534.01EUR

DUPLEX 2.4EX Central Box 320 + 2x Rsat2 + RC Switch
[JETCB3202+]

JETI DUPLEX 2.4EX Central Box 320 + 2x Rsat2 + RC Switch

Product description and features
The Central Box 320 is designed for a complete management of multiple servos and two receiver batteries for a model with high security requirements.The Central Box 320 has an overload protection on each servo output, 8 channels for high-performance servos up to 60 kg / cm and 10 channels for standard servos up to 30 kg / cm. Especially for the use of powerful and power-hungry servos, the Central Box 320 has an aluminum housing for better cooling. The Central Box 320 offers true battery redundancy, DITEX servo telemetry, JETI EX telemetry and up to three receiver inputs (2x 2.4GHz and 1x 900MHz) for full power and RF signal redundancy.

Configuration via JETI Duplex DS/DC transmitters
With JETI Duplex DC/DS transmitters, the full potential of the Central Box 320 can be fully exploited. The device overview of the JETI Duplex DS/DC transmitter makes it easy to perform the entire configuration of the servo outputs, DITEX servo and JETI EX telemetry, function assignment, and more.

Compatibility with Futaba
The Central Box 320 can also be used with two S.Bus receivers (e .g Futaba R7003SB). Setting up and reading out the telemetry values must, however, be realized with a separatly available JETIBOX.

Switching on and off
The switching on and off process of the Central Box 320 is done with the supplied R/C switch.

Recommended receivers
Two compatible RSat2 receivers are included. Optionally, the use of a REX Assist receiver in combination with a RSat2 receiver is possible, so you get a Central Box with gyro stabilization.

Features
Adjustable powerful BEC for voltage stabilization (connection of standard or HV servos)
DITEX servo telemetry support
Possibility to connect up to 3 receivers with serial communication
built-in Expander function with the possibility of independent connection of up to four JETI EX sensors
Input for magnetic switch or RC switch
Power supply batteries connected via MPX connector
100Hz mode of servo outputs (10ms period)
EX telemetry support (measurement of voltage, current, capacity, temperature, etc.)
Easy settings changes via DC/DS transmitter („Device explorer“)
Robust metal construction with mounting holes

