11.00EUR

Hardener Aero EPH 161 (250 g)
[R1121250]

Hardener Aero EPH 161 (250 g)

Hardener for Epoxy Resin L and L 20, EP Gel coat colourless and Mould Resin P
Contains no formaldehyde and no paraformaldehyde
Epoxy Resin L
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by hot curing for: approx. 10 h at 60 °C
Max. heat distortion temperature after annealing: 120 °C
Laminate structures for vehicle construction in combination with this product and epoxy resin L are approved by the TÜV-Süd. Process instructions/TÜV-Report (unfortunately only in German)
Epoxy Resin L 20
The combination of L 20 and Hardener EPH 161 yields a low-viscosity laminating resin that exhibits superior impregnating and wetting properties to glass, aramid, and carbon fibres. In conjunction with L 20, hardener EPH 161 results in a long service life for the resin compound with very high mechanical and dynamic strengths and perfect curing in both thick (> 2 cm) and thin (1,5 mm) laminates. Before they can obtain the specified mechanical properties, the laminates must be post-cured for about fifteen hours at 60 °C after their initial cold-curing period.
The system L 20 + EPH 161 is approved for the construction of gliders.
Processing time: 90 minutes
Mixing ratio:
100 : 25 parts by weight of resin to hardener
100 : 29 parts by volume of resin to hardener
Curing time: 24 h at room temperature, followed by post-curing: for 15 h at 60 °C
Gel coat colourless
Processing time: 90 minutes
Mixing ratio:
100 : 24 parts by weight EP Gel coat : Hardener EPH 161
Curing time: 24 h at room temperature, afterwards hot curing approx. 10 h/60 °C (recommended, but not necessary).
Max. heat distorsion temperature after annealing: approx. 120 °C
Mould resin P
Processing time: 90 minutes
Mixing ratio:
100 : 17 parts by weight Mould Resin P : Hardener EPH 161
Gelling time: approx. 4 h
Curing time: 24 h at roomtemperature, afterwards hot curing: approx. 15 h/60 °C
Please order resin L and L 20, gel coatcolourless and mould resin P separately

under request

Reviews

Quick Find

Shopping Cart

1 x	Flat washer 1.7 mm (20 pcs)
1 x	Flat washer 2.2 mm (20 pcs)
1 x	Aluminium wide washer M4 Gold (4 pcs)
1 x	Quicklock washer 1 mm (10 pcs)
1 x	Flat washer 4.3 mm (20 pcs)
1 x	Aluminium cap bolt washer M4 red (8 pcs)
1 x	Lock washer 2.7 mm (20 pcs)
1 x	Quicklock washer 3.5 mm (10 pcs)
1 x	Spring lock washer 2.6 mm (20 pcs)
1 x	Lock washer 4.3 mm (20 pcs)
1 x	Spring lock washer 2.1 mm (20 pcs)
1 x	Circlik for shaft 1.9 mm (10 pcs)
1 x	Aluminium cap bolt washer M3 green (8 pcs)
1 x	Quicklock washer 3 mm (10 pcs)
1 x	Quicklock washer 2.5 mm (10 pcs)
1 x	Lock washer 2.2 mm (20 pcs)
1 x	Aluminium wide washer M3 blue (4 pcs)
1 x	Circlik for shaft 1.2 mm (10 pcs)
1 x	Aluminium wide washer M3 gold (4 pcs)
1 x	Spring lock washer 3.1 mm (20 pcs)
1 x	M3-M4 rubber washer (8 pcs)
1 x	Aluminium cap bolt washer M3 blue (8 pcs)
1 x	Aluminium wide washer M3 red (4 pcs)
1 x	Aluminium wide washer M4 Red (4 pcs)
1 x	Circlik for shaft 1.5 mm (10 pcs)
1 x	Lock washer 3.2 mm (20 pcs)
1 x	Aluminium cap bolt washer M3 red (8 pcs)
1 x	Circlik for shaft 2.3 mm (10 pcs)
1 x	Aluminium wide washer M4 Blue (4 pcs)
1 x	Glass fabric tape 49 g/m² (Interglas 02037, finish FE 600/800, p
1 x	Foaming agent for epoxy resins 200 g
1 x	Wing-connector: Glass / Carbon tube (26.5/25 x 25/23) x 1000 mm
1 x	Mixing tube for double syringes and cartridges (MR 1:1 and 2:1)
1 x	Cabin latch Fox MDM1 4m (pair)
1 x	Locking cable tie 2.5x100 (uds)
1 x	Carbon fibre tape 125 g/m², 3k, UD (50 mm) roll/ 100 m
1 x	Cyanoacrylate MD GLUE plus 405, for extreme loads 20g
1 x	Release wax 250ml
1 x	Glass fabric tape 225 g/m² (Silane, plain) 40 mm X 100m
1 x	AIREX® Sheets C 70.55 (YELLOW) 1200x550x1.2 mm (5 pcs)
1 x	Vacuum sealing tape, 2.5 x 12 mm (up to 140 °C) 15 m
1 x	Glass fabric tape 225 g/m² (Silane, plain) 40 mm

567.40EUR