258.00EUR

DUPLEX 2.4EX Central Box 210
[JETCB210]

JETI Duplex 2.4EX Central Box 210
Product description and features
The Central Box 210 is the successor to the popular Central Box 200. Especially for the use of powerful and power-hungry servos, the Central Box 210 uses an aluminum housing and avoids the over current protection of the servo slots. The Central Box 210 offers true battery redundancy, DITEX servo telemetry, JETI EX telemetry and up to three receiver inputs (2x 2.4GHz and 1x 900MHz) for full power and RF signal redundancy.
Configuration via JETI Duplex DS/DC transmitters
With JETI Duplex DC/DS transmitters, the full potential of the Central Box 210 can be fully exploited. The device overview of the JETI Duplex DS/DC transmitter makes it easy to perform the entire configuration of the servo outputs, DITEX servo and JETI EX telemetry, function assignment, and more.
Compatibility with Futaba
The Central Box 210 can also be used with two S.Bus receivers (e .g Futaba R7003SB). Setting up and reading out the telemetry values must, however, be realized with a separatly available JETIBOX.
Switching on and off The switching on and off process of the Central Box 210 is done with the supplied magnetic switch.
Recommended receivers
As receiver e. g. 2 RSat2 or REX3 receivers can be used. Optionally, the use of a REX Assist receiver in combination with a RSat2 receiver is possible, so you get a Central Box with gyro stabilization.
Features
Configurable servo outputs
Battery connections 2x MPX connector system
Robust aluminum housing for extra cooling and protection
Firmware upgradeable via JETI USB adapter and JETI Studio
Wireless programming via the device overview of the DC/DS transmitters
Up to 3 independent receiver inputs (R1, R2, E1/R3)
Up to 15 servo slots (suitable for DITEX servo telemetry)
Up to 3 telemetry sensor inputs (E1/R3, E2/15, E3/14)
Input for supplied magnetic switch or optional RC switch
Optional over current protection
The Central Box 210 is not equipped with the built-in overload protection of the servo slots. To protect critical servos such tow coupling servos, retractable landing gears or spoiler servos, the optional overload protection DPSI OCP (Accessories tab) can be used.
Feature
Servo outputs 15
Protected servo outputs (for servos with up to 30kg/cm)
Protected servo outputs (for servos with up to 30kg/cm)
Receiver inputs up to 3
Satellite receiver support Yes
Telemetry Yes
DITEX servo telemetry Yes
Battery inputs 2
Supply voltage [V] 4 up to 8.4
Voltage regulator No
Permanent current [A] 20
Peak current (approx. 2 seconds) [A] 90
Idle current [µA] 180
Operating temperature [°C] ([°F]) -20 to 75 (-4 to 167)
Dimensions [mm] ([in]) 66 x 42 x 18 (2.6 x 1.65 x 0.71)
Weight [g] ([oz]) 59 (2.08)

