (male)
2 x	Carbon tube 3K-PW (L 1000 mm, Ø12 mm, Ø8 mm)
1 x	Nylon hinge 15x0,3 (10 pcs)
1 x	Carbon tube (L 1000 mm, Ø12 mm, Ø10 mm)
1 x	Rigid coupling brass Ø 4 mm L: 25 mm
1 x	Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 100 m
1 x	Foaming agent for epoxy resins 200 g
1 x	Carbon roving DowAksa / 24k / 1600 tex
1 x	Cyanoacrylate MD GLUE plus 405, for extreme loads 20g
1 x	Servo Arm aluminium ALU-STAR
1 x	Connectors banna oro 3,5 mm (M/F)
1 x	Connectors MPX female (PIN double)
2 x	Carbon tube 3K-PW (L 2000 mm, Ø20 mm, Ø18 mm)
1 x	PS-050 TONEGAWA Servo
1 x	ABS tube 16.0x14.0x1000 mm
1 x	Carbon tube (L 1000 mm, Ø18 mm, Ø15 mm)
1 x	Carbon tube 3K-PW (L 1000 mm, Ø22 mm, Ø20 mm)
1 x	Carbon tube 3k-LW (L 2000 mm, Ø30 mm, Ø26 mm)
1 x	Servo inverter
1 x	Adjustable launching hook
1 x	Carbon tube 3K-PW (L 1000 mm, Ø20 mm, Ø18 mm)
1 x	Carbon tube (L 1000 mm, Ø4 mm, Ø2,5 mm)
1 x	ABS tube 5.0x4.0x156 mm
1 x	Carbon tube (L 2000 mm, Ø16 mm, Ø14 mm)
1 x	Towing hook <3m
1 x	Servo Tester
1 x	Carbon tube 3K-PW (L 1000 mm, Ø40 mm, Ø36 mm)
1 x	Carbon tube (L 1000 mm, Ø3 mm, Ø2 mm)
1 x	Carbon tube (L 1000 mm, Ø6 mm, Ø4 mm)
1 x	Hard brass tubing (L 1000 mm, Ø4.0 mm, Ø3.1 mm)
1 x	Carbon tube 3K-PW (L 2000 mm, Ø40 mm, Ø36 mm)
1 x	ABS Strip 1.0x2.0x1000 mm
1 x	Hard brass tubing (L 1000 mm, Ø10.0 mm, Ø9.1 mm)
1 x	Strip 1,5x1,5x330 mm
1 x	Round Rod 1,25x1000 mm
1 x	Strip ABS 2.0x5.0x1000 mm
1 x	RX external cable for estandar receivers
1 x	Strip 2,0x2,0x330 mm
2 x	ABS I Strip 10x5x1000 mm
2 x	Motor DLE 170 M- Paramotors
1 x	Carbon tube 3K-PW (L 2000 mm, Ø14 mm, Ø12 mm)
1 x	PBS TJ 40-G1 Turbine
2 x	ABS Strip 1.5x4.0x1000 mm
1 x	Motor DLE 200cc Std
1 x	Round Rod 1,0x1000 mm
2 x	ABS Strip 1.5x6.0x1000 mm
2 x	ABS Strip 1.0x3.0x1000 mm
1 x	Hard brass tubing (L 1000 mm, Ø7.0 mm, Ø6.1 mm)
1 x	Carbon tube 3K-PW (L 1000 mm, Ø30 mm, Ø27 mm)
1 x	Round Rod 2,0x1000 mm
1 x	ABS I Strip 20x10x1000 mm
1 x	MPX screwable clips (4 pcs)
1 x	Wing conexion 2 servos JR/Graupner 50 cm
1 x	XH male balance (5S) connector (2 pcs)
1 x	XT-30 connector (pair)
1 x	Connectors DEANS (T) micro
1 x	Conector FUTABA Servo male BLUE silicon (10 pcs)
1 x	Wing connector 8pin with pin strip, plug & socket
1 x	PIN Connector female (100 pcs)
1 x	Conector XT-150 6mm (Set: 5 pares)
1 x	XH male balance (3S) connector (2 pcs)
1 x	MPX PCB "6 Pins", 5 pieces
1 x	45 mm black plastic spinner for fixed propeller
1 x	Spinner INO 89 mm Chrome (Imitacion metal)
1 x	White gelcoat 1 Kg
1 x	Release wax 250ml
1 x	42 mm white plastic spinner for fixed propeller
1 x	Spinner Alumin. fixed propeller 50 mm / 6,0 mm
1 x	Spinner plastic red fixed propeller 30 mm
1 x	Hardener Aero EPH 161 (500 g)
1 x	Falcon Carbon Spinner 82mm for electric motor
1 x	50 mm white plastic spinner for fixed propeller
1 x	Carbon fiber rod 2.0 mmx1000 mm
1 x	Carbon tube 3K-PW (L 2000 mm, Ø40 mm, Ø37 mm)
1 x	Hitec 52 mm servo arm
1 x	Hitec 30 mm servo rounded arm
1 x	Futaba 76/92 mm servo pull-pull double arm with ball link HUB Al
1 x	Futaba 14/20 mm servo pull-pull double arm with ball link
1 x	Mould Resin P + Hardener EPH 161-P, kit/ 585 g
1 x	F3A carbon 82 mm spinner for 12 mm axis
1 x	Mould Resin P 10 kg
1 x	Thixotropic agent TM 100, tin/ 415 g (approx. 5 l)
1 x	51 mm white plastic spinner for fixed propeller / 4,0 mm axi
1 x	Latex Gloves GRIP, size L, box/ 100 pcs
1 x	Spinner Alumin. fixed propeller 45 mm / 4,0 mm
1 x	63 mm INO spinner (carbon imitation)
1 x	Wooden mouth spatulas (150 x 18 x 1.5 mm), 100 pcs

31,880.14EUR