258.00EUR

DUPLEX 2.4EX Central Box 210
[JETCB210]

JETI Duplex 2.4EX Central Box 210
Product description and features
The Central Box 210 is the successor to the popular Central Box 200. Especially for the use of powerful and power-hungry servos, the Central Box 210 uses an aluminum housing and avoids the over current protection of the servo slots. The Central Box 210 offers true battery redundancy, DITEX servo telemetry, JETI EX telemetry and up to three receiver inputs (2x 2.4GHz and 1x 900MHz) for full power and RF signal redundancy.
Configuration via JETI Duplex DS/DC transmitters
With JETI Duplex DC/DS transmitters, the full potential of the Central Box 210 can be fully exploited. The device overview of the JETI Duplex DS/DC transmitter makes it easy to perform the entire configuration of the servo outputs, DITEX servo and JETI EX telemetry, function assignment, and more.
Compatibility with Futaba
The Central Box 210 can also be used with two S.Bus receivers (e .g Futaba R7003SB). Setting up and reading out the telemetry values must, however, be realized with a separatly available JETIBOX.
Switching on and off The switching on and off process of the Central Box 210 is done with the supplied magnetic switch.
Recommended receivers
As receiver e. g. 2 RSat2 or REX3 receivers can be used. Optionally, the use of a REX Assist receiver in combination with a RSat2 receiver is possible, so you get a Central Box with gyro stabilization.
Features
Configurable servo outputs
Battery connections 2x MPX connector system
Robust aluminum housing for extra cooling and protection
Firmware upgradeable via JETI USB adapter and JETI Studio
Wireless programming via the device overview of the DC/DS transmitters
Up to 3 independent receiver inputs (R1, R2, E1/R3)
Up to 15 servo slots (suitable for DITEX servo telemetry)
Up to 3 telemetry sensor inputs (E1/R3, E2/15, E3/14)
Input for supplied magnetic switch or optional RC switch
Optional over current protection
The Central Box 210 is not equipped with the built-in overload protection of the servo slots. To protect critical servos such tow coupling servos, retractable landing gears or spoiler servos, the optional overload protection DPSI OCP (Accessories tab) can be used.
Feature
Servo outputs 15
Protected servo outputs (for servos with up to 30kg/cm)
Protected servo outputs (for servos with up to 30kg/cm)
Receiver inputs up to 3
Satellite receiver support Yes
Telemetry Yes
DITEX servo telemetry Yes
Battery inputs 2
Supply voltage [V] 4 up to 8.4
Voltage regulator No
Permanent current [A] 20
Peak current (approx. 2 seconds) [A] 90
Idle current [µA] 180
Operating temperature [°C] ([°F]) -20 to 75 (-4 to 167)
Dimensions [mm] ([in]) 66 x 42 x 18 (2.6 x 1.65 x 0.71)
Weight [g] ([oz]) 59 (2.08)