under request

Reviews

Quick Find

Shopping Cart

1 x	PIX Hawk with accesories
1 x	PPM Encoder Module
1 x	Digital Air Speed Sensor And Pitot Tube Set
2 x	Round Rod 6,0x1000 mm
1 x	ABS Strip 1.0x5.0x1000 mm
2 x	Strip 1,5x1,5x330 mm
2 x	ABS I Strip 20x10x1000 mm
1 x	Lock washer 2.2 mm (20 pcs)
1 x	Flat washer 1.7 mm (20 pcs)
1 x	Aluminium wide washer M4 Red (4 pcs)
1 x	M3-M4 rubber washer (8 pcs)
1 x	Aluminium cap bolt washer M3 red (8 pcs)
3 x	Round Rod 1,25x1000 mm
2 x	Strip ABS 2.0x8.0x1000 mm
2 x	ABS I Strip 10x5x1000 mm
1 x	Spring lock washer 3.1 mm (20 pcs)
1 x	Aluminium wide washer M3 red (4 pcs)
3 x	Round Rod 4,0x1000 mm
2 x	Strip ABS 2.0x5.0x1000 mm
1 x	Strip 2,5x1,25x330 mm
1 x	Flat washer 2.7 mm (20 uds)pcs)
1 x	Aluminium cap bolt washer M3 green (8 pcs)
1 x	Quicklock washer 3 mm (10 pcs)
2 x	Strip 3,5x1,75x330 mm
1 x	Circlik for shaft 2.3 mm (10 pcs)
2 x	Aluminium wide washer M4 Blue (4 pcs)
2 x	Strip 2,0x2,0x330 mm
1 x	M3 black washers (4 pcs)
1 x	Flat washer 2.2 mm (20 pcs)
2 x	ABS Strip 1.0x3.0x1000 mm
1 x	Circlik for shaft 1.2 mm (10 pcs)
1 x	Strip ABS 2.0x3.0x1000 mm
1 x	Circlik for shaft 1.5 mm (10 pcs)
1 x	Lock washer 2.7 mm (20 pcs)
1 x	Spring lock washer 4.1 mm (20 pcs)
2 x	Round Rod 5,0x1000 mm
1 x	Quicklock washer 1.5 mm (10 pcs)
1 x	Spring lock washer 2.6 mm (20 pcs)
1 x	Aluminium cap bolt washer M4 red (8 pcs)
2 x	Round Rod 2,5x1000 mm
2 x	Strip ABS 2.0x10.0x1000 mm
2 x	Quicklock washer 2.5 mm (10 pcs)
1 x	Lock washer 3.2 mm (20 pcs)
1 x	Spring lock washer 2.1 mm (20 pcs)
1 x	Aluminium cap bolt washer M3 black (8 pcs)
1 x	Aluminium wide washer M3 gold (4 pcs)
1 x	BALSA triangular 15x15x1000 mm
1 x	BALSA leading edge 8x10x1000 mm
1 x	Linden wood slat 3.0x3.0x1000 mm
1 x	Linden wood slat 2.0x2.0x1000 mm
1 x	Mahogany wood slat 2.0x2.0x1000 mm
1 x	BALSA triangular 8x8x1000 mm
1 x	Liston HAYA 8 x 8 x 1000 mm
1 x	Liston HAYA 10 x 10 x 1000 mm
1 x	BALSA triangular 10x10x1000 mm
1 x	BALSA trip 2.0x2.0x1000 mm
1 x	Pine wood slat 2.0x10.0x1000 mm
1 x	OBECHI sheet 2.0x3.0x1000 mm
1 x	Mahogany wood slat 3.0x3.0x1000 mm
1 x	BALSA trip 3.0x3.0x1000 mm
1 x	Pine wood slat 1.5x3.0x1000 mm
1 x	Pine wood slat 3.0x5.0x1000 mm
1 x	Beech dowels 4.0 x 1000 mm
1 x	Pine wood slat 3.0x10.0x1000 mm
1 x	FALCON 20X9 CARBON PROPELLER (GAS)
1 x	Propeller POWER-PROP 14x9
1 x	Red smoke canister 140 g
1 x	Red smoke bombs AX-60 (5 pcs)
1 x	"S" set for planes
3 x	White smoke bombs AX-60 (5 pcs)
2 x	Initior Receiver FRX2 Wireless
1 x	Yellow smoke canister 140 g
1 x	White smoke canister 100 g
2 x	Green smoke canister 65 g
2 x	Yellow smoke canister 100 g
1 x	Green smoke canister 140 g
2 x	Smoke set "S"
1 x	Red smoke canister 65 g
1 x	White smoke canister 140 g
2 x	Black smoke bombs AX-60 (5 pcs)
1 x	White smoke canister 65 g
3 x	Yellow smoke canister 65 g
1 x	Glases Stratus
2 x	Zurich Sport Sunglasse Dark Sensity MAGENTA Glasses
1 x	Glases Innovation Plus
