258.00EUR

DUPLEX 2.4EX Central Box 210
[JETCB210]

JETI Duplex 2.4EX Central Box 210
Product description and features
The Central Box 210 is the successor to the popular Central Box 200. Especially for the use of powerful and power-hungry servos, the Central Box 210 uses an aluminum housing and avoids the over current protection of the servo slots. The Central Box 210 offers true battery redundancy, DITEX servo telemetry, JETI EX telemetry and up to three receiver inputs (2x 2.4GHz and 1x 900MHz) for full power and RF signal redundancy.
Configuration via JETI Duplex DS/DC transmitters
With JETI Duplex DC/DS transmitters, the full potential of the Central Box 210 can be fully exploited. The device overview of the JETI Duplex DS/DC transmitter makes it easy to perform the entire configuration of the servo outputs, DITEX servo and JETI EX telemetry, function assignment, and more.
Compatibility with Futaba
The Central Box 210 can also be used with two S.Bus receivers (e .g Futaba R7003SB). Setting up and reading out the telemetry values must, however, be realized with a separatly available JETIBOX.
Switching on and off The switching on and off process of the Central Box 210 is done with the supplied magnetic switch.
Recommended receivers
As receiver e. g. 2 RSat2 or REX3 receivers can be used. Optionally, the use of a REX Assist receiver in combination with a RSat2 receiver is possible, so you get a Central Box with gyro stabilization.
Features
Configurable servo outputs
Battery connections 2x MPX connector system
Robust aluminum housing for extra cooling and protection
Firmware upgradeable via JETI USB adapter and JETI Studio
Wireless programming via the device overview of the DC/DS transmitters
Up to 3 independent receiver inputs (R1, R2, E1/R3)
Up to 15 servo slots (suitable for DITEX servo telemetry)
Up to 3 telemetry sensor inputs (E1/R3, E2/15, E3/14)
Input for supplied magnetic switch or optional RC switch
Optional over current protection
The Central Box 210 is not equipped with the built-in overload protection of the servo slots. To protect critical servos such tow coupling servos, retractable landing gears or spoiler servos, the optional overload protection DPSI OCP (Accessories tab) can be used.
Feature
Servo outputs 15
Protected servo outputs (for servos with up to 30kg/cm)
Protected servo outputs (for servos with up to 30kg/cm)
Receiver inputs up to 3
Satellite receiver support Yes
Telemetry Yes
DITEX servo telemetry Yes
Battery inputs 2
Supply voltage [V] 4 up to 8.4
Voltage regulator No
Permanent current [A] 20
Peak current (approx. 2 seconds) [A] 90
Idle current [µA] 180
Operating temperature [°C] ([°F]) -20 to 75 (-4 to 167)
Dimensions [mm] ([in]) 66 x 42 x 18 (2.6 x 1.65 x 0.71)
Weight [g] ([oz]) 59 (2.08)

