534.01EUR

DUPLEX 2.4EX Central Box 320 + 2x Rsat2 + RC Switch
[JETCB3202+]

JETI DUPLEX 2.4EX Central Box 320 + 2x Rsat2 + RC Switch

Product description and features
The Central Box 320 is designed for a complete management of multiple servos and two receiver batteries for a model with high security requirements.The Central Box 320 has an overload protection on each servo output, 8 channels for high-performance servos up to 60 kg / cm and 10 channels for standard servos up to 30 kg / cm. Especially for the use of powerful and power-hungry servos, the Central Box 320 has an aluminum housing for better cooling. The Central Box 320 offers true battery redundancy, DITEX servo telemetry, JETI EX telemetry and up to three receiver inputs (2x 2.4GHz and 1x 900MHz) for full power and RF signal redundancy.

Configuration via JETI Duplex DS/DC transmitters
With JETI Duplex DC/DS transmitters, the full potential of the Central Box 320 can be fully exploited. The device overview of the JETI Duplex DS/DC transmitter makes it easy to perform the entire configuration of the servo outputs, DITEX servo and JETI EX telemetry, function assignment, and more.

Compatibility with Futaba
The Central Box 320 can also be used with two S.Bus receivers (e .g Futaba R7003SB). Setting up and reading out the telemetry values must, however, be realized with a separatly available JETIBOX.

Switching on and off
The switching on and off process of the Central Box 320 is done with the supplied R/C switch.

Recommended receivers
Two compatible RSat2 receivers are included. Optionally, the use of a REX Assist receiver in combination with a RSat2 receiver is possible, so you get a Central Box with gyro stabilization.

Features
Adjustable powerful BEC for voltage stabilization (connection of standard or HV servos)
DITEX servo telemetry support
Possibility to connect up to 3 receivers with serial communication
built-in Expander function with the possibility of independent connection of up to four JETI EX sensors
Input for magnetic switch or RC switch
Power supply batteries connected via MPX connector
100Hz mode of servo outputs (10ms period)
EX telemetry support (measurement of voltage, current, capacity, temperature, etc.)
Easy settings changes via DC/DS transmitter („Device explorer“)
Robust metal construction with mounting holes

temporarily out of stock

Reviews

Quick Find

Shopping Cart

1 x	Xplorer2 anemometro
1 x
1 x	Dust collector for mould cleaning
1 x	BALSA leading edge 8x10x1000 mm
1 x	Jeti Black cap
1 x	Ball Bearings for motor A60-V2
1 x	Propeller diller for DA50, DLE55 red
1 x	O-ring Saito FG-73 5cyl
1 x	Propeller diller for DLE170
1 x	Propeller diller for DLE111 and DA85-150
1 x	Exhaust elbow for SAITO FA65/72/80/82a/91S/100/
1 x	Adapters for 7.5 - 35cc aircraft and naval engines
1 x	Peel ply 93 g/m² (plain weave) 150 cm x 5m
1 x	Carbon plate 350x150x4.0 mm
1 x	Resistor 3W 5% OR47
1 x	NF-3X-80 liner Kit
1 x	Cover cap drop-shaped paintable 43 mm
1 x	PET film Mylar® A 350, 50 cm, roll/ 2 m
1 x	Carbon plate 350x150x3.0 mm
1 x	Crystal TX 35.150 Ch 75
1 x	Carbon plate 1000x500x2,0 mm ECOTECH
1 x	Futaba Female 40 cm extension
1 x	ABS 500 x 400 x 1 mm (white)
1 x	Fiberglass plate 350x150x2.5 mm
1 x	Carbon plate 350x150x5.0 mm
1 x	Peel ply 95 g/m² (plain weave) 20 mm x 100 m
1 x	Fiberglass plate 350x150x3.0 mm
1 x	Jet Afterburner Simulator NF-Jet3 RY
1 x	USB Interface Adapter
1 x	NF-3m Heli Kit
1 x	NF-1 RC set
1 x	NF-3 RC set
1 x	NF-3XL set
1 x	Extension S-Bus 1-2 silicon 30 cm FUTABA
1 x	"L" servo arm 65x49 mm (2 pcs)
1 x	2 mm Prop Adapter M6
1 x	31,0 mm propeller (rigth propeller)
1 x	3 mm Prop Adapter M6
1 x	ABS "T" angle 10.0x10.0x1000 mm
1 x	ABS Strip 1.5x6.0x1000 mm
1 x	ABS I Strip 10x5x1000 mm
1 x	ABS Strip 1.0x2.0x1000 mm
1 x	4 mm Prop Adapter M6
1 x	ABS tube 18.0x16.0x1000 mm
1 x	Prop Shaft Adapter 6 mm/M8 "long" 35 mm
1 x	ABS Strip 1.5x4.0x1000 mm
1 x	2,3 mm Prop Adapter M6
1 x	ABS I Strip 20x10x1000 mm
1 x	AddCAP 10AS capacitors
1 x	DC24 II Transmitter case insert

1,860.75EUR