1 x	Glases Aspen
1 x	Glases Flitemaster
1 x	Extension 7.5 cm
1 x	Extension PVC 150 cm (Graupner)
1 x	Cable grommet Ø 6.4 mm (4 uds)
1 x	45 mm rods + T patellas set for direction control
1 x	15 mm reinforced hinge
1 x	67 mm cylidric hinge Ø 4,5 mm (5 pcs)
1 x	ABS tube 6.0x5.0x1000 mm
1 x	ABS tube 8.0x6.0x1000 mm
1 x	Parachute PV6 for F3J
1 x	1/6 Pilot "Tony"
1 x	Flat washer 4.3 mm (20 pcs)
1 x	ABS Strip 1.5x6.0x1000 mm
1 x	Neck strap JETI DS
2 x	Antenna FUTABA 2.4GHz 3PM/8FG/14SG/18SZ/18M
1 x	MZ-10, 5 Channel HoTT
1 x	Round Rod 3,0x1000 mm
2 x	Switch for DS: Short 2 Position
2 x	Decorative caps, multicoloured
1 x	Transmitter GRAUPNER MZ-24 Pro
2 x	Charger HITEC CG-42 TX 7.2v/ RX 4.8v (80 mA)
1 x	Harness for transmitter JETI DUPLEX
2 x	Futaba Radio Case
1 x	Blind nut M3 (4 pcs)
1 x	Nut for mounting M4 (4 pcs)
1 x	Lock nut M6 (10 pcs)
1 x	Hexagonal Nut M3 (10 pcs)
1 x	Treaded hexagonal socket insert M3 Br (4 pcs)
2 x	Battery RX JETI LiIon RB 5200 7.2v
1 x	Teacher / Student Cable
2 x	Hand Pads for Tray JETI
1 x	Blind nut M5 (10 pcs)
1 x	Nut for mounting M3 (10 pcs)
1 x	Nut for mounting M6 (4 pcs)
1 x	Support hands Issuer PROFI TX
1 x	Blind nut M2 (10 pcs)
1 x	Aluminium cap bolt washer M4 blue (8 pcs)
1 x	Interruptor On/Off Corto micro
1 x	Lock nut M5 (20 pcs)
1 x	DUPLEX 2.4 EX MVario2
1 x	Blind nut M6 (4 pcs)
1 x	Tapping Screw M2.2x9.5 (10 pcs)
1 x	Screw M2.5x20 (10 pcs)
1 x	Pegamento Pu R 50g polyuretano
1 x	resin-hardener package L-385 with hardener H-385 (3.5 Kg)
1 x	White gelcoat 1 Kg
1 x	MEKP Harderner 100 g
1 x	Epoxy Resin L 285 + Hardener 386, kit/ 675g
1 x	Hardener Aero EPH 161 (500 g)
1 x	Alignment dowels (2 parts, outer-Ø 8 mm) bag/ 100 pairs
1 x	Glases Nimbus "Black"
1 x	Lite Plywood panel 600x300x2.0 mm
1 x	Balsa panel 2.5x100x1000 mm
1 x	Zurich Sport Sunglasse Dark Sensity BROWN Glasses
2 x	Glases Nimbus
1 x	A/C quality beech plywood 1520x750x4.0 mm
1 x	A/C quality beech plywood 1520x750x3.0 mm
1 x	Birch plywood plate 600x300x3.0 mm
1 x	400 Newtons FEMA absorber
1 x	Sandwich carbon + poplar 4mm + carbon 290x160 mm
1 x	Carbon plate 350x150x3.0 mm
1 x	Sandwich carbon + poplar 3mm + carbon 290x160 mm
2 x	Mobile Terminal
1 x	Servo GO-1023MG 7.0 kg.cm 0.09s/60º
1 x	Aluminium cap bolt washer M3 blue (8 pcs)
1 x	Aluminium cap bolt washer M4 green (8 pcs)
1 x	Quicklock washer 1 mm (10 pcs)
1 x	Oracover light Grey 2m
1 x	Ventral support for AX-18/AX-60
1 x	Parachutist
2 x	Blue smoke canister 100 g
1 x	Smoke set "Glider"
1 x	Yellow smoke bombs AX-60 (5 pcs)
1 x	Green smoke canister 100 g
1 x	PRO-HV Dual Action Valve
1 x	Landing gear retract neumatic (Jet Legend)
1 x	Neumatic retractable landing gear (Aero-Naut)
1 x	Manometer 4 mm
1 x	Straightened rod Ø 8.0 mm x 1000 mm
1 x	EDGE 540-A 105" (2660 mm)
1 x	Electric rocket starters (6 pcs)
1 x	Remote electric ignition system
1 x	Red smoke canister 100 g
1 x	Glases Moritz