under request

Reviews

Quick Find

Shopping Cart

1 x	Threaded coupler ALU M2,5 Ø 3 (2 uds)
1 x	Clevis plastico I=45 mm / hole 3mm / pin 1 (2 pcs)
1 x	Kwik link AL M2,5 L:23 mm (2 pcs) + Pin Ø 1,6 mm
1 x	Threaded coupler ALU M2 Ø 4 (2 uds)
1 x	Kwik link AL M3 L:23 mm (2 pcs) + Pin Ø 1,6 mm
1 x	Ball link V1 Ø7 M4/3 (6 uds)
1 x	Clevis plastico I=30 mm / hole 2.5mm / pin 1 (2 pcs)
1 x	Clevis plastico I=26 mm / hole 2mm / pin 1 (2 pcs)
1 x	Z type of cable coupler Ø 2 (2 uds)
1 x	Ball Link M2 with Ball and Hardware, 10 pcs
1 x	Threaded coupler ALU M3 Ø 6 (2 uds)
1 x	Aluminium coupler M2,5/2 with ball bearing (1 pcs)
1 x	Threaded coupler M2 (10 uds)
1 x	Gold antispark 4 mm plug
2 x	2 mm male connector (2 pcs) with safety connector
2 x	XH female balance (4S) connector (2 pcs)
1 x	XH male balance (5S) connector (2 pcs)
2 x	Conector BEC female (10 pcs)
1 x	Banna gold connector 2,5 mm (M/F)
2 x	XH female balance (3S) connector (2 pcs)
2 x	Conector BEC male (10 pcs)
2 x	EC5-Set male, simple quality, 2 x female pin, 1 x blue housing
1 x	MPX Sub-D Adaptor
1 x	Optotronix Aurora Plug
1 x	XH male balance (3S) connector (2 pcs)
1 x	Stickers-digit for marking
2 x	B4-0 rocket charges (6 pcs)
1 x	ABS "T" angle 4.0x4.0x1000 mm
1 x	ABS angle 10,0x10,0x1000 mm
1 x	Streamline Stainless Steel Tubing 7.5x4.5x1000 mm
1 x	Red smoke canister 140 g
1 x	AX-60 starters (5 pcs)
2 x	"S" set for planes
1 x	Smoke set "S"
2 x	Profile ABS half cane 2.0x1000 mm
1 x	Blue smoke canister 100 g
1 x	"M" set
1 x	ABS "T" angle 6.0x6.0x1000 mm
1 x	Smoke set "M"
1 x	Streamline Stainless Steel Tubing 9.0x5.0x1000 mm
1 x	U Profile ABS 5,0x10,0x1000 mm
1 x	White smoke bombs AX-9 (10 pcs)
2 x	Red smoke canister 65 g
2 x	L-Connector 1.5 mm x 1000 mm
2 x	Profile ABS half cane 2.5x1000 mm
1 x	U Profile ABS 2,0x4,0x1000 mm
1 x	Streamline Stainless Steel Tubing 10.5x5.7x1000 m
2 x	Streamline Stainless Steel Tubing 19.5x9.8x1000 mm
1 x	PCARD Wireless System
1 x	White smoke bombs AX-18 (5 pcs)
1 x	White smoke canister 65 g
1 x	White smoke canister 140 g
1 x	Streamline Stainless Steel Tubing 12.3x7.7x1000 mm
2 x	T-Connector 4.0 mm x 1000 mm
1 x	U Profile ABS 3,0x6,0x1000 mm
1 x	Red smoke bombs AX-60 (5 pcs)
1 x	Smoke set "Glider"
1 x	Initior Transmitter FTX2 Wireless
2 x	Parachutist
1 x	CM-3
1 x	Ball link M1.6 (6 uds)
1 x	Long ball link M3 (6 uds)
1 x	Xplorer3 anemometro
1 x	Futaba Female 40 cm extension
1 x	Extension silicon 10 cm (Graupner)
1 x	Spray adhesive INFUTAC (Clear) 500 ml
1 x	Monokote PLATINO metalizado (1.8x0.65m)
1 x	Aluminium wide washer M4 Blue (4 pcs)
2 x	Mixers smoke bombs AX-60 (5 pcs)
2 x	Streamline Stainless Steel Tubing 6.3x3.5x1000 mm
1 x	Profile ABS Square 2 x 1000 mm
1 x	Streamline Stainless Steel Tubing 17.8x12.4x1000 mm
1 x	Profile ABS triangular 6.0x1000 mm 90º
1 x	Yellow smoke canister 65 g
1 x	Remote electric ignition system
1 x	Profile ABS Square 1 x 1000 mm
1 x	Angle support XT60 conector
1 x	Aro pasacable Ø20 mm (4 pcs)
1 x	Recessed MPX connector support (6 pcs)
1 x	Support Antena 2.4 Ghz (2 pcs)
1 x	Tapa estado carga XT-60 (6 pcs)
1 x	Conector MT-60 (pair)
1 x	Battery Protection Circuit Board 22.2v 6s
