258.00EUR

DUPLEX 2.4EX Central Box 210
[JETCB210]

JETI Duplex 2.4EX Central Box 210
Product description and features
The Central Box 210 is the successor to the popular Central Box 200. Especially for the use of powerful and power-hungry servos, the Central Box 210 uses an aluminum housing and avoids the over current protection of the servo slots. The Central Box 210 offers true battery redundancy, DITEX servo telemetry, JETI EX telemetry and up to three receiver inputs (2x 2.4GHz and 1x 900MHz) for full power and RF signal redundancy.
Configuration via JETI Duplex DS/DC transmitters
With JETI Duplex DC/DS transmitters, the full potential of the Central Box 210 can be fully exploited. The device overview of the JETI Duplex DS/DC transmitter makes it easy to perform the entire configuration of the servo outputs, DITEX servo and JETI EX telemetry, function assignment, and more.
Compatibility with Futaba
The Central Box 210 can also be used with two S.Bus receivers (e .g Futaba R7003SB). Setting up and reading out the telemetry values must, however, be realized with a separatly available JETIBOX.
Switching on and off The switching on and off process of the Central Box 210 is done with the supplied magnetic switch.
Recommended receivers
As receiver e. g. 2 RSat2 or REX3 receivers can be used. Optionally, the use of a REX Assist receiver in combination with a RSat2 receiver is possible, so you get a Central Box with gyro stabilization.
Features
Configurable servo outputs
Battery connections 2x MPX connector system
Robust aluminum housing for extra cooling and protection
Firmware upgradeable via JETI USB adapter and JETI Studio
Wireless programming via the device overview of the DC/DS transmitters
Up to 3 independent receiver inputs (R1, R2, E1/R3)
Up to 15 servo slots (suitable for DITEX servo telemetry)
Up to 3 telemetry sensor inputs (E1/R3, E2/15, E3/14)
Input for supplied magnetic switch or optional RC switch
Optional over current protection
The Central Box 210 is not equipped with the built-in overload protection of the servo slots. To protect critical servos such tow coupling servos, retractable landing gears or spoiler servos, the optional overload protection DPSI OCP (Accessories tab) can be used.
Feature
Servo outputs 15
Protected servo outputs (for servos with up to 30kg/cm)
Protected servo outputs (for servos with up to 30kg/cm)
Receiver inputs up to 3
Satellite receiver support Yes
Telemetry Yes
DITEX servo telemetry Yes
Battery inputs 2
Supply voltage [V] 4 up to 8.4
Voltage regulator No
Permanent current [A] 20
Peak current (approx. 2 seconds) [A] 90
Idle current [µA] 180
Operating temperature [°C] ([°F]) -20 to 75 (-4 to 167)
Dimensions [mm] ([in]) 66 x 42 x 18 (2.6 x 1.65 x 0.71)
Weight [g] ([oz]) 59 (2.08)