1 x	Parachute expulsion foam
1 x	Glases Ace
1 x	Switch Cap M (red)
1 x	Teacher-student connector T12FG/FX-30
1 x	Transmitter Balancer Futaba V
1 x	Three-function control switch by FUTABA
1 x	Switch for DC: Long 3 Position
1 x	RC Power Switch 5A
1 x	PPM to Jack link - Tx Black (mono) DC/DS Tx DUPLEX 2,4EX
1 x	Black 2,4 GHz antenna exit guides (2 pcs)
1 x	EnLink 2RS Plus - DUO
1 x	Propeller electric carbon 10.5x6
1 x	Propeller POWER-PROP 15x8
1 x	Propeller POWER-PROP 14x8
1 x	Propeller electric carbon 7x7
1 x	DUPLEX 2.4EX Central Box 220 + 2x Rsat2
1 x	Battery RX JETI LiIon RB 6200 7.2v
1 x	Propeller electric carbon 10x7
1 x	DUPLEX 2.4EX MFlow2 Gas 800
1 x	Titanium M3x0,5x6 mm Flat Head screw (4 pcs)
1 x	Tapping Screw M2.2x13 (10 pcs)
1 x	9x4.7 * 22x12 carbon propeller
1 x	Pan Head Screw M1,6x6 (10 pcs)
1 x	Socket Head Screw M2x12
1 x	Spring pin Ø 1 x 6 mm (10 pcs)
1 x	Futaba S-Bus Rx/Gyro Link Lead
2 x	Antenna holder bracket double
1 x	Switch Cap L (black)
1 x	Battery FUTABA 18MZ
1 x	Switch Cap M (silver)
1 x	Switch moment button, 2 functions, long FUTABA
1 x	Interruptor FUTABA FX-MZ (2 Posic. corto)
1 x	ABS Strip 1.0x4.0x1000 mm
1 x	Receiver bed (Blue)
1 x	Transmitter Balancer Futaba T-10CG
1 x	Antenna Hole Cap V1 (Silver)
1 x	Futaba Neckstrap
1 x	FPV Station for SE TX-Tray V1
1 x	ABS Strip 1.5x3.0x1000 mm
1 x	Futaba S-Bus Rx/Gyro Link Lead
1 x	Switch Cap L (Blue)
1 x	Three-function control switch by FUTABA
1 x	Neck strap Double V2
1 x	ABS Strip 1.5x8.0x1000 mm
1 x	Transmitter Balancer HITEC Aurora 9, JR and Spectrum (blue)
1 x	Switch Cap L (silver)
1 x	Round Rod 1,5x1000 mm
1 x	Round Rod 1,0x1000 mm
1 x	Charger FUTABA SQN30W12P-08 220v
1 x	Transmitter Balancer Futaba FF9-DX7-JR-Hitec
1 x	Maleta transporte FUTABA 10PX
1 x	Caps multicolor Switch JETI
1 x	JETImodel DPS 40
1 x	JETI Counter for DC-16 (Blue)
1 x	switch 1-Spring-UP 3-position DC Tx DUPLEX 2,4EX
1 x	switch 1-Spring-DOWN 3-position DC Tx DUPLEX 2,4EX
1 x	Stick with Button DC/DS-16/14/24 Tx DUPLEX 2,4EX
1 x	Neck strap JETI DC
1 x	White 2,4 GHz antenna exit guides (2 pcs)
1 x	DSM 10 Dual Switch Mixer
1 x	switch long 3-position DC Tx DUPLEX 2,4EX
1 x	JETI Counter for DC-24 Carbon Design 3
1 x	Holder for DC Transmitter/Tray DUPLEX 2,4EX
1 x	Screws of the Back Cover for DC Tx (10pcs.)
2 x	Car Charger DC/DS-16
1 x	Black tray 2,4EX DC-16/14/24 black
1 x	DUPLEX 2,4EX Switch SAFETY 2-Position Safety DC-16/14
1 x	DS-12/14/16 - Black nuts for upper switches - Front panel (2pcs)
1 x	PPM to Jack link - Tx Red (stereo) DC/DS Tx DUPLEX 2,4EX
1 x	Battery RX JETI LiIon RB 3100 7.2v
1 x	Propeller POWER-PROP 13x8
1 x	DUPLEX 2.4EX MAlti (Rev.2)
1 x	DUPLEX 2.4EX MUI 150 Sensor
1 x	Propeller electric carbon 8.5x7
1 x	Propeller electric carbon 10.5x8
1 x	Propeller POWER-PROP 12x8
1 x	DUPLEX 2.4EX MT 125 temperature sensor
1 x	Propeller electric carbon 8.5x5
1 x	Propeller POWER-PROP 14x12

10,120.90EUR