temporarily out of stock

Reviews

Quick Find

Shopping Cart

1 x	Digital Air Speed Sensor And Pitot Tube Set
1 x	PIX Hawk with accesories
1 x	PPM Encoder Module
1 x	Cabin latch Fox MDM1 4m (pair)
1 x	Oracover Yellow CADMIO 2 m
1 x	Ply-Span 450x600/13g Black
1 x	Oracover Azul 2 m
1 x	Monokote PLATINO metalizado (1.8x0.65m)
1 x	Oracover Red 2 m
1 x	Oratex Silver 2m
1 x	Steering arm 16 mm Ø 3 mm
1 x	Crimping sleeves for cable 1.3 mm (10 pcs)
1 x	Oracover Yellow CUB 2 m
1 x	Electric spoiler 250 mm (2 pcs)
1 x	Oratex Natural White 20m
1 x	Oracover ROYAL RED 2m
1 x	Canopy Latch
2 x	Screw-lock connector Ø 2 mm (2 uds)
4 x	Stainless steel cable Ø 0.5 mm (2 m)
1 x	ORACOVER transparent Yellow (10 m)
2 x	Cierre cabina aluminio Ø5, I=16 mm
1 x	Steering arm 12 mm Ø 3 mm (2 uds)
1 x	MYLAR film A350 (1000x500 mm)
1 x	Screw-lock connector M2 (2 uds)
1 x	Ply-Span 450x600/13g Red
1 x	L cockpit anchor "tipe F3A" (2 pcs)
1 x	Oracover White 2 m
1 x	Ply-Span 450x600/13g White
2 x	Stainless steel cable Ø 0.5 mm (20 m)
1 x	Oracover Azul Cielo 2 m
1 x	Cap closure 33/23.5mm (2 uds)
2 x	One touch canopy lock
2 x	Steering arm 12 mm Ø 4 mm
1 x	Oratex Red Fokker 10 m
1 x	Oracover White 10 m
1 x	Oracover CARBON Metalic 1 m
1 x	Locking cable tie 2.5x100 (uds)
1 x	Oracover Green10 m
1 x	Monokote BLANCO jet (1.8x0.65m)
1 x	Big-Malibu XL Roof box with surfboard rack GREY
1 x	Connectors DEANS 4 pins (1 pair)
2 x	Straightened rod Ø 14.0 mm x 1000 mm
2 x	XH female balance (3S) connector (2 pcs)
1 x	Connectors banna oro 8,0 mm (Male) 5 pcs.
1 x	Connectors DEANS (T)
1 x	Banna gold connector 2,5 mm (100 M/F pairs)
1 x	Optotronix Aurora Plug
1 x	Connectors banana oro 6,0 mm Ultralight (M/F)
2 x	Connectors banna oro 8,0 mm (M/F)
1 x	Conector Servo female 4 pines
2 x	Connectors banna oro 8,0 mm 5 pcs(Female)
1 x	Banna gold connector 2,5 mm (M/F)
1 x	Wing connector 8pin with pin strip, plug & socket
2 x	Sandwich carbon + poplar 4mm + carbon 480x290 mm
1 x	XH male balance (4S) connector (2 pcs)
1 x	XH female balance (2S) connector (2 pcs)
2 x	XH male balance (5S) connector (2 pcs)
2 x	2 mm male connector (2 pcs) with safety connector
1 x	Conector BEC male (10 pcs)
1 x	Connector CAN 15
1 x	Propeller POWER-PROP 14x9 Izda
1 x	LASER 73" 1.85m (05) PILOT
1 x	EC5-Set female, simple quality, 2 x female pin, 1 x blue housing
1 x	XH male balance (2S) connector (2 pcs)
1 x	Connectors banna oro 0,8 mm (M/F)
1 x	FALCON 20X9 CARBON PROPELLER (GAS)
1 x	Connectors banna oro 6,0 mm (M/F)
1 x	30 cm DEANS female connector
1 x	Propeller POWER-PROP 14x9
1 x	Propeller POWER-PROP 13x9
1 x	800TVL CMOS camera for FPV
2 x	Gold antispark 5,5 mm plug
1 x	Connectors banna gold 5,5 mm (M/F)
1 x	Connectors banna oro 4 mm (M/F) (ultralight)
1 x	EasyFLY Addon
2 x	SIMtransmitter 6 Mode 2
1 x	Interface Jack Adapter IKARUS
1 x	Slave-cable USB Easy Sim
1 x	Interface Realflight Simulator
2 x	Brass control horn M4 short for wire (4 pcs)
1 x	Horn 5/10 with M2 Bearing
1 x	Cable control set
