17.00EUR

Hardener Aero EPH 161 (500 g)
[R11212505]

Hardener Aero EPH 161 (500 g)

Hardener for Epoxy Resin L and L 20, EP Gel coat colourless and Mould Resin P
Contains no formaldehyde and no paraformaldehyde
Epoxy Resin L
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by hot curing for: approx. 10 h at 60 °C
Max. heat distortion temperature after annealing: 120 °C
Laminate structures for vehicle construction in combination with this product and epoxy resin L are approved by the TÜV-Süd. Process instructions/TÜV-Report (unfortunately only in German)
Epoxy Resin L 20
The combination of L 20 and Hardener EPH 161 yields a low-viscosity laminating resin that exhibits superior impregnating and wetting properties to glass, aramid, and carbon fibres. In conjunction with L 20, hardener EPH 161 results in a long service life for the resin compound with very high mechanical and dynamic strengths and perfect curing in both thick (> 2 cm) and thin (1,5 mm) laminates. Before they can obtain the specified mechanical properties, the laminates must be post-cured for about fifteen hours at 60 °C after their initial cold-curing period.
The system L 20 + EPH 161 is approved for the construction of gliders.
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by post-curing: for 15 h at 60 °C
Gel coat colourless
Processing time: 90 minutes
Mixing ratio:
100 : 24 parts by weight EP Gel coat : Hardener EPH 161
Curing time: 24 h at room temperature, afterwards hot curing approx. 10 h/60 °C (recommended, but not necessary).
Max. heat distorsion temperature after annealing: approx. 120 °C
Mould resin P
Processing time: 90 minutes
Mixing ratio:
100 : 17 parts by weight Mould Resin P : Hardener EPH 161
Gelling time: approx. 4 h
Curing time: 24 h at roomtemperature, afterwards hot curing: approx. 15 h/60 °C
Please order resin L and L 20, gel coatcolourless and mould resin P separately