Bajo pedido

Comentarios

Búsqueda Rápida

Cesta de Compras

1 x	Rueda 127x43 centro aluminio Ø6.0 mm
1 x	Sistema cierre HACKER 300 mm con abrazadera (2 pcs)
1 x	Soporte para bridas hasta 3 mm (0,12") para tornillo M3 (10 pcs)
1 x	Cinta autoadhesiva 5 mm x 16.80m; Diente 0.5 mm
1 x	Cinta fibra vidrio 50 mm
1 x	Sistema cierre 320 mm largo (5 pcs)
1 x	Cinta autoadhesiva 20 mm x 12m; Diente 1.0 mm
1 x	Sistema cierre 350 mm con abrazadera (2 pcs)
1 x	Sistema cierre Mini 14x60 mm (4 pcs)
1 x	Sistema cierre 250 mm con abrazadera (2 pcs)
2 x	Cinta fibra vidrio 38 mm
1 x	Sistema cierre 400 mm con abrazadera (2 pcs)
1 x	Cinta Goldfix 1m
1 x	Sistema cierre 450 mm con abrazadera (2 pcs)
1 x	Cinta tubuladora (5 m)
1 x	Sistema cierre 330 mm con abrazadera (4 pcs)
1 x	Cinta alerones 1m x 10mm
1 x	Sistema cierre 200 mm con abrazadera (2 pcs)
1 x	Cinta RUDDOG proteccion calor 2m x 50 mm
1 x	Cinta SURFACE 21mm x 5m
1 x	Cinta autoadhesiva 10 mm x 12m; Diente 0.5 mm
1 x	Sistema cierre 300 mm con abrazadera (2 pcs)
1 x	Sistema cierre 240 mm con abrazadera (2 pcs)
1 x	Tubo ABS 8,0x6,0x1000 mm
1 x	Tubo ABS 14,0x10,0x1000 mm
1 x	Tubo ABS 9,0x7,0x1000 mm
1 x	Tubo ABS 20,0x18,0x1000 mm
1 x	Tubo ABS 18,0x16,0x1000 mm
1 x	Tubo ABS 12,0x10,0x1000 mm
1 x	Tubo acero (L 1000 mm, Ø10 mm, Ø9,7 mm)
1 x	Tubo ABS 3,0x1,0x1000 mm
1 x	Tubo aluminio (L 1000 mm, Ø4,0 mm, Ø3,1 mm)
1 x	Tubo acero (L 1000 mm, Ø12 mm, Ø11,7 mm)
1 x	Tubo ABS 4,0x2,0x1000 mm
1 x	Tubo acero (L 1000 mm, Ø5 mm, Ø4,7 mm)
1 x	Tubo ABS 6,0x5,0x1000 mm
1 x	Tubo ABS 5,0x3,0x1000 mm
1 x	Tubo ABS 3,0x2,0x1000 mm
1 x	CC 02
1 x	Adaptador 2 LiPos XH>EH
1 x	CM-3
1 x	CC 05
2 x	Cable "Y" equilibrador 5S, 2x JST-XH / 1x JST-EH
2 x	APM2,6 Power module con BEC 5,3 V DC
1 x	Cable "Y" equilibrador 7S, 2x JST-XH / 1x JST-EH
2 x	Adaptador TP/TopFuel - XH 2/3S
1 x	Cable USB para programación HLS
1 x	BEC 3A FOXY
2 x	Cable carga bateria transmisor Futaba 2x0,5 qmm (50 cm)
3 x	Adaptador 3 LiPos XH>EH
2 x	Alambre de cobre esmaltado en rojo Ø0,2 mm (5 m)
1 x	Gancho de remolque hasta 4,5 m
1 x	Extractor piñones 2.3/3.2 mm
2 x	Bisagra cilíndrica 33 mm Ø 2 mm (5 pcs)
2 x	Anemometro Xplorer4
2 x	Ball link Aluminio M4 x 4 x 6 x 26mm (4 uds)
2 x	Barra pegamento caliente Verde
1 x	Aceite DELUXE turbine Jet Oil 1 litro
1 x	Bisagra cilíndrica 67 mm Ø 4,5 mm (5 pcs)
1 x	Barra pegamento caliente Rojo
1 x	Barra pegamento caliente Negro
1 x	Arrancador 12v (Max 180 and 30ccm)
1 x	Autoarranque DLE 85/111/120 (motor incluido)
2 x	Bascula precision 0.1-2000 g
2 x	Batería Sanyo Eneloop AAA 1,2 V 800 mAh
1 x	Bateria LRP 2200-7.2v 6 cell NiMH
2 x	Base para servo
1 x	Bisagra Micro flexible (12 uds)
1 x	Cable servos silicona 0,35 mm2 Graupner (100 m)
1 x	Modulo PPM Encoder
1 x	Liston de BALSA 10 x 10 x 1000 mm
1 x	Conector equilibrado XH (3S) hembra (2 pcs)
1 x	Prolongador 15 cm (Futaba)
1 x	Horn aluminio anodiazado 6 mm azul con rótula
1 x	Prolongador S-Bus 1-2 silicona 30 cm
1 x	Rueda de cola 18 mm
1 x	Motor ACTRO 28-4-880
1 x	Regulador NAVY V15R
1 x	Barco pesquero Jule Fischkutter
1 x	Tubo de latón (L 1000 mm, Ø7,0 mm, Ø6,1 mm)
1 x	Tubo de latón (L 1000 mm, Ø8,0 mm, Ø6,1 mm
3 x	Alambre de cobre esmaltado en negro Ø0,2 mm (5 m)