1 x	Horn with ball 55x40
1 x	6 mm red aluminium threaded horn with patella
1 x	Threaded coupler ALU Left M2,5 Ø 3 (2 uds)
1 x	LH long aluminium horn L31xH30 (2pcs)
2 x	Horn 5/20 with M2 Bearing
1 x	Threaded coupler ALU M3 Ø 5 (2 uds)
1 x	LH long black aluminium horn L31xH30 (2pcs)
1 x	6 mm aluminium horn with patella
1 x	Small aluminium horn red (2pcs)
1 x	Horn 6/27 with M3 Bearing
1 x	Tube Pitot to PIXHAWK
1 x	1/6 Pilot "Tony"
1 x	Walnut wood slat 3.0x3.0x1000 mm
1 x	Pine wood slat 1.5x3.0x1000 mm
1 x	Prolongador S-Bus JR/JR 20cm
1 x	Aluminium wide washer M4 Black (4 pcs)
1 x	Split pin 1x8 mm (10 uds)
1 x	Pushrod greyline 3/2 with coupler M3 L: 1000 mm
1 x	Wing bolts M6 Steel screw Blue (2 pcs)
1 x	Triple rod con. 3mm Pushrod (2 pcs)
1 x	Pushrod greyline 3/2 with coupler M2
1 x	Vertical cockpit anchor "tipe F3A" (2 pcs)
1 x	Fully Threaded Steel Rod M2,5 (2 uds)
1 x	Press fitting for 1,0 diam. steel cable (10 pcs)
1 x	Fully Threaded Steel Rod M3
1 x	Screw-lock pushrod conn snap Ø 1.5 mm (2 uds)
1 x	Snap short M2 (10 uds)
1 x	Camera Sony 4140+673 CCD with Built-in 200mw TX + antenna
2 x	XH male balance (3S) connector (2 pcs)
1 x	Cockpit aluminium closing
2 x	Stainless steel cable Ø 1.3 mm (10 m)
1 x	Extra long horn 60x30
1 x	Long extra-strong control horn with bearing 2,8x34
1 x	Threaded coupler ALU M2 Ø 4 (2 uds)
1 x	Brass control horn M2 large for wire (2pcs)
1 x	STEERING FRONT WHEEL SYSTEM BIDULE 111
2 x	Fully Threaded Steel Rod alumin 80 mm M3 (2 pcs)
2 x	Fully Threaded Steel Rod Duralumin 80 mm M3 (2 pcs)
2 x	Window mounting channel 5m
1 x	Tip wing protector 28x10x12 (2 pcs)
1 x	Blue aluminium double servo arm HITEC 2,5 inch M3
1 x	Gold aluminium servo arm V1-JR 1,25" inch M3
1 x	Servo FUTABA SBL 471 SV
1 x	Straightened rod Ø 2.0 mm x 1000 mm
1 x	Aluminium rod Ø 4.0 mm x 3000 mm
1 x	Servo FUTABA HPS-A700 Digital S-Bus
1 x	Blue aluminium servo arm V2-Hitec 1,25 inch M3
1 x	Servo BLUE Bird BLS-H71B v2
1 x	Conector AS150 7mm antichispazo (Set: 2 pares)
1 x	Crimping tool
1 x	Wing Joiner ULTIMATUM 2.0 m
1 x	Servo KST X06H - 1.8Kg.cm 7mm 6g
1 x	aluminium servo arm V2-JR 2,0 inch M3
1 x	SERVO DES 806 Pignons
1 x	SERVO DES 707 BB MG
1 x	Servo KST X10 V2.0 ala 10mm 28g 10.8Kg
1 x	Servo KST X20-7512 V8.0 82kg 8.4v
1 x	Servo KST X10 MINI wing 10mm 23g 7.5Kg
1 x	Oracover GREY Seafire Sea 2m
1 x	Futaba BLS255/272/471SV - Gear Set
1 x	SERVO DES 568 MG
1 x	Gold aluminium double servo arm JR/Graupner 40 mm M3 F3A
1 x	Servo BLS-M55B 61.2kg
1 x	MIG 29 3D RTF, Servo
1 x	Servoholder Dymond DS 1800 MG Digital (2 pcs)
1 x	A/C quality beech plywood 600x300x6.0 mm
1 x	Aluminium servo arm (2 uds)
1 x	SERVO S9177SV HV S-Bus2 Programable
1 x	Servo KST BLS815 HV V2.0 Servo 20mm 70g 20Kg
1 x	2,5x60 mm allen screwdriver
1 x	Copier 5x20 cm pcs
1 x	Extra Hard Titanium Herxagon Screwdrivers
1 x	Copier 2x20 cm pcs
1 x	2,0x50 mm allen screwdriver
1 x	Fresa corte diamante Ø 2.35mm (flame)
1 x	22 mm Cut Disc Proxxon/Dremmel