under request

Reviews

Quick Find

Shopping Cart

1 x	Cap Hispano Aviación
1 x	Vest clothes Hispano Aviación
1 x	Carbon fiber rod 1.0 mm x 1000 mm
1 x	Carbon fiber rod 0.5 mmx1000 mm
2 x	Carbon fiber rod 3.0 mm x 1000 mm
1 x	Carbon fiber rod 20 mmx1000 mm
2 x	Carbon fiber rod 2.5 mmx1000 mm
1 x	Carbon fiber rod 6.0 mmx1000 mm
1 x	Carbon fiber rod 5.0 mmx1000 mm
1 x	Carbon fiber rod 1.5 mm x 2000 mm
1 x	Carbon rectangular rod 3.0 mm x 1.0 x 1000 mm
2 x	Carbon rectangular rod 10.0 mm x 1.0 x 1000 mm
1 x	Carbon fiber flat 1000x3.0x1.0 mm
1 x	Carbon fiber flat 1000x3.0x1.0 mm
1 x	Carbon fiber rod 10 mm x 1000 mm
1 x	Squared carbon wing joinner 5x5x220 mm
1 x	Carbon fiber rod 1.5 mm x 1000 mm
2 x	Carbon fiber rod 12 mm x 1000 mm
1 x	Carbon fiber rod 8.0 mmx1000 mm
1 x	Carbon fiber rod 16 mm x 1000 mm
1 x	Camera Sony 4140+673 CCD with Built-in 200mw TX + antenna
1 x	USB Mini Camera endoscope
1 x	Brake for 140 mm wheels
1 x	Kit hydraulic brake
1 x	Foil for sticking flaps and ailerons
2 x	SE Ring 250 mm (2 pcs)
2 x
1 x	SE Ring 480 mm (2 pcs)
1 x	14x60 mm Mini rings Tie Wraps (4 pcs)
1 x	26 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
2 x	13 mm self adhesive Pinking Tape, saw tooth height 1.0 mm
2 x	5 mm self adhesive Pinking Tape, saw tooth height 0.5 mm
1 x	White smoke bombs AX-60 (5 pcs)
1 x	43 x 10 mm cylidric hinge Ø 2,5 mm (10 pcs)
1 x	Conector BEC female (10 pcs)
1 x	Tap FESTO 4-4 mm
1 x	Crimping sleeves for 1.1 mm cable (10 pcs)
1 x	Silicone 0,50 qmm servos wire Graupner(100 m)
2 x	Duplex 2.4EX tray transmitter DC-16 II Black multimode
2 x	Carbon wing joinner 13,4 mm Ø 0,48 mm
1 x	Transmitter Balancer HITEC Aurora 9, JR and Spectrum (blue)
2 x	Carbon fiber rod 4.0 mmx1000 mm
1 x	TX-Tray V1 (L) (Black)
1 x	DUPLEX 2.4EX Central Box 220
1 x	Suncover 100cc Red
2 x	DUPLEX 2.4 EX MVario2
1 x	Sun Cover ULTIMATUM 2.0 (Hispano Aviacion)
2 x	PPM to Jack link - Tx Black (mono) DC/DS Tx DUPLEX 2,4EX
1 x	COPILOT Multiplex
1 x	40 mm servo arm with bearing (2 pcs)
1 x	Servo GO-1053 MG 20.0kg
1 x	Black tray 2,4EX DC-16/14/24 black
1 x	Servo holder for retract
1 x	Futaba 14/20 mm servo pull-pull double arm with ball link
2 x	DUPLEX 2,4EX Stick with 2-Position Switch for Transmitter DC/DS
1 x	Neck strap JETI DS
1 x	Servo arm with 6 mm hole to FEMA 9800A
2 x	Caps multicolor Switch JETI
1 x	Futaba 52 mm servo arm
1 x	SERVO DES 707 BB MG, Pignons
1 x	DS-12/14/16 - Black nuts for upper switches - Front panel (2pcs)
1 x	Switch for DS: Long 3 Position
1 x	Blade Holder Full (4 blades)
1 x	Servo GO-1013 MG 3.8kg
1 x	Hitec 52 mm servo arm
1 x	Savox Highvoltage Brushless Servo SB-2272MG (Tail rotor)
1 x	SERVO DES 658 BB MG
1 x	Stick with Button DC/DS-16/14/24 Tx DUPLEX 2,4EX
1 x	DUPLEX 2,4EX Stick with Potentiometer for Transmitter DC/DS
1 x	Futaba 24/30 mm servo pull-pull double arm with ball link
1 x	Servo AN-20 MGBBA
1 x	Switch Button DS Tx DUPLEX
1 x	Carbon fiber rod 7.0 mmx1000 mm
1 x	Futaba 25 mm servo arm with ball link
1 x	Hitec 38 mm servo arm with ball link
1 x	JETI Counter for DC-16 (Blue)
1 x	switch 1-Spring-DOWN 3-position DS Tx DUPLEX 2,4EX
1 x	Hitec 46 mm servo arm with ball link
1 x	Servo GO-1035MG 16 kg.cm 0.08s/60º
1 x	Futaba 2x20 mm servo double arm
1 x	LA500 pre-rotation gear
1 x	Servo TOPMODEL S7520 MG
1 x	Head core bushing
1 x	Servo KST BLS815 HV V2.0 Servo 20mm 70g 20Kg
1 x	Shirt Hispano Aviación
1 x	Nut M1,6
1 x	Blade holder upper
1 x	LA500 housing-lower cyclic
1 x	Soporte servo KST X10 mini / DS135MG
1 x	LA500 Blades
1 x	LA500 housing-upper cyclic
1 x	Servo KST X20 8.4-50 V8.0 45kg 8.4v Softstar
1 x	Servo KST A15-1810 20kg/cm@8.4V / Coreless Motor
1 x	Head core
1 x	Carbon fiber rod 0.5 mmx1000 mm
1 x	Carbon fiber flat 1000x6.0x0.8 mm
1 x	Yellow smoke canister 140 g
1 x	SE Ring 330 mm (4 pcs)
1 x	SE Ring 200 mm (2 pcs)
1 x	Big-Malibu XL Roof box with surfboard rack GREY
1 x	Straightened rod Ø 1.5 mm x 1500 mm
1 x	Aluminium rod Ø 4.0 mm x 3000 mm
1 x	Tren de cola carbono 50-70cc
1 x	Tail wheel for 8-12 kg models
1 x	28 mm tailwheel unit
1 x	20x1000 mm Ring Strap Back To Back
1 x	SE Ring 350 mm (2 pcs)
1 x	RUDDOG Protection and Heat Shield Tape (2mx50mm)
1 x	20x200 mm battery rings
1 x	SE Ring HACKER 300 mm (2 pcs)
1 x	Cable-Tie 1.66x71mm / 0.07x2.8″ (20 pcs)
1 x	SE Ring 240 mm (2 pcs)
1 x	Tape GFK 50 mm
1 x	SE Ring 400 mm (2 pcs)
1 x	DUPLEX 2.4EX Central Box 320 + 2x Rsat2 + RC Switch
1 x	DUPLEX 2.4EX MU 3 Sensor
1 x	DSM 10 Dual Switch Mixer
1 x	DUPLEX 2.4EX Central Box 220 + 2x Rsat2
1 x	Battery RX JETI LiIon RB 2600 7.2v
1 x	DUPLEX 2.4EX MSpeed PITOT <300 Km/h
1 x	Telemetry adapter JestMunt
1 x	DUPLEX 2.4EX MT 300 EX
1 x	DUPLEX 2.4EX Central Box 210
1 x	DUPLEX 2.4EX MUI 75
1 x	DUPLEX 2.4EX MAlti (Rev.2)
1 x	Transmitter SPEKTRUM DX-9 (Only TX)
1 x	Duplex 2.4 EX TopFuel MTAG Battery Reader
1 x	DUPLEX 2.4EX Expander E2
1 x	DUPLEX 2.4 EX MBar
1 x	DUPLEX 2.4EX RC Power Switch 10
1 x	DUPLEX 2.4EX Expander E4
1 x	Car Charger DC/DS-16
1 x	DUPLEX 2,4EX Stick with 3-Position Switch for Transmitter DC/DS
1 x	DUPLEX 2.4EX Central Box 320
1 x	AddCAP 10AS capacitors
1 x	Battery RX JETI LiIon RB 3100 7.2v

10,654.75EUR