1 x	Aluminun wheel collar 5 mm Ø (4 uds)
1 x	Battery bed V2_M (black)
1 x	Conector AS150 7mm antichispazo (Set: 2 pares)
2 x	Conector XT-30 (macho)
2 x	Connectors banana oro 6,0 mm Ultralight (M/F)
1 x	Conector FUTABA Servo female (10 pcs)
1 x	XH female balance (9S) connector (2 pcs)
1 x	Connector CAN 15
2 x	Conector JR Servo male (10 pcs)
1 x	Banna gold connector 2,5 mm (100 M/F pairs)
1 x	Connectors banna oro 2 mm (M/F)
1 x	Connectors DEANS (T)
2 x	Conector MR-60 (pareja)
1 x	Field folding model stand
1 x	Propeller balancer
1 x	Angle measurer
1 x	Field folding model stand SebArt
1 x	STEERING FRONT WHEEL SYSTEM BIDULE 111
1 x	Steering arm 12 mm Ø 3 mm (2 uds)
1 x	STEERING FRONT WHEEL SYSTEM BIDULE 55
1 x	Split pin 1x8 mm (10 uds)
1 x	Stainless steel cable Ø 0.62 mm (10 m)
1 x	Steering arm 12 mm Ø 4 mm
1 x	Wheel collar 2 mm Ø (4 uds)
1 x	Wing connector 8pin with pin strip, plug & socket
1 x	Connectors MPX black female
1 x	Connectors DEANS (T) micro
1 x	Connectors banna oro 0,8 mm (M/F)
1 x	Bag connector 2 mm
1 x	Connectors banna oro 6,0 mm (M/F)
1 x	XH male balance (8S) connector (2 pcs)
1 x	LiPo Storage Box Type "P"
1 x	Aluminun wheel collar 3.5 mm Ø (4 uds)
1 x	Conector JR/Uni Servo male BLUE silicon (10 pcs)
1 x	EC5-Set female, simple quality, 2 x female pin, 1 x blue housing
1 x	Connectors banna oro 4 mm (M/F)
1 x	XH female balance (8S) connector (2 pcs)
1 x	Wheel collar 4 mm Ø (4 uds)
1 x	Tester LiPo/LiIon/LiMn/LiFe
1 x	Mudguard for 140/165 mm wheels
1 x	Aluminun wheel collar 2.5 mm Ø (4 uds)
1 x
1 x	ABS angle 3,0x3,0x1000 mm
1 x	U Profile ABS 8,0x4,0x1000 mm
1 x	Profile ABS half cane 4x1000 mm
2 x	Streamline Stainless Steel Tubing 15.5x8.5x1000 mm
1 x	Ventral support for AX-18/AX-60
1 x	ABS "T" angle 8.0x8.0x1000 mm
1 x	Wing tips support for AX-18/AX-60 (2 pcs)
1 x	Fresa corte diamante Ø 1.0mm (bola)
1 x	Green smoke canister 65 g
2 x	U Profile ABS 1,0x2,0x1000 mm
1 x	L-Connector 1.0 mm x 1000 mm
1 x	ABS rectangular profile 10x5.0x1000 mm
1 x	Red smoke canister 100 g
1 x	Profile ABS half cane 8.0x1000 mm
1 x	Yellow smoke bombs AX-60 (5 pcs)
1 x	White smoke bombs AX-60 (5 pcs)
1 x	Ball Link Plier
1 x	Green smoke canister 100 g
1 x	Medidor ángulos y/o incidencias
1 x	Angle of incidence meter
1 x	SkyMaxx 1.550 mm (kit)
1 x	Jodel D.9 BeBe 2.400 mm Kit
1 x	Antonov AN2 Scale 1/6 - 3m
1 x	Servo TOPMODEL DS1413 T
1 x	Servo HITEC HS-125 MG
1 x	Servo HITEC D145 SW
1 x	Servo lock HS-80/81/82/85 (2 pcs)
1 x	Servo HITEC D950 TW
1 x	Servo HS-5565MH High Voltage
1 x	Servo Digital HITEC HS-5065 MG
1 x	Extension for LC-Display 50cm
1 x	BlueCom™ Adapter (iOS)
1 x	13 mm wing servo holder
1 x	57 mm micro-mini servo cover
1 x	11 mm wing servo holder
1 x	PS-050 TONEGAWA Servo
1 x	ASH 31 Mi Scale:1/3 - 7m, elevator
1 x	Conector XT-30 (hembra)
1 x	Canopy Lock V1 M3 Red (2 pcs)
1 x	Cable grommet Ø 4 mm (4 uds)
1 x	250 mm / 16 mm Airbrakes
1 x	Cabin latch Fox MDM1 4m (pair)
1 x	MR30 connector male
1 x	XH male balance (2S) connector (2 pcs)
1 x	Aluminun wheel collar 4 mm Ø (4 uds)
1 x	DUPLEX 2.4EX Central Box 320 + 2x Rsat2 + RC Switch
1 x	XT-60 connector (female)

7,027.27EUR