1 x	Aramid fibre shears Proton®, 21 cm / 8" length
1 x	Digital weight, angle and balance meter BASIC
1 x	Boxed KIT OF 7 Rotary Burrs FINE
1 x	Cut tube
1 x	Dean-T Plug Mold
1 x	DUBRO - KWIK TWIST TOOL - TO TWIST STEEL WIRE (1 PC) (301)
1 x
1 x	1,5x50 mm allen screwdriver
1 x	Fresa corte diamante Ø 2.35mm (lentil)
1 x	Dremel 3000 130W
1 x	Disposable Injector Bags (30x16cm) 100 pcs
1 x	Brass hexagonal rod Ø 3 mm x 1000 mm
1 x	Straightened rod Ø 6.0 mm x 1000 mm
1 x	Straightened rod Ø 2.5 mm x 1000 mm
1 x	Straightened rod Ø 4.0 mm x 1000 mm
1 x	Brass rod Ø 1.0 mm x 1000 mm
1 x	Straightened rod Ø 1.5 mm x 1000 mm
1 x	Straightened rod Ø 1.2 mm x 1500 mm
1 x	Red aluminium servo arm V2-Futaba 1,5" inch M3
1 x	Soporte servo KST X10 mini / DS135MG
1 x	Servo KST A08H V6.0 3,2Kg HV
1 x	Servo KST HS08A Wing Servo - 5.2Kg.cm 0.11s 11.0g 8mm
1 x	Gold aluminium servo arm V2-JR 1,25" inch M3
1 x	Connectors banna oro 2 mm (M/F) (ultralight)
1 x	Servo FUTABA BLS 272SV
1 x	Red aluminium servo arm V1-Futaba 15 mm iM2
1 x	Waterproof adhesive tape, width 19mm, length 25m
1 x	Servo MKS 6100 DS
1 x	Motor KAVAN PRO 2225-1600
1 x	Servo arms set HS-60/81/85/5082MG/5085mg
1 x	Red aluminium servo arm V2-Futaba 1,0" inch M3
1 x	Servo HBS 690BB HV Digital
1 x	Red aluminium servo arm V2-Futaba 1,25" inch M3
1 x	Adaptadores carga 6s JST-XH
1 x	Fast attachment for servos (25 pcs)
1 x	Red aluminium servo arm V1-Futaba 1,5" inch M3
1 x	Connectors MPX male
1 x	Connectors MPX male (PIN double)
1 x	Connectors MPX black male
1 x	Carbon plate 350x150x3.0 mm
1 x	XH female balance (6S) connector (2 pcs)
1 x	Dremel PERMAGRIT 18 mm round lime
1 x	Horn with ball 40x30
1 x	6 mm M3 variable horn
1 x	Long horn 50x26
1 x	Control horn long w/ball
1 x	Adjustable brass horn threaded M3
1 x	Brass control horn M4 short for wire (10pcs)
1 x	Horn mando small (2 pcs)
1 x	Threaded coupler ALU Left M2,5 Ø 4 (2 uds)
1 x	Triple rod con. 2mm Pushrod (2 pcs)
1 x	Propeller Pleg CAM Carbon 12.5x7.5
1 x	Fully Threaded Steel Rod alumin 40 mm M3 (2 pcs)
1 x	Fully Threaded Steel Rod alumin 80 mm M3 (2 pcs)
1 x	Stainless steel cable Ø 0.88 mm - 60 kp (10 m)
1 x	Split pin 1.6x16 mm (10 uds)
1 x	140 mm rods set for direction control
1 x	Cable grommet Ø 5 mm (4 uds)
1 x	Wheel collar 3.5 mm Ø (4 uds)
1 x	Wheel collar 3 mm Ø (4 uds)
1 x	Allen wheel collar M3x3
1 x	Aluminun wheel collar 3.5 mm Ø (4 uds)
1 x	Carbon plate 350x150x1.0 mm
1 x	Cierre cabina aluminio Ø4, I=10 mm
1 x	140 mm rods + T patellas set for direction control
1 x	SUS wire 3m (nylon coated)
1 x	45 mm rods set for direction control
1 x	Propeller Pleg CAM Carbon 15x8
1 x	Propeller Pleg CAM Carbon 10x6
1 x	Propeller Pleg CAM Carbon 11x8
1 x	Propeller Pleg CAM Carbon 12x5
1 x	Fully Threaded Steel Rod alumin 90 mm M3 (2 pcs)
1 x	Fully Threaded Steel Rod alumin 100 mm M3 (2 pcs)
1 x	Fully Threaded Steel Rod alumin 70 mm M3 (2 pcs) knurled
1 x	Fully Threaded Steel Rod alumin 70 mm M3 (2 pcs)
1 x	CARBON CUB 15cc ARF 2280 mm

8,940.92EUR