2 x	Cable BEC 30 cm (hembra)
1 x	Cable carga bateria transmisor Graupner 2x0,5 qmm (50 cm)
1 x	Anemometro Xplorer3
1 x	Cable BEC 30 cm (macho)
1 x	Prolongador 2/3 lipos conector JST - JST/C
1 x	Conector doble con soporte JR con prolongación 200 mm
1 x	Gancho de lanzamiento fijo
1 x	PSC 6
1 x	Cable carga emisora GRAUPNER
1 x	Conector Sub-D 2+5 Hembra
1 x	CC 03
1 x	Circlick seguridad
2 x	Adaptador 4 LiPos XH>EH
1 x	DPS Interruptor JR/JR
1 x	Conector Sub-D 2+5 Macho
1 x	Conector AWG Macho 6 pines
1 x	Alambre cobre esmaltado 3 hilos trenzados rojo/negro/cobre Ø0,2
1 x	Cable de entrenamiento para GWS T4A II (maestro-alumno)
1 x	Anemometro Xplorer1
1 x	Cono 51 mm aluminio
1 x	Arrancador 12v (Max 90 and 15ccm)
1 x	Cono 102 mm Cromo
1 x	Bisagra cilíndrica 43 mm Ø 2,5 mm (5 pcs)
1 x	Tubo carton cohete 50mm x 48mm x 250mm
1 x	Cono 38 mm aluminio
1 x	Cono 90 mm largo Fibra CFK con tornillo central
1 x	Cono 90 mm Fibra GFK
1 x	Anclaje cabina en L "tipo F3A" (2 pcs)
1 x	Conector de seguridad para servos (2 pcs)
1 x	Cinta adhesiva impermeable, ancho 19 mm, largo 25 m
1 x	Bayoneta aluminio/strongal D35 mm/1 m
1 x	Receptor CORE PBR-26XS 26ch
1 x	PowerBox Mobile Terminal
1 x	Kwik link aluminio IZD. M3 L: 30mm (6 uds) pin Ø 2 mm
1 x	Pin Ø 2 mm para Kwik link MPJ2162/2163 (6 pcs)
1 x	Kwik link metálico M2,5 (10 uds)
1 x	Kwik link aluminio IZD. M3 L: 30mm (2 uds) pin Ø 2 mm
1 x	Kwik link y brazo de nylon M4xM2,5xL30
1 x	Polea de bronce 10/2 (2 pcs)
1 x	Kwik link metálico M3 (10 uds)
1 x	Kwik link micro (10 uds)
1 x	Pin Ø 1,6 mm para Kwik link MPJ2160/2161 (6 pcs)
1 x	Kwik link aluminio M3 L:30mm (6 uds) pinØ 1.6mm Izda
1 x	Kwik link negro largo (10 pcs)
1 x	Bancada aluminio servo (2 uds)
1 x	AC-10 pre-rotacion + motor
1 x	Cono 105 mm Fibra GFK
1 x	Anemometro Xplorer2
1 x	Acumulador polvo para limpieza moldes
1 x	Conexión de vacío VA 1 (para manguera Ø 6 mm)
1 x	Tubo carton cohete 25mm x 24mm x 230mm
1 x	Cono 105 mm Carbono CFK
1 x	Cono 110 mm Fibra GFK
1 x	Cono 100 mm Carbono CFK
1 x	Cabestrante de plástico de 91x44x45 mm
1 x	Tubo carbono 3K-PW (Ø18 mm, Ø16 mm L:1000 mm)
1 x	Tubo carbono (L 1000 mm, Ø4 mm, Ø2,5 mm)
2 x	Tubo carbono (L 1000 mm, Ø4 mm, Ø3 mm)
1 x	Tubo carbono (L 1000 mm, Ø12 mm, Ø10 mm)
1 x	Tubo carbono (L 1000 mm, Ø2 mm, Ø1 mm)
1 x	Tubo carbono (L 1000 mm, Ø3 mm, Ø2 mm)
1 x	Tubo carbono 3K-PW (Ø12 mm, Ø10 mm L:1000 mm)
1 x	Tubo carbono (L 1000 mm, Ø6 mm, Ø4 mm)
1 x	Tubo carbono 3K-PW (Ø22 mm, Ø20 mm L:1000 mm)
1 x	Helice pleg. VITAPROP 15x9.5 carbono
1 x	Tubo carbono 3K (Ø 8 mm, Ø 7 mm L:1000 mm)
1 x	Tubo carbono (L 2000 mm, Ø12 mm, Ø10 mm)
1 x	Tubo carbono (L 1000 mm, Ø5 mm, Ø3 mm)
1 x	Tubo carbono (L1000 mm, Ø1 mm, Ø0,5 mm)
1 x	Tubo carbono 3k-LW (L 2000 mm, Ø30 mm, Ø28 mm)
1 x	Tubo carbono (L 1000 mm, Ø30 mm, Ø26 mm)
1 x	Cable silicona "Y" 30 cm (Graupner)
1 x	Motor OS 3820-1200 eléctrico
1 x	Cable silicona 0,25 mm² blanco (25 m)
1 x	Cable servos PVC 0,35 mm2 Graupner (100 m)
1 x	Interruptor magnético MPS para encendido
1 x	Bateria RX JETI LiIon RB 5200 7.2v
1 x	Conector alas/fuselaje para 16 pines AWG 20-24
1 x	Cable Futaba voltaje externo para telemetria

3,751.75EUR