11.00EUR

Hardener Aero EPH 161 (250 g)
[R1121250]

Hardener Aero EPH 161 (250 g)

Hardener for Epoxy Resin L and L 20, EP Gel coat colourless and Mould Resin P
Contains no formaldehyde and no paraformaldehyde
Epoxy Resin L
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by hot curing for: approx. 10 h at 60 °C
Max. heat distortion temperature after annealing: 120 °C
Laminate structures for vehicle construction in combination with this product and epoxy resin L are approved by the TÜV-Süd. Process instructions/TÜV-Report (unfortunately only in German)
Epoxy Resin L 20
The combination of L 20 and Hardener EPH 161 yields a low-viscosity laminating resin that exhibits superior impregnating and wetting properties to glass, aramid, and carbon fibres. In conjunction with L 20, hardener EPH 161 results in a long service life for the resin compound with very high mechanical and dynamic strengths and perfect curing in both thick (> 2 cm) and thin (1,5 mm) laminates. Before they can obtain the specified mechanical properties, the laminates must be post-cured for about fifteen hours at 60 °C after their initial cold-curing period.
The system L 20 + EPH 161 is approved for the construction of gliders.
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by post-curing: for 15 h at 60 °C
Gel coat colourless
Processing time: 90 minutes
Mixing ratio:
100 : 24 parts by weight EP Gel coat : Hardener EPH 161
Curing time: 24 h at room temperature, afterwards hot curing approx. 10 h/60 °C (recommended, but not necessary).
Max. heat distorsion temperature after annealing: approx. 120 °C
Mould resin P
Processing time: 90 minutes
Mixing ratio:
100 : 17 parts by weight Mould Resin P : Hardener EPH 161
Gelling time: approx. 4 h
Curing time: 24 h at roomtemperature, afterwards hot curing: approx. 15 h/60 °C
Please order resin L and L 20, gel coatcolourless and mould resin P separately

under request

Reviews

Quick Find

Shopping Cart

1 x	Connectors banna oro 2 mm (M/F) (ultralight)
1 x	Connectors banna gold 5,5 mm (M/F)
1 x	XH female balance (2S) connector (2 pcs)
1 x	XH male balance (5S) connector (2 pcs)
1 x	Connectors DEANS 4 pins (1 pair)
1 x	Connectors banna oro 6,0 mm (M/F)
1 x	Gold antispark 5,5 mm plug
1 x	Connectors banna oro 2 mm (M/F)
1 x	Connectors banna oro 3 mm (M/F)
1 x	Connector CAN 15
1 x	Wing connector 8pin with pin strip, plug & socket
1 x	Connectors banana oro 6,0 mm Ultralight (M/F)
1 x	Conector Servo female 4 pines
1 x	2 mm female connector (2 pcs) with safety connector
1 x	Banna gold connector 2,5 mm (100 M/F pairs)
1 x	Connectors banna oro 0,8 mm (M/F)
2 x	Connectors DEANS (T)
1 x	EC5-Set female, simple quality, 2 x female pin, 1 x blue housing
1 x	XH male balance (4S) connector (2 pcs)
1 x	XH male balance (2S) connector (2 pcs)
1 x	Conector AS150 7mm antichispazo (Set: 2 pares)
2 x	XH female balance (3S) connector (2 pcs)
1 x	Optotronix Aurora Plug
1 x	XH female balance (5S) connector (2 pcs)
1 x	XH female balance (4S) connector (2 pcs)
2 x	Connectors banna oro 8,0 mm (Male) 5 pcs.
2 x	MPX Sub-D Adaptor
1 x	Connectors banna oro 8,0 mm (M/F)
1 x	Connectors banna oro 4 mm (M/F) (ultralight)
1 x	Connectors banna oro 3,5 mm (M/F)
1 x	DYNAMOMETER S-1580
2 x	SERVO HOLDER
1 x	Towing hook
1 x	Towing hook
2 x	SIMtransmitter 6 Mode 2
3 x	Simulador RealFlight RF-9.5 S (sin emisora)
1 x	RF9 Flight Simulator with Spektrum Controller
1 x	Wing-connector: Glass / Carbon tube (13.7/12.5) x 1000 mm
1 x	Civilian pilot "Joe" size 9cm (Slimline)
1 x	PVC 0,08 qmm Futaba servos wire (5 m)
1 x	Steel tube (L 1000 mm Ø8 mm, Ø7,7 mm)
1 x	Dust collector for mould cleaning
1 x	Pine wood slat 6.0x6.0x1000 mm
1 x	Balance "Y" Wire 7S, 2x JST-XH / 1x JST-EH
1 x	TrainerCord (master-learner)
1 x	Brass control horn M3 short for wire (2 pcs)
1 x	Threaded coupler ALU M3 Ø 5 (2 uds)
1 x	Round Rod 6,0x1000 mm
1 x	ABS Strip 1.0x4.0x1000 mm
1 x	48 x 10 mm cylidric hinge Ø 3,0 mm (10 pcs)
1 x	Propeller POWER-PROP 7x7
1 x	Retract undercarriage for gliders 3-7 Kg 3.8-4.3 (without wheel)
1 x	Glider retract undercarriage 8-16 Kg 2.5-3.2(127 mm wheel)
1 x	SU 29S 140 carbon landing gear
1 x	XH male balance (8S) connector (2 pcs)
1 x	Soporte carbono MR30 (2 pcs)
1 x	XH male balance (9S) connector (2 pcs)
1 x	Dual Sequencer Gear and Canopy
1 x	Nylon threaded block M6 (2 uds)
1 x	Tailwheel for 1-3 kg models
1 x	Landing gear clamp for Ø 2 mm (4 uds)
1 x	Connectors MPX female
1 x	MR30 connector female
1 x	Contacto macho pin conector (10 pcs)
1 x	Red 3m5 mm connector holder
1 x	Connectors MPX 8 pins with support (black) 1 pair (male-female)
1 x	Connectors MPX male (PIN double)
1 x	MPX Support (2 pcs)
1 x	30 cm DEANS female connector
1 x	Banna gold connector 2,5 mm (M/F)
1 x	Mounting frame MPX female connector
1 x	Optical RPM Sensor
1 x	1/12 Pilot "Tom"
1 x	2 mm male connector (2 pcs) with safety connector
2 x	EasyFLY Addon
1 x	Carbon tube (L 1000 mm, Ø1.5 mm, Ø0.7 mm)
1 x	Carbon tube (L 1000 mm, Ø12 mm, Ø10 mm)
1 x	ABS tube 4.0x3.0x1000 mm
1 x	Carbon tube (L 1000 mm, Ø12 mm, Ø10 mm)
1 x	OS 40-FG 4T Motor
1 x	Slave-cable USB Easy Sim
1 x	X-RAY Micro QR (Rudder)

3,385.34EUR