17.00EUR

Hardener Aero EPH 161 (500 g)
[R11212505]

Hardener Aero EPH 161 (500 g)

Hardener for Epoxy Resin L and L 20, EP Gel coat colourless and Mould Resin P
Contains no formaldehyde and no paraformaldehyde
Epoxy Resin L
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by hot curing for: approx. 10 h at 60 °C
Max. heat distortion temperature after annealing: 120 °C
Laminate structures for vehicle construction in combination with this product and epoxy resin L are approved by the TÜV-Süd. Process instructions/TÜV-Report (unfortunately only in German)
Epoxy Resin L 20
The combination of L 20 and Hardener EPH 161 yields a low-viscosity laminating resin that exhibits superior impregnating and wetting properties to glass, aramid, and carbon fibres. In conjunction with L 20, hardener EPH 161 results in a long service life for the resin compound with very high mechanical and dynamic strengths and perfect curing in both thick (> 2 cm) and thin (1,5 mm) laminates. Before they can obtain the specified mechanical properties, the laminates must be post-cured for about fifteen hours at 60 °C after their initial cold-curing period.
The system L 20 + EPH 161 is approved for the construction of gliders.
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by post-curing: for 15 h at 60 °C
Gel coat colourless
Processing time: 90 minutes
Mixing ratio:
100 : 24 parts by weight EP Gel coat : Hardener EPH 161
Curing time: 24 h at room temperature, afterwards hot curing approx. 10 h/60 °C (recommended, but not necessary).
Max. heat distorsion temperature after annealing: approx. 120 °C
Mould resin P
Processing time: 90 minutes
Mixing ratio:
100 : 17 parts by weight Mould Resin P : Hardener EPH 161
Gelling time: approx. 4 h
Curing time: 24 h at roomtemperature, afterwards hot curing: approx. 15 h/60 °C
Please order resin L and L 20, gel coatcolourless and mould resin P separately

under request

Reviews

Quick Find

Shopping Cart

1 x	MAX pilot ARTF
1 x	Windsock Ozone L - 700 mm
1 x	LUCAS pilot ARTF
2 x	Windsock Ozone L -1200 mm
1 x	Paramotor BackPack XXS (without accessories)
1 x	Paramotor Kit Camo H1.5/ Ben Red
1 x	Opale Rucksack
1 x	Para-RC Trike "RC-Bullix"
1 x	Wing OXY 0,5 pulgadas2
1 x	Ballast 700gr OPALE
1 x	Aramid 50 daN 50 m
1 x	Wing OXY 5,0 m2
1 x	Para-RC Mix
1 x	Paramotor Trike XL
1 x	Rescue 1,8m2 / BackPack
1 x	Propeller APC 12x6 Electric Pusher
1 x	Flat washer 1.7 mm (20 pcs)
1 x	Propeller APC 10x6 Electric
1 x	Propeller 9x7 SlowFlyer
1 x	Propeller APC 11x10 Electric
1 x	Propeller APC 10x10 Electric
1 x	Connectors banna oro 8,0 mm (Male) 5 pcs.
1 x	Marker ties (20 pcs)
1 x	Hardener Aero EPH 161 (500 g)
1 x	Connectors banna oro 2 mm (M/F)
1 x	Glass fabric tape 225 g/m² (Silane, plain) 30 mm X 100m
1 x	Cable-Tie 1.66x71mm / 0.07x2.8″ (20 pcs)
1 x	Vacuum bag, 1200 mm x 50 m
1 x	Spikes Band (5 m)
1 x	XH female balance (4S) connector (2 pcs)
1 x	Connectors banna oro 4 mm (M/F) (ultralight)
1 x	Cyanoacrylate MD GLUE plus 405, for extreme loads 20g
1 x	Connectors banna oro 2 mm (M/F) (ultralight)
1 x	XH female balance (3S) connector (2 pcs)
1 x	Banna gold connector 2,5 mm (M/F)
1 x	Pad self adhesive, up to 3mm / 0.12″, (10 pcs)
1 x	Connector CAN 15
1 x	Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 10 m
1 x	Gold antispark 4 mm plug
1 x	SE Ring 480 mm (2 pcs)
1 x	Wing-connector: Glass / Carbon tube (26.5/25 x 25/23) x 1000 mm
1 x	Connectors banna oro 0,8 mm (M/F)
1 x	ABS "T" angle 6.0x6.0x1000 mm
1 x	Cable servo PREMIUM 1 m (blanco/rojo/negro) AWG21 + AWG26 TPE
1 x	Ball link duraluminium M3 V1 (10 pcs)
1 x	Ball link Aluminio M4 x 4 x 6 x 26mm (4 uds)
1 x	Balanceradapter JST-XH (Heli 47G) 2-6 c.
1 x	Cabel PVC 2 x 0.25 mm2 (5 m) red-black
1 x	Red copper lacquer wire Ø0,2 mm (5 m)
1 x	Profile ABS half cane 2.5x1000 mm
1 x	CC 03
1 x	L-Connector 1.0 mm x 1000 mm
1 x	Silicone 0,50 qmm servos wire Graupner(5 m)
1 x	Threaded coupler M2,5 Ø 2 mm (10 pcs)
1 x	PVC 0,14 qmm servo wire Futaba (5 m)
1 x	Tow hook for tug
1 x	Towing hook
1 x	2 LiPo XH>EH adapter
1 x	Balance "Y" Wire 6S, 2x JST-XH / 1x JST-EH
1 x	U Profile ABS 5,0x10,0x1000 mm
1 x	Towing hook
1 x	3 copper lacquer wire Ø0,2 mm (1 m)
1 x	Aluminium blue ball links M3 V1 (10 pcs)
1 x	Cabel charger transmitter GRAUPNER
1 x	3,2 mm Prop Adapter M6
1 x	3,2 mm Prop Adapter M6
1 x	PropCover 16-20" (2 pcs)
1 x	Parachute PV6 for F3J
1 x	Quicklock washer 2.5 mm (10 pcs)
1 x	Propeller APC 10x4.7
1 x	Propeller APC 11x5.5 Electric Pusher
1 x	Propeller APC 11x7 SF
1 x	Propeller APC 10x5 Electric Pusher
1 x	Propeller 3x2
1 x	Propeller APC 11x4.7 SF Pusher
1 x	Propeller APC 11x7 Electric
1 x	Quicklock washer 3 mm (10 pcs)
1 x	Propeller APC 10x4.7 SF
1 x	Lock washer 4.3 mm (20 pcs)
1 x	Propeller APC 10x7 SF
1 x	Aluminium cap bolt washer M4 red (8 pcs)
1 x	Pad Screw Mount M3, up to 3mm / 0.12″, (10 pcs)
1 x	Connectors DEANS 4 pins (1 pair)
1 x	CA Glue fast 20g
1 x	26 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
1 x	SE Ring 240 mm (2 pcs)

4,193.89EUR