under request

Reviews

Quick Find

Shopping Cart

2 x	Round Rod 1,25x1000 mm
2 x	Strip ABS 2.0x10.0x1000 mm
2 x	Round Rod 2,0x1000 mm
2 x	ABS Strip 1.5x3.0x1000 mm
1 x	Strip 3,5x1,75x330 mm
2 x	ABS Strip 1.5x2.0x1000 mm
2 x	Strip ABS 2.0x3.0x1000 mm
1 x	ABS I Strip 10x5x1000 mm
2 x	ABS Strip 1.5x6.0x1000 mm
3 x	Strip ABS 2.0x8.0x1000 mm
3 x	Round Rod 6,0x1000 mm
3 x	Round Rod 1,5x1000 mm
1 x	Strip 2,5x1,25x330 mm
3 x	Strip 1,5x1,5x330 mm
2 x	Round Rod 2,5x1000 mm
2 x	ABS Strip 1.0x3.0x1000 mm
1 x	Round Rod 4,0x1000 mm
2 x	ABS Strip 1.5x4.0x1000 mm
2 x	ABS I Strip 20x10x1000 mm
1 x	Strip ABS 2.0x5.0x1000 mm
2 x	Strip 2,0x2,0x330 mm
2 x	Round Rod 3,0x1000 mm
2 x	ABS Strip 1.0x4.0x1000 mm
1 x	ABS Strip 1.0x5.0x1000 mm
4 x	ABS Strip 1.5x8.0x1000 mm
1 x	Round Rod 1,0x1000 mm
1 x	Round Rod 5,0x1000 mm
1 x	ABS Strip 1.0x2.0x1000 mm
1 x	SE Ring HACKER 300 mm (2 pcs)
2 x	SE Ring 330 mm (4 pcs)
2 x	Ring 320 mm length (5 pcs)
2 x	13 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	20x1000 mm Ring Strap Back To Back
1 x	SE Ring 350 mm (2 pcs)
1 x	Pad Screw Mount M3, up to 3mm / 0.12″, (10 pcs)
1 x	Pilot "Anthony" (Slimline)
1 x	Civilian pilot "Pamela" size 9cm (Slimline)
1 x	1/6 Pilot "Garry"
2 x	Pilot "Duke" Legends Series (Slimline)
1 x	Servo NARO Max Std
1 x	Pilot WWII US Navy Pacific 12" Scale 1/6-1/5
2 x	Civilian pilot "Gramps" size 9cm (Slimline)
2 x	1/12 Pilot "Tom"
1 x	Pilot "Adolf" Legends Series (Slimline)
1 x	Hovercraft sailcloth
1 x	Pilot "Goose" (Slimline)
2 x	1/6 Pilot "Buddy"
3 x	1/10 Pilot "Jimmy"
1 x	Civilian pilot "G-Man" size 9cm (Slimline)
3 x	1/4 Pilot "Heidi"
1 x	1/6 Pilot "Tony"
1 x	Piloto Jet "Red" 1/6 Scale
2 x	1/12 Pilot "Fighter"
1 x	2000A 12V Lithium Jump Starter with 150PSI Air inflator
1 x	1/10 Pilot "Jack"
1 x	1/4 Pilot "Mike"
2 x	Pilot "Dick" Legends Series (Slimline)
2 x
1 x	Pilot JAN 1/4 Saiplanes
1 x	Piloto Jet "Green" 1/6 Scale
1 x	Smoke set "S"
1 x	ABS tube 6.0x4.0x1000 mm
1 x	Parachute BACKUP X100
1 x	ABS tube 16.0x14.0x1000 mm
1 x	Kwik link AL M2,5 L:23 mm (2 pcs) + Pin Ø 1,6 mm
1 x	Angled clevis with threaded rod M3
1 x	BALSA trip 3.0x3.0x1000 mm
1 x	Banna gold connector 2,5 mm (100 M/F pairs)
1 x	Aluminium wide washer M4 Blue (4 pcs)
1 x	Fast'n EZ-CA-Hinge, lite (12 uds)
1 x	Balls 4 mm
1 x	Complete kit CAT 966G II WEDICO-construction-models
2 x	Sun Cover BULL Mo1 2.6 (Hispano Aviacion)
1 x	SE Ring 250 mm (2 pcs)
1 x	Tape GFK 50 mm
1 x	Waterproof adhesive tape, width 19mm, length 25m
1 x	10 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x	Marker ties (20 pcs)
1 x	SE Ring 240 mm (2 pcs)
1 x	Digital Air Speed Sensor And Pitot Tube Set
1 x	Tube Pitot to PIXHAWK
1 x	Carbon fiber rod 3.0 mm x 1000 mm
1 x	Carbon fiber rod 0.5 mmx1000 mm
1 x	Field folding model stand SebArt
2 x	Cinta Goldfix 1m
1 x	Spikes Band (5 m)
1 x	SE Ring 400 mm (2 pcs)
1 x	3,2 mm Prop Adapter M8
1 x	6 mm Prop Adapter M8
1 x	3.2 mm Prop Adapter M8
2 x	Civilian pilot "Joe" size 9cm (Slimline)
1 x	3,2 mm Prop Adapter M6
1 x	Prop Shaft Adapter 5 mm "long"
1 x	PT 21x13 EL Propeller
1 x	PT 20x13 EL Propeller
1 x	PT 16x10 E Propeller
1 x	PT 21x13 EL Propeller 3 Blade
1 x	Cable-Tie 1.66x71mm / 0.07x2.8″ (20 pcs)
1 x	DPSI Ampere & Voltage bundle
1 x	Propeller POWER-PROP 14x9 Izda
1 x	CA Glue (medium) 20g
1 x	SE Ring 200 mm (2 pcs)
1 x	Spinner fixed propeller 60 mm / 5,0 mm
1 x	20x200 mm battery rings
1 x	Foil for sticking flaps and ailerons
1 x	DPSI Micro-DualBat 5.9V / 7.2V MPX-JR
1 x	wing/fuselage connector for 6 pines AWG 20-24 (without pines)
1 x	DPSI Ampere battery backer
1 x	FesEx-Uni6 System
1 x	Alu-Cross for Backmount of A60-V2-Backmountmotors
1 x	Connectors banna oro 8,0 mm (Male) 5 pcs.
1 x	Battery LiFe TopFuel 3100 mAh 3s MTAG 30C
1 x	Civilian pilot "Curt" size 9cm (Slimline)
1 x	Carbon Fabric Prepreg 200 g/m² (twill 2/2) 100 cm, roll/ 1 m
1 x
1 x	ARAMID honeycomb 1300x2600x2 mm
1 x	Wing-connector: Glass / Carbon tube (13.7/12.5) x 1000 mm
1 x	Carbon roving DowAksa / 24k / 1600 tex
1 x	Mixing tube for double syringes and cartridges (MR 1:1 and 2:1)
1 x	Hardener Aero EPH 161 (500 g)
1 x	Carbon fibre tape 200 g/m² (unidirectional) 50 mm
1 x	Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 100 m
1 x	Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 20 m

9,